Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086906 A25A-FXS, A25B-FXS ENGINE MECHANICAL _0418984 ENGINE ASSEMBLY A

A25A-FXS, A25B-FXS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 12306 1.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.


a.
A455218N01
2.406,1.865 2.563,2.063 0.156,0.198 10 true A 0.729,1.542 0.885,1.74 0.156,0.198 10 true B 1.896,0.094 2.052,0.292 0.156,0.198 10 true C

Install the engine mounting insulator sub-assembly LH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).



Hide 12341 2.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A455217N01
1.479,1.771 1.667,1.969 0.188,0.198 10 true A 2.458,1.167 2.615,1.365 0.156,0.198 10 true B

Install the engine mounting spacer to the vehicle body with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).



Hide 12305 3.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A455216N01
0.833,1.198 0.99,1.396 0.156,0.198 10 true A 2.615,0.854 2.771,1.052 0.156,0.198 10 true B 2.26,0.042 2.417,0.24 0.156,0.198 10 true C

Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.

Connect the No. 2 earth wire to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the radiator reserve tank assembly with the bolt and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Engage the 2 clamps.


e.

Install the No. 1 inverter reserve tank bracket with the bolt.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide G92A0A 4.CONNECT INVERTER RESERVE TANK ASSEMBLY

a.
A455184C01
2.792,0.563 2.958,0.563 false 2.323,0.979 2.635,0.979 true 3.01,0.469 3.25,0.667 0.24,0.198 10 true *a 2.063,0.885 2.302,1.083 0.24,0.198 10 true *b
*a Pin
*b Grommet


Fit the pin of the inverter reserve tank assembly into the grommet as shown in the illustration.


b.

Connect the inverter reserve tank assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 19315 7.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 30900 10.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 12371A 11.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A455219C02
0.688,1.802 0.688,1.521 false 2.156,1.781 2.156,1.5 false 1.073,1.135 1.073,0.677 1.073,0.677 1.229,0.677 false 1.302,1.583 1.302,1.302 false 2.542,1.875 2.542,1.24 true 2.604,0.917 2.698,0.458 2.698,0.458 2.813,0.458 false 2.99,1.969 2.854,1.969 2.854,1.969 2.698,1.427 false 3.031,0.74 2.885,0.74 2.885,0.74 2.833,1.177 true 0.604,1.844 0.917,2.042 0.313,0.198 10 false *1 2.083,1.823 2.396,2.021 0.313,0.198 10 false *2 1.24,1.604 1.552,1.802 0.313,0.198 10 false *a 1.281,0.594 1.594,0.792 0.313,0.198 10 false *b 2.479,1.896 2.792,2.094 0.313,0.198 10 false *b 2.854,0.365 3.167,0.563 0.313,0.198 10 false *c 3.031,1.885 3.344,2.083 0.313,0.198 10 false *c 3.083,0.646 3.396,0.844 0.313,0.198 10 false *d
*1 Rear Engine Mounting Bracket
*2 Rear Engine Mounting Insulator
*a Protrusion
*b Hole
*c Wall
*d Gap


Align and insert the protrusion of the rear engine mounting insulator bracket into the gap between the 2 inner walls of the rear engine mounting insulator to align the hole of the engine mounting insulator bracket with the bolt hole of the rear engine mounting insulator, and install the rear engine mounting insulator with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


b.

Install the wire harness clamp to the rear engine mounting insulator with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12361A 12.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.

Install the front engine mounting insulator to the front engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 51100G 13.INSTALL FRONT FRAME ASSEMBLY

Hide 11363A 14.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 35300B 15.INSTALL OIL PUMP WITH MOTOR ASSEMBLY

Hide 32930G 16.CONNECT NO. 2 TRANSMISSION OIL COOLER HOSE ASSEMBLY

Hide 821H2 17.INSTALL HV AIR CONDITIONING WIRE

a.

Engage the guide to install the HV air conditioning wire to the hybrid vehicle transaxle assembly.


b.

Install the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
A407268C02
1.313,0.552 1.583,0.26 1.583,0.26 1.708,0.26 true 1.771,0.188 2.083,0.385 0.313,0.198 10 false *a
*a Green-colored Lock
V100137

Slide


Connect the connector and slide the green-colored lock as shown in the illustration to lock it securely.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Make sure that the connector is connected securely.



d.

Engage the 2 clamps.


Hide 82121 18.INSTALL ENGINE WIRE

a.

Connect all connectors and clamps, and install the engine wire to the engine assembly with transaxle.


Hide 45319 19.INSTALL STEERING GEAR HEAT INSULATOR

Hide 11361J 20.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 21.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


c.

Install the fuel delivery guard to the engine mounting bracket RH with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




e.
A455204C01
0.854,0.094 1.01,0.292 0.156,0.198 10 true A 2.469,0.115 2.625,0.313 0.156,0.198 10 true A 0.115,2.365 0.271,2.563 0.156,0.198 10 true B 3.146,2.375 3.302,2.573 0.156,0.198 10 true B 0.417,3.74 0.573,3.938 0.156,0.198 10 true C 0.875,4.469 1.031,4.667 0.156,0.198 10 true C 1.365,3.99 1.521,4.188 0.156,0.198 10 true D 1.917,3.99 2.073,4.188 0.156,0.198 10 true D 2.854,3.708 3.01,3.906 0.156,0.198 10 true C 2.833,4.438 2.99,4.635 0.156,0.198 10 true C
V100135

Bolt
V100136

Nut


Install the front bumper extension sub-assembly RH and front bumper extension sub-assembly LH to the front frame assembly and vehicle body with the 4 bolts and 4 nuts.

Torque:
Bolt (A) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Bolt (B) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Nut : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


f.

Install the front suspension member brace rear RH and front suspension member brace rear LH to the front frame assembly and vehicle body with the 6 bolts.

Torque:
Bolt (C) : 60 N*m (612 kgf*cm, 44 ft.*lbf)
Bolt (D) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)


g.
A455201N01
1.125,0.063 1.281,0.26 0.156,0.198 10 true A 0.906,0.365 1.063,0.563 0.156,0.198 10 true B 0.76,0.792 0.917,0.99 0.156,0.198 10 true C 0.698,1.094 0.854,1.292 0.156,0.198 10 true D

Install the engine mounting insulator sub-assembly LH to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Fully tighten the 4 bolts in the order of (A), (C), (B) and (D).



h.
A455202N01
1.896,0.479 2.052,0.677 0.156,0.198 10 true A 1.01,1.844 1.167,2.042 0.156,0.198 10 true B 0.865,1.146 1.021,1.344 0.156,0.198 10 true C 2.125,1.677 2.281,1.875 0.156,0.198 10 true C

Install the engine mounting stay LH to the engine mounting insulator sub-assembly LH with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 4 bolts in the order of (B), (C) and (A).



i.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 17410 23.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 58166A 24.INSTALL FRONT FLOOR COVER LH

a.

Engage the 5 clamps to install the front floor cover LH to the vehicle body with the 5 bolts, 3 screws and 3 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58165C 25.INSTALL FRONT FLOOR COVER RH

a.

Engage the 4 clamps to install the front floor cover RH to the vehicle body with the 3 bolts, 3 screws and clip.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 45220 26.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 16281N 27.CONNECT NO. 4 WATER BY-PASS HOSE

a.

Connect the No. 4 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.

A455226C01
1.833,1.635 1.99,1.833 0.156,0.198 10 true A 3.396,0.521 3.708,0.719 0.313,0.198 10 false *a 5.115,0.823 5.427,1.021 0.313,0.198 10 false *b 5.302,1.302 5.615,1.5 0.313,0.198 10 false *d 4.396,0.5 4.708,0.698 0.313,0.198 10 false *c 6.073,1.865 6.385,2.063 0.313,0.198 10 false *e
*a View A *b 120°
*c Upper Side *d Front Side
*e 2 to 7 mm (0.0787 to 0.276 in.) - -



Hide 28.CONNECT WIRE HARNESS

a.

Connect the earth wire with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the claw to connect the wire harness to the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Connect the 4 connectors to the No. 1 engine room relay block and No. 1 junction block assembly.


d.

Install the nut to the No. 1 engine room relay block and No. 1 junction block assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Engage the 3 claws and install the No. 1 relay block cover to the No. 1 engine room relay block and No. 1 junction block assembly.


Hide 32930F 29.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE ASSEMBLY

a.

Connect the outlet motor hose to the hybrid vehicle transaxle assembly and slide the clip to secure it.

A490176C02
0.208,1.49 2.063,2.542 1.854,1.052 6.698,1.708 6.594,1.708 6.594,1.708 6.323,1.875 false 5.844,1.958 5.5,2.365 5.5,2.365 5.354,2.365 true 0.677,2.042 0.906,2.25 0.906,2.25 1.052,2.25 true 0.531,2.042 0.479,2.219 0.479,2.219 0.417,2.219 true 2.99,1.104 2.99,0.792 true 3.281,1.802 3.49,1.542 3.49,1.542 3.667,1.542 true 6.438,0.479 6.75,0.677 0.313,0.198 10 false *a 6.438,0.938 6.75,1.135 0.313,0.198 10 false *a 5.938,1.323 6.25,1.521 0.313,0.198 10 false *b 5.969,2.333 6.281,2.531 0.313,0.198 10 false *c 6.75,1.604 7.063,1.802 0.313,0.198 10 false *d 5.198,2.271 5.51,2.469 0.313,0.198 10 false *e 4.958,1.813 5.271,2.01 0.313,0.198 10 false *f 5.438,0.708 5.75,0.906 0.313,0.198 10 false *f 0.813,1.5 1.125,1.698 0.313,0.198 10 false *b 0.698,2.354 1.01,2.552 0.313,0.198 10 false *c 1.104,2.146 1.417,2.344 0.313,0.198 10 false *e 0.271,2.125 0.583,2.323 0.313,0.198 10 false *e 0.927,0.385 1.083,0.583 0.156,0.198 10 true A 0.25,1.51 0.563,1.708 0.313,0.198 10 false *g 1.531,2.292 1.844,2.49 0.313,0.198 10 false *h 2.927,1.146 3.24,1.344 0.313,0.198 10 true *1 3.74,1.438 4.052,1.635 0.313,0.198 10 true *2
*1 Inlet Motor Hose *2 Outlet Motor Hose
*a 45° (Claw of Clip Location) *b 2 to 7 mm (0.0787 to 0.276 in.)
*c 0 to 3 mm (0 to 0.118 in.) *d Marking
*e Paint Mark *f Center of Paint Mark
*g View A *h 360° (Claw of Clip Location)



b.

Connect the inlet motor hose to the hybrid vehicle transaxle assembly and slide the clip to secure it.


c.

Engage the clamp.


Hide G9229A 30.CONNECT NO. 5 INVERTER COOLING HOSE

a.

Connect the No. 5 inverter cooling hose to the motor cooling cooler and slide the clip to secure it.

A455221C01
4.688,0.667 4.969,1.25 true 2.552,1.365 2.708,1.563 0.156,0.198 10 true A 3.948,0.313 4.26,0.51 0.313,0.198 10 false *a 5.323,0.708 5.635,0.906 0.313,0.198 10 false *b 4.063,1.479 4.375,1.677 0.313,0.198 10 false *e 4.917,0.583 5.229,0.781 0.313,0.198 10 false *d 4.542,0.49 4.854,0.688 0.313,0.198 10 false *c
*a View A *b 120°
*c Paint Mark *d Upper Side
*e Front Side - -



Hide 88703 32.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the discharge hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the discharge hose sub-assembly.

NOTICE:
·

Keep the O-ring and O-ring fitting surface free of foreign matter.

·

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.




d.

Connect the discharge hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 16572D 33.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet with thermostat sub-assembly and slide the clip to secure it.

A455222C01
3.844,0.667 4.125,1.271 true 1.271,1.781 1.427,1.979 0.156,0.198 10 true A 3.156,0.354 3.469,0.552 0.313,0.198 10 false *a 4.521,0.781 4.833,0.979 0.313,0.198 10 false *b 3.25,1.479 3.563,1.677 0.313,0.198 10 false *e 4.063,0.594 4.375,0.792 0.313,0.198 10 false *d 3.708,0.417 4.021,0.615 0.313,0.198 10 false *c 5.813,1.813 6.125,2.01 0.313,0.198 10 false *f
*a View A *b 120°
*c Paint Mark *d Upper Side
*e RH Side *f 2 to 7 mm (0.0787 to 0.276 in.)



Hide 16571C 34.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.

A455223C01
3.844,0.688 4.125,1.24 false 2.01,0.948 2.167,1.146 0.156,0.198 10 true A 3.167,0.385 3.479,0.583 0.313,0.198 10 false *a 4.531,0.802 4.844,1 0.313,0.198 10 false *b 3.219,1.521 3.531,1.719 0.313,0.198 10 false *e 4.063,0.667 4.375,0.865 0.313,0.198 10 false *d 5.677,1.979 5.99,2.177 0.313,0.198 10 false *f 3.698,0.49 4.01,0.688 0.313,0.198 10 false *c
*a View A *b 120°
*c Paint Mark *d Front Side
*e RH Side *f 2 to 7 mm (0.0787 to 0.276 in.)



b.

Engage the clamp.


Hide 23901 35.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly.

i.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION



b.

Install the EFI fuel pipe clamp to the fuel tube connector.


Hide 87245B 36.CONNECT INLET HEATER WATER HOSE B

a.
A403462C02
1.01,0.979 1.438,0.979 false 1.875,0.969 2.302,0.969 false 1.021,1.354 1.448,1.354 false 1.844,1.365 2.281,1.917 2.281,1.917 2.594,1.917 false 0.813,0.885 1.125,1.042 0.313,0.156 10 false *a 0.833,1.271 1.146,1.427 0.313,0.156 10 false *b 2.365,0.896 2.677,1.052 0.313,0.156 10 false *a 2.635,1.844 2.948,2 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusions of the inlet heater water hose B connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and securely insert the inlet heater water hose B connector into the stopper of the pipe.


b.
A455224C01
1.583,1.354 1.063,1.25 1.063,1.25 0.865,1.25 true 0.552,1.135 0.833,1.333 0.281,0.198 10 true *a
*a Retainer
V113147

Push
V113148

Push in


Push in the retainer.


c.

Check that the flow shutting valve (water by-pass hose assembly) and inlet heater water hose B connector are securely connected by pulling on them.


Hide 87246B 37.CONNECT OUTLET HEATER WATER HOSE B

a.
A403463C02
1.052,1.156 1.573,1.156 false 0.99,0.365 1.219,0.365 1.219,0.365 1.521,0.792 false 0.875,1.063 1.188,1.219 0.313,0.156 10 false *a 0.823,0.281 1.135,0.438 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater water hose B connector and securely insert the outlet heater water hose B connector into the stopper of the pipe.


b.
A455225C01
1.583,1.656 1.802,1.656 1.802,1.656 2.094,1.375 true 1.302,1.552 1.552,1.76 0.25,0.208 10 true *a
*a Retainer
V113147

Push
V113148

Push in


Push in the retainer.


c.

Check that the No. 2 water by-pass pipe sub-assembly and outlet heater water hose B connector are securely connected by pulling on them.


Hide 23820 38.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.

Connect the fuel vapor feed hose assembly to the No. 1 vacuum switching valve assembly.


b.

Engage the clamp.


Hide G9200 39.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 52132A 40.INSTALL NO. 2 FRONT BUMPER REINFORCEMENT

Hide 52618 41.INSTALL FRONT BUMPER LOWER ABSORBER

Hide 45.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 56.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 57.INSTALL HEADLIGHT ASSEMBLY LH

Hide 53737B 58.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53736 59.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51420 60.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

a.

Install the No. 2 engine under cover assembly with the 2 bolts, 2 screws and 6 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 61.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 3 bolts, 8 screws and 2 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53852B 62.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

a.

Install the front wheel opening extension pad LH with the 4 screws.


Hide 53851D 63.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

a.

Install the front wheel opening extension pad RH with the 4 screws.


Hide 12601B 64.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A455227

Engage the 3 clips to install the No. 1 engine cover sub-assembly.

NOTICE:
·

Securely engage the clips.

·

If the clips are forcibly engaged or struck with an object, they may be damaged.




Hide 65.INSTALL FRONT WHEELS

Hide 66. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 67.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT