Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model)
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0420832 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  B1449  Air Outlet Damper Control Servo Motor Circuit (Rear)  


DESCRIPTION

The rear mode damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position.

The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear mode damper servo sub-assembly to the appropriate position, which controls the air outlet switching.

The air conditioning amplifier assembly communicates with the servo through the communication/driver IC and wiring assembly called the No. 2 air conditioning harness assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1449 Air Outlet Damper Control Servo Motor Circuit (Rear) Air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates rear mode damper servo sub-assembly
·

Rear mode damper servo sub-assembly

·

No. 2 air conditioning harness assembly

·

Air conditioning amplifier assembly

·

Rear cooling unit assembly


Memorized
(30 sec. or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.

DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Rear mode damper servo sub-assembly operating ○ ○
Malfunction Damper servo operation request signals are output but the damper position sensor value does not change ○ -
Damper servo operation request signals are output but the damper position sensor value is abnormal - ○
Detection Time Continuously for 30 seconds or more Continuously for 30 seconds or more
Trip Count 1 trip 1 trip

HINT:

If the conditions of either of these patterns are detected, a DTC will be stored.


WIRING DIAGRAM

E432282E01
0.76,5.333 2.469,5.552 1.708,0.219 10 false : LIN Communication Line 3.281,1.135 3.594,1.333 0.313,0.198 10 false IC 3.292,3.344 3.604,3.542 0.313,0.198 10 false IC 1.177,1 2.177,1.396 1,0.396 10 false Rear Passenger Side Mode 1.188,3.229 2.198,3.615 1.01,0.385 10 false Rear Passenger Side Air Mix 1.031,1.896 3.667,2.135 2.635,0.24 10 false Rear Mode Damper Servo Sub-assembly 1.031,4.125 3.74,4.365 2.708,0.24 10 false Rear Air Mix Damper Servo Sub-assembly 3.75,4.604 5.094,5.063 1.344,0.458 10 false No. 2 Air Conditioning Harness Assembly 5.5,4.927 7.042,5.292 1.542,0.365 10 false Air Conditioning Amplifier Assembly 5.938,0.833 6.5,1.052 0.563,0.219 10 false RBUS 5.938,1.229 6.552,1.427 0.615,0.198 10 false RBBU 5.938,1.406 6.552,1.604 0.615,0.198 10 false RBUG

CAUTION / NOTICE / HINT

NOTICE:
·

Confirm that no mechanical problems are present because this DTC can be stored when either a damper link or damper is mechanically locked.

·

When installing a damper servo motor, make sure to install it correctly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>REASSEMBLY

·

After replacing a damper servo motor, make sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>INITIALIZATION



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B149A is not output A
DTC B149A is output B



A

2.CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY (INSTALLATION CONDITION)

B

2.CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY (INSTALLATION CONDITION)
a.

Check that the rear mode damper servo sub-assembly is installed correctly.

OK:

The rear mode damper servo sub-assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

3.CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER)

NG

REINSTALL REAR MODE DAMPER SERVO SUB-ASSEMBLY

3.CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER)
a.

Check for a wire harness caught between the links of the motors and dampers.

OK:

No wire harnesses are caught between the links of the motors and dampers.



Result:
Proceed to
OK
NG



OK

4.CHECK REAR COOLING UNIT ASSEMBLY (DAMPER)

NG

REMOVE PINCHED WIRE HARNESS

4.CHECK REAR COOLING UNIT ASSEMBLY (DAMPER)
a.

Remove the rear mode damper servo sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY


b.

Operate the dampers by hand.

OK:

The dampers are easily operated by hand.



Result:
Proceed to
OK
NG



OK

REPLACE REAR MODE DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE REAR COOLING UNIT ASSEMBLY