Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.
When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)
While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
43512
1.INSTALL FRONT DISC
| *a | Matchmark |
Align the matchmarks of the front disc and front axle hub sub-assembly, and install the front disc.
When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.
47722
2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING
Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.
3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.
Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each front disc brake bushing dust boot.
Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.
47715A
4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the contact surface of the front disc brake cylinder slide pin (lower side) and a new front disc brake cylinder slide bushing.
Install the front disc brake cylinder slide bushing to the front disc brake cylinder slide pin (lower side).
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the 2 front disc brake cylinder slide pins.
Install the 2 front disc brake cylinder slide pins to the front disc brake cylinder mounting.
Push each front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.
5.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting.
Be sure to install each front disc brake pad support plate in the correct position and direction.
04945
6.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT
7.INSTALL FRONT DISC BRAKE PAD
Install the 2 front disc brake pads to the front disc brake cylinder mounting.
Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.
Install the front disc brake pad so that the front disc brake pad wear indicator plate is mounted on the upper side of the vehicle.
Install the 2 anti-squeal springs to the front disc brake pads.
When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.
Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.
47750
8.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY
Hold each front disc brake cylinder slide pin and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.
Install the front disc brake cylinder assembly while holding both of the front disc brake pads because the anti-squeal springs may fall off the front disc brake pads.
Be sure that the anti-squeal springs are installed to the front disc brake pads.
47313J
9.CONNECT FRONT FLEXIBLE HOSE
Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.
Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.
10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)
Connect the reservoir level switch connector.
Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.
Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION
Perform the following procedure if air bleeding is not necessary:
Turn the ignition switch to ON (READY).
Depress the brake pedal and release it.
11.BLEED BRAKE LINE
for HV Model: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING
for Gasoline Model: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>BLEEDING
12.INSTALL FRONT WHEEL