Home › Drivetrain › Q610 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE SIDE GEAR OIL SEAL
RM37A0E _52 Drivetrain _086904 Q610 HYBRID TRANSMISSION / TRANSAXLE _0420901 HYBRID TRANSAXLE SIDE GEAR OIL SEAL A

Q610 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE SIDE GEAR OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear drive shaft oil seal LH or rear drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: If the vehicle height has changed due to suspension or tire replacement

*2: for RH Side

Rear wheel alignment adjustment Perform "Calibration"
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.*1
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leaks from exhaust system*2 Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 42340D 2.REMOVE REAR DRIVE SHAFT OIL SEAL LH

a.
C426461N01
2.417,1.688 2.594,0.906 2.594,0.906 2.729,0.906 true 2.771,0.813 3.167,1.052 0.396,0.24 10 true SST

Using SST, remove the rear drive shaft oil seal LH from the rear traction motor with transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the rear traction motor with transaxle assembly.



Hide 42330G 3.REMOVE REAR DRIVE SHAFT OIL SEAL RH

a.
C426462C01
1.573,3.063 1.573,2.635 true 1.448,3.073 1.802,3.281 0.354,0.208 10 true SST 0.26,2.49 0.458,2.729 0.198,0.24 10 true *a
*a Hold
V113147

Turn


Using SST, remove the rear drive shaft oil seal RH from the rear traction motor with transaxle assembly.

SST
09612-65014  (09612-01020)

NOTICE:

Be careful not to damage the rear traction motor with transaxle assembly.



Hide 42330G 4.INSTALL REAR DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new rear drive shaft oil seal RH with a small amount of MP grease.


b.
C426463C01
2.635,1.063 2.635,0.938 2.635,0.938 2.594,0.823 false 2.365,1.073 2.365,0.885 2.365,0.885 2.417,0.75 false 1.729,2.74 0.906,2.896 0.906,2.896 1.49,2.302 true 2.719,0.115 2.969,0.354 0.25,0.24 10 false *a 2.563,1.073 2.75,1.281 0.188,0.208 10 false *b 2.281,1.063 2.5,1.281 0.219,0.219 10 false *c 0.552,2.823 0.875,3.052 0.323,0.229 10 true SST
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install the rear drive shaft oil seal RH to the rear traction motor with transaxle assembly.

SST
09316-20011  
09517-30010  

Standard Depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)


NOTICE:
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


·

Make sure that the outer lip of the rear drive shaft oil seal RH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the rear drive shaft oil seal RH.

·

Do not install the rear drive shaft oil seal RH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the rear drive shaft oil seal RH.




Hide 42340D 5.INSTALL REAR DRIVE SHAFT OIL SEAL LH

a.

Coat the lip of a new rear drive shaft oil seal LH with a small amount of MP grease.


b.
C426464C01
1.896,2.76 2.625,2.896 2.625,2.896 2.167,2.365 true 1.104,0.99 1.104,0.854 1.104,0.854 1.063,0.729 false 0.813,0.979 0.813,0.854 0.813,0.854 0.885,0.76 false 2.667,2.823 3.01,3.042 0.344,0.219 10 true SST 1.208,0.104 1.458,0.323 0.25,0.219 10 false *a 0.75,1 0.969,1.25 0.219,0.25 10 false *b 1.042,1.01 1.281,1.229 0.24,0.219 10 false *c
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install the rear drive shaft oil seal LH to the rear traction motor with transaxle assembly.

SST
09316-20011  
09517-30010  

Standard Depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)


NOTICE:
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


·

Make sure that the outer lip of the rear drive shaft oil seal LH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the rear drive shaft oil seal LH.

·

Do not install the rear drive shaft oil seal LH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the rear drive shaft oil seal LH.