Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for LHD)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420936 BRAKE PEDAL STROKE SENSOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for LHD)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



a.

When installing a new brake pedal stroke sensor assembly:

NOTICE:

Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the 2 nuts.


i.
C425580C01
2.5,0.604 2.5,0.271 2.5,0.271 2.833,0.271 true 2.688,0.792 2.688,0.958 2.688,0.958 3.021,0.958 true 0.885,0.667 1.219,0.667 true 0.896,4.198 0.896,3.865 false 2.844,0.188 3.031,0.385 0.188,0.198 10 true *a 3.042,0.875 3.229,1.073 0.188,0.198 10 true *b 0.74,0.573 0.927,0.771 0.188,0.198 10 true *c 2.198,4.271 2.385,4.469 0.188,0.198 10 true *d 0.76,4.219 1.125,4.458 0.365,0.24 10 true SST 1.104,1.615 1.24,1.792 0.135,0.177 10 true B 1.135,3.104 1.271,3.281 0.135,0.177 10 true A
*a Brake Pedal Stroke Sensor Assembly Lever
*b Brake Pedal Groove
*c Brake Pedal Stroke Sensor Assembly Lever Set Pin
*d Torque Wrench Fulcrum Length


Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Fully tighten the nut (A).

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


iii.

Using SST, fully tighten the nut (B).

SST
09961-00950  

Torque:
Specified tightening torque : 8.5 N*m (87 kgf*cm, 75 in.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 185 mm (7.28 in.)):

4.7 N*m (48 kgf*cm, 42 in.*lbf)




iv.

Connect the connector.


v.

Firmly depress the brake pedal to break the brake pedal stroke sensor assembly lever set pin.


vi.

Remove the broken lever set pin.



b.

When reusing the brake pedal stroke sensor assembly:

i.
C425581C01
3.01,0.969 2.677,0.969 2.677,0.969 2.677,0.802 true 2.906,0.26 2.49,0.26 2.49,0.26 2.49,0.625 true 2.917,0.177 3.146,0.365 0.229,0.188 10 true *a 3.021,0.875 3.229,1.052 0.208,0.177 10 true *b
*a Brake Pedal Stroke Sensor Assembly Lever
*b Brake Pedal Groove


Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 nuts.

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 89510D 4.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
·

When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.

·

Do not depress the brake pedal after turning the ignition switch to ON.



a.
C425582C01
0.917,3 0.917,2.667 false 0.792,3.01 1.24,3.26 0.448,0.25 10 false SST 2.198,3.052 2.646,3.302 0.448,0.25 10 false *a 0.813,1.938 0.958,2.104 0.146,0.167 10 true A 0.823,0.469 0.969,0.635 0.146,0.167 10 true B
*a Torque Wrench Fulcrum Length


Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207
Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



b.

Fully tighten the nut (A).

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Using SST, fully tighten the nut (B).

SST
09961-00950  

Torque:
Specified tightening torque : 8.5 N*m (87 kgf*cm, 75 in.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 185 mm (7.28 in.)):

4.7 N*m (48 kgf*cm, 42 in.*lbf)




Hide 5.PERFORM INITIALIZATION AND CALIBRATION