Home › Drivetrain › P810 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE FLUID
RM37A0E _52 Drivetrain _086860 P810 HYBRID TRANSMISSION / TRANSAXLE _0420888 HYBRID TRANSAXLE FLUID G

P810 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE FLUID  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

For the hybrid transaxle fluid, use Toyota Genuine ATF WS.

Using hybrid transaxle fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transaxle of the vehicle.


PROCEDURE

Hide 53852B 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851D 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51420 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 5.INSPECT HYBRID TRANSAXLE FLUID

NOTICE:

To obtain an accurate measurement, make sure to operate the engine assembly and oil pump with motor assembly as specified in the following procedure before checking the hybrid transaxle fluid level.


HINT:

If no parts have been removed and installed, it is not necessary to start the oil pump with motor assembly (step #) when replacing the hybrid transaxle fluid, performing a fluid level inspection, etc.


a.

Start the engine assembly.

i.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


ii.

Idle the engine for 30 seconds with the ignition switch ON (READY).


iii.

Turn the ignition switch off.



b.

Start the oil pump with motor assembly. [#]

i.

According to the display on the GTS perform the Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display
Control the Motor/Generator Cooling Oil Pump
50004 397 42002
NOTICE:

The active test is not performed when the Duty ratio 50 % or lower or 95 % or higher, or the ambient temperature is 10 °C (50 °F) or lower.



ii.

Start the oil pump with motor assembly and wait for 30 seconds.


iii.

Stop the oil pump with motor assembly.


iv.

Turn the ignition switch off.



c.
C426922

Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly.


d.
C426921C01
3.063,1.719 3.323,1.938 0.26,0.219 10 false *a
*a 0 to 10 mm (0 to 0.394 in.)


Check that the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening.

NOTICE:
·

When inspecting the hybrid transaxle fluid, make sure that the vehicle is level.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

Driving the vehicle with an insufficient or excessive amount of hybrid transaxle fluid may damage the hybrid vehicle transaxle assembly.

·

If the hybrid transaxle fluid was replaced or if hybrid transaxle fluid was added, make sure to recheck the hybrid transaxle fluid level after starting the engine assembly and oil pump with motor assembly.




e.

Check for leaks if the hybrid transaxle fluid level is low. (If there are no hybrid transaxle fluid leaks but the hybrid transaxle fluid level is low, add hybrid transaxle fluid.)

Click hereDrivetrain>P810 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID TRANSAXLE FLUID>ADJUSTMENT


f.

Using a 10 mm hexagon socket wrench, install the filler plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 6.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 51420 7.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53851D 9.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852B 10.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH