The occupant detection sensor (separate type front seat cushion pad (front passenger seat)) detects if the passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt assembly (front passenger seat) detects the passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the occupant detection sensor (separate type front seat cushion pad (front passenger seat)) and front seat inner belt assembly (front passenger seat), the seat belt warning light on the combination meter assembly will blink or go off.
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION
If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Passenger Buckle Switch | Front passenger seat belt buckle switch signal | Fastened or Not Fastened | Fastened: Front passenger seat belt buckle switch fastened
Not Fastened: Front passenger seat belt buckle switch unfastened |
- |
| Passenger Occupant Detection Switch | Front passenger occupant detection sensor | OFF or ON | OFF: Front passenger seat not occupied
ON: Front passenger seat occupied |
- |
| Tester Display |
|---|
| Passenger Buckle Switch |
| Passenger Occupant Detection Switch |
The GTS display changes correctly in response to the front passenger seat belt and front passenger seat condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Passenger Buckle Switch) | B |
| NG (Passenger Occupant Detection Switch) | C |
A
B
C
for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>INSPECTION
for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
Disconnect the H21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M28-3 (+) - H21-10 (PBKL) | Always | Below 1 Ω |
| M28-3 (+) or H21-10 (PBKL) - Body ground | Always | 10 kΩ or higher |
| M28-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>INSPECTION
for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR (for Front Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M28-5 (+) - H21-11 (PODS) | Always | Below 1 Ω |
| M28-5 (+) or H21-11 (PODS) - Body ground | Always | 10 kΩ or higher |
| M28-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG