The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3. DISCHARGE FUEL SYSTEM PRESSURE
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.SECURE STEERING WHEEL
6.REMOVE FRONT WHEELS
53852B
7.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Remove the 4 screws and front wheel opening extension pad LH.
53851D
8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Remove the 4 screws and front wheel opening extension pad RH.
51441
9.REMOVE NO. 1 ENGINE UNDER COVER
|
Bolt |
|
Screw |
Remove the 3 bolts, 8 screws, 2 clips and No. 1 engine under cover.
51420
10.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
|
Bolt |
|
Screw |
|
Clip |
Remove the 2 bolts, 2 screws, 6 clips and No. 2 engine under cover assembly.
53737B
11.REMOVE FRONT FENDER APRON SEAL LH
Remove the 2 bolts, clip and front fender apron seal LH.
53736
12.REMOVE FRONT FENDER APRON SEAL RH
Remove the 2 bolts, clip and front fender apron seal RH.
13.REMOVE HEADLIGHT ASSEMBLY LH
52618
14.REMOVE FRONT BUMPER LOWER ABSORBER
52132A
15.REMOVE NO. 2 FRONT BUMPER REINFORCEMENT
16.DRAIN ENGINE COOLANT
17.DRAIN ENGINE OIL
18.DRAIN HYBRID TRANSAXLE FLUID
12601B
19.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
Lift the front of the No. 1 engine cover sub-assembly to disengage the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to disengage the clip and remove the No. 1 engine cover sub-assembly.
Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.
G9200
20.REMOVE INVERTER WITH CONVERTER ASSEMBLY
23820
21.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
Disengage the clamp.
Disconnect the fuel vapor feed hose assembly from the No. 1 vacuum switching valve assembly.
87246B
22.DISCONNECT OUTLET HEATER WATER HOSE B
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the outlet heater water hose B from the No. 2 water by-pass pipe sub-assembly.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater water hose B connector with plastic bags to prevent damage and contamination.
87245B
23.DISCONNECT INLET HEATER WATER HOSE B
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the inlet heater water hose B from the flow shutting valve (water by-pass hose assembly).
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater water hose B connector with plastic bags to prevent damage and contamination.
23901
24.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the EFI fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
16571C
25.DISCONNECT NO. 1 RADIATOR HOSE
Disengage the clamp.
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
16572D
26.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the water inlet with thermostat sub-assembly.
88703
27.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
Remove the bolt and disconnect the discharge hose sub-assembly from the compressor with motor assembly.
Remove the O-ring from the discharge hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.
88704
28.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
G9229A
29.DISCONNECT NO. 5 INVERTER COOLING HOSE
Slide the clip and disconnect the No. 5 inverter cooling hose from the motor cooling cooler.
32930F
30.DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE ASSEMBLY
| *1 | Inlet Motor Hose |
| *2 | Outlet Motor Hose |
Disengage the clamp.
Slide the clip and disconnect the inlet motor hose from the hybrid vehicle transaxle assembly.
Slide the clip and disconnect the outlet motor hose from the hybrid vehicle transaxle assembly.
31.DISCONNECT WIRE HARNESS
After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.
Disengage the 3 claws and remove the No. 1 relay block cover from the No. 1 engine room relay block and No. 1 junction block assembly.
Remove the nut from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the 4 connectors from the No. 1 engine room relay block and No. 1 junction block assembly.
Using a screwdriver, disengage the claw and disconnect the wire harness from the No. 1 engine room relay block and No. 1 junction block assembly.
Remove the 2 bolts and disconnect the earth wire.
16281N
32.DISCONNECT NO. 4 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 4 water by-pass hose from the No. 3 water by-pass pipe.
45220
33.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
58166A
34.REMOVE FRONT FLOOR COVER LH
|
Bolt |
|
Screw |
|
Clip |
Remove the 5 bolts, 3 screws, 2 clips (A) and clip (B) and disengage the 5 clamps to remove the front floor cover LH from the vehicle body.
58165C
35.REMOVE FRONT FLOOR COVER RH
|
Bolt |
|
Screw |
|
Clip |
Remove the 3 bolts, 3 screws and clip and disengage the 4 clamps to remove the front floor cover RH from the vehicle body.
17410
36.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
37.REMOVE FRONT DRIVE SHAFT ASSEMBLY
38.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the 4 bolts and engine mounting stay LH from the engine mounting insulator sub-assembly LH.
Remove the 4 bolts and separate the engine mounting insulator sub-assembly LH from the hybrid vehicle transaxle assembly.
|
Bolt |
|
Nut |
Remove the 2 bolts (A), 2 bolts (B) and 4 nuts and front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.
Remove the 4 bolts (C) and 2 bolts (D) and front suspension member brace rear RH and front suspension member brace rear LH from the front frame assembly and vehicle body.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
23825
39.REMOVE FUEL DELIVERY GUARD
Remove the bolt and fuel delivery guard from the engine mounting bracket RH.
40.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 90105-A0354 or
91552-F1040 |
Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
11361J
41.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the flywheel housing under cover from the cylinder block sub-assembly.
45319
42.REMOVE STEERING GEAR HEAT INSULATOR
82121
43.REMOVE ENGINE WIRE
Disconnect all clamps and connectors and remove the engine wire from the engine assembly with transaxle.
821H2
44.REMOVE HV AIR CONDITIONING WIRE
Disengage the 2 clamps.
| *a | Green-colored Lock |
|
Slide |
Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.
Make sure to wear insulated gloves.
Insulate the disconnected terminals and connector with insulating tape.
Remove the 2 bolts.
Disengage the guide to remove the HV air conditioning wire from the hybrid vehicle transaxle assembly.
32930G
45.DISCONNECT NO. 2 TRANSMISSION OIL COOLER HOSE ASSEMBLY
35300B
46.REMOVE OIL PUMP WITH MOTOR ASSEMBLY
11363A
47.REMOVE FLYWHEEL HOUSING SIDE COVER
51100G
48.REMOVE FRONT FRAME ASSEMBLY
12361A
49.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Remove the bolt and front engine mounting insulator from the front engine mounting bracket.
12371A
50.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Remove the bolt and wire harness clamp from the rear engine mounting insulator.
Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.
30900
51.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
31270
52.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY
13405
53.REMOVE FLYWHEEL SUB-ASSEMBLY
19315
54.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
55.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine assembly to an engine stand.
56.REMOVE ENGINE HANGERS
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.
G92A0A
57.DISCONNECT INVERTER RESERVE TANK ASSEMBLY
| *a | Pin |
| *b | Grommet |
Remove the 2 bolts.
Disengage the pin and disconnect the inverter reserve tank assembly.
12305
58.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the bolt and No. 1 inverter reserve tank bracket.
Disengage the 2 clamps.
|
Bolt |
|
Nut |
Remove the bolt, nut and disconnect the radiator reserve tank assembly.
Remove the bolt and disconnect the No. 2 earth wire from the engine mounting insulator sub-assembly RH.
|
Bolt |
|
Nut |
Remove the 2 bolts and nut and remove the engine mounting insulator sub-assembly RH.
12341
59.REMOVE ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Remove the 2 bolts and engine mounting spacer from the vehicle body.
12306
60.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.
|
Bolt |
|
Nut |
Remove the 2 bolts, nut and the engine mounting insulator sub-assembly LH.