Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model)
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0420832 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  B1498  Communication Malfunction (A/C Inverter Local)  


DESCRIPTION

The hybrid vehicle control ECU and compressor with motor assembly communicate via a direct line. Compressor control is stopped and this DTC is stored if communication information is cut off or abnormal information occurs.

This DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.

This DTC will be stored as a history DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1498 Communication Malfunction (A/C Inverter Local)
·

Error or open in communication line between the hybrid vehicle control ECU and compressor with motor assembly

·

High-voltage power source shut off


·

CAN communication system

·

Hybrid control system

·

Charging system

·

Harness or connector

·

Compressor with motor assembly

·

HV air conditioning wire


Memorized

WIRING DIAGRAM

E432285E01
3.469,2.104 3.927,2.302 0.458,0.198 10 false LIN 1.396,1.052 1.854,1.25 0.458,0.198 10 false 2 5.885,4.031 7.094,4.396 1.208,0.365 10 false Air Conditioning Amplifier Assembly 0.771,3.51 1.229,3.708 0.458,0.198 10 false DOUT 0.917,0.698 1.375,0.896 0.458,0.198 10 false IG1 0.833,1.25 1.292,1.448 0.458,0.198 10 false GND 0.969,5.125 1.427,5.323 0.458,0.198 10 false PB 0.969,5.635 1.427,5.833 0.458,0.198 10 false PE 1.344,5.115 1.781,5.292 0.438,0.177 10 false m1 1.313,3.5 1.75,3.677 0.438,0.177 10 false C65 3.292,1.938 3.75,2.135 0.458,0.198 10 false 2 1.396,0.479 1.854,0.677 0.458,0.198 10 false 1 1.385,3.292 1.844,3.49 0.458,0.198 10 false 3 1.406,4.927 1.865,5.125 0.458,0.198 10 false 2 1.396,5.438 1.865,5.635 0.469,0.198 10 false 1 2.927,2.427 3.385,2.625 0.458,0.198 10 false M7 2.927,2.594 5.031,2.833 2.104,0.24 10 false Battery State Sensor Assembly 2.167,0.833 3.24,1.115 1.073,0.281 10 false ECU-IG1 NO. 3 1.885,6.188 3.49,6.427 1.604,0.24 10 false HV Air Conditioning Wire 0.25,6.177 1.292,6.573 1.042,0.396 10 false Compressor with Motor Assembly 0.979,7.438 2.74,7.646 1.76,0.208 10 false : CAN Communication Line 0.979,7 2.625,7.219 1.646,0.219 10 false : LIN Communication Line 4.094,6.188 6.156,6.406 2.063,0.219 10 false Inverter with Converter Assembly 3.75,5.115 4.01,5.323 0.26,0.208 10 false m2 3.021,4.021 4.74,4.271 1.719,0.25 10 false Hybrid Vehicle Control ECU 3.052,3.51 3.49,3.688 0.438,0.177 10 false A31 3.802,4.917 4.021,5.125 0.219,0.208 10 false 1 3.813,5.438 4.271,5.635 0.458,0.198 10 false 2 4.146,5 4.583,5.177 0.438,0.177 10 false ACPB 4.146,5.521 4.583,5.698 0.438,0.177 10 false ACPE 3.458,3.51 3.896,3.688 0.438,0.177 10 false LIN3 3.146,3.313 3.604,3.51 0.458,0.198 10 false 8 3.75,0.688 5.74,0.885 1.99,0.198 10 false from IG1-NO. 1 Relay 1.344,5.635 1.781,5.813 0.438,0.177 10 false m1 1.313,1.26 1.75,1.438 0.438,0.177 10 false C65 1.313,0.688 1.75,0.865 0.438,0.177 10 false C65 3.75,5.635 4.01,5.844 0.26,0.208 10 false m2

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.

·

Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the ignition switch is turned to ON (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.

·

The air conditioning system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication systems are functioning properly.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK FOR DTC (HYBRID CONTROL)

B

2.CHECK FOR DTC (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

B

6.CHECK FOR DTC (HYBRID CONTROL)
3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the C65 compressor with motor assembly connector.


b.

Disconnect the A31 hybrid vehicle control ECU connector.


c.

Disconnect the M7 battery state sensor assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-3 (DOUT) - A31-8 (LIN3) Always Below 1 Ω
C65-3 (DOUT) or A31-8 (LIN3) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.
E432368C01
1.448,0.188 1.948,0.438 0.5,0.25 1.688,1.115 1.365,1.688 true 1.542,1.052 1.125,0.771 true 0.583,0.146 0.896,0.344 0.313,0.198 10 false *a 1.573,0.24 1.885,0.438 0.313,0.198 10 false C65 1.01,1.615 1.396,1.813 0.385,0.198 10 false GND 0.844,0.635 1.229,0.833 0.385,0.198 10 false IG1
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


Disconnect the C65 compressor with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C65-1 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.INSPECT HV AIR CONDITIONING WIRE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HV AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
m1-2 (PB) - m2-1 (ACPB) Always Below 1 Ω
m1-1 (PE) - m2-2 (ACPE) Always Below 1 Ω
m1-2 (PB) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

6.CHECK FOR DTC (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P058A01 and P162B87 are not output A
P058A01 or P162B87 is output B



A

B