Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM37A0E _59 Vehicle Exterior _086900 SLIDING ROOF / CONVERTIBLE _0420295 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof does not Move by Operating Sliding Roof Control Switch  


DESCRIPTION

The sliding roof ECU (sliding roof drive gear assembly) receives slide and tilt signals and operates its built-in motor when the sliding roof switch (map light assembly) is operated.

WIRING DIAGRAM

B567707E03
0.469,4.771 3.833,5.156 3.365,0.385 10 false Sliding Roof Switch (Map Light assembly) 4.667,4.792 6.573,5.25 1.906,0.458 10 true Sliding Roof ECU (Sliding Roof Drive Gear Assembly) 1.26,1.094 2.708,1.344 1.448,0.25 10 false from Auxiliary Battery 2.156,2.771 3.667,3.021 1.51,0.25 10 false UP 1.906,3.146 3.417,3.396 1.51,0.25 10 false DOWN 3.396,1.292 4.906,1.542 1.51,0.25 10 false S/ROOF 4.438,1.021 4.698,1.292 0.26,0.271 10 false B 4.427,2.01 5.938,2.26 1.51,0.25 10 false OPN 4.458,2.396 5.969,2.646 1.51,0.25 10 false CLS 4.438,2.781 5.948,3.031 1.51,0.25 10 false OPN 4.438,3.156 5.948,3.406 1.51,0.25 10 false CLS 4.438,3.521 4.958,3.896 0.521,0.375 10 false E 2.042,2.01 3.552,2.26 1.51,0.25 10 false OPN 2.052,2.396 3.563,2.646 1.51,0.25 10 false CLS 2.031,3.531 3.542,3.781 1.51,0.25 10 false GND 0.479,4.583 1.99,4.833 1.51,0.25 10 false R11 4.677,4.625 6.188,4.875 1.51,0.25 10 false R2 4.24,1.01 4.5,1.281 0.26,0.271 10 false 1 4.188,2.01 4.448,2.281 0.26,0.271 10 false 10 4.26,2.375 4.521,2.646 0.26,0.271 10 false 8 4.26,2.74 4.521,3.01 0.26,0.271 10 false 5 4.26,3.125 4.521,3.396 0.26,0.271 10 false 9 4.271,3.521 4.531,3.792 0.26,0.271 10 false 2 2.427,2.01 2.688,2.281 0.26,0.271 10 false 20 2.427,2.396 2.688,2.667 0.26,0.271 10 false 19 2.427,2.76 2.688,3.031 0.26,0.271 10 false 17 2.417,3.146 2.677,3.417 0.26,0.271 10 false 18 2.417,3.531 2.677,3.802 0.26,0.271 10 false 11 3.229,0.792 4.74,1.042 1.51,0.25 10 false ECU-IG1 NO. 4 1.292,0.615 2.802,0.865 1.51,0.25 10 false from IG1-NO.1 Relay 4.448,0.542 4.708,0.813 0.26,0.271 10 false IG 4.25,0.531 4.51,0.802 0.26,0.271 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the sliding roof ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

If a sliding roof ECU (sliding roof drive gear assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear assembly) DTC.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SLIDING ROOF)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Sliding Roof > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Slide Roof Operate sliding roof motor OFF / Opn/Dwn / Clos/Up -
Body Electrical > Sliding Roof > Active Test
Tester Display
Slide Roof
50004 147 1
OK:

Slide roof is operated using GTS.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - IG POWER SUPPLY AND BODY GROUND)
2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal OFF or ON OFF: OPEN switch not pressed
ON: OPEN switch pressed
-
Close Switch CLOSE switch signal OFF or ON OFF: CLOSE switch not pressed
ON: CLOSE switch pressed
-
Up Switch UP switch signal OFF or ON OFF: UP switch not pressed
ON: UP switch pressed
-
Down Switch DOWN switch signal OFF or ON OFF: DOWN switch not pressed
ON: DOWN switch pressed
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch
Close Switch
Up Switch
Down Switch
50003 147 1,4,7,10
OK:

The GTS display changes according to the operation of each switch as shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

3.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)
3.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)

NG

REPLACE SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)
a.

Disconnect the R11 sliding roof switch (map light assembly) connector.


b.

Disconnect the R2 sliding roof ECU (sliding roof drive gear assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-8 (CLS) - R11-19 (CLS) Always Below 1 Ω
R2-8 (CLS) or R11-19 (CLS) - Body ground Always 10 kΩ or higher
R2-10 (OPN) - R11-20 (OPN) Always Below 1 Ω
R2-10 (OPN) or R11-20 (OPN) - Body ground Always 10 kΩ or higher
R2-9 (CLS) - R11-18 (DOWN) Always Below 1 Ω
R2-9 (CLS) or R11-18 (DOWN) - Body ground Always 10 kΩ or higher
R2-5 (OPN) - R11-17 (UP) Always Below 1 Ω
R2-5 (OPN) or R11-17 (UP) - Body ground Always 10 kΩ or higher
R11-11 (GND) - Body ground Always Below 1 Ω
R2-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF DRIVE GEAR ASSEMBLY (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - IG POWER SUPPLY AND BODY GROUND)
a.
B425565C68
1.469,0.167 1.917,0.385 0.448,0.219 2.385,1.115 1.958,1.115 false 1.469,1.104 0.969,1.104 false 2.396,1.292 1.969,1.292 false 1.573,0.198 1.885,0.396 0.313,0.198 10 false R2 2.438,1.031 2.76,1.271 0.323,0.24 10 false E 0.146,0.104 0.531,0.427 0.385,0.323 10 false *a 0.844,1.021 1.167,1.26 0.323,0.24 10 false B 2.448,1.219 2.771,1.458 0.323,0.24 10 false IG
*a Front view of wire harness connector
(to Sliding Roof ECU (Sliding Roof Drive Gear Assembly))


Disconnect the R2 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R2-1 (B) - Body ground Ignition switch off 11 to 14 V
R2-6 (IG) - Body ground Ignition switch ON 11 to 14 V
R2-6 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR