Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for A25A-FXS, A25B-FXS)
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0417371 COMPRESSOR(for A25A-FXS, A25B-FXS) A

HEATING / AIR CONDITIONING  COMPRESSOR(for A25A-FXS, A25B-FXS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during compressor with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION


·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:

After turning the ignition switch is turned off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.CHECK TERMINAL VOLTAGE

Hide 88703 4.REMOVE DISCHARGE HOSE SUB-ASSEMBLY

a.
E431366

Remove the bolt and disconnect the discharge hose sub-assembly from the cooler condenser assembly.


b.
E431367

Remove the bolt and discharge hose sub-assembly from the compressor with motor assembly.


c.

Remove the 2 O-rings from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



Hide 88704 5.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E431368

Remove the bolt and disconnect the suction hose sub-assembly from the compressor with motor assembly.


b.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



Hide 88370 6.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

a.
E431369

Disconnect the 2 connectors.


b.
E431370C01
1.208,0.542 1.542,0.333 true 2.333,1.99 2.781,1.823 true 2.281,2.76 2.604,3.021 true 1.573,0.25 1.885,0.406 0.313,0.156 10 false *c 2.792,1.729 2.958,1.927 0.167,0.198 10 true *a 2.604,2.948 2.792,3.125 0.188,0.177 10 true *b
*a Connector (A)
*b Connector (B)
*c Green-colored Lock
V100137

Slide


Using a screwdriver, slide the green-colored lock of the connector (A) as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



c.

Disconnect the connector (B).


d.
E431371C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and 2 nuts.


e.
E431372

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor with motor assembly.