Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for HV Model LHD) › 2020.02–2020.11
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0420921 BRAKE PEDAL(for HV Model) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for HV Model)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Remove the front door scuff plate LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


b.

Remove the cowl side trim sub-assembly LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL




e.

Check the brake pedal height.

HINT:

Inspect and adjust the brake pedal height with the floor carpet and front floor mat folded back.


i.

Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.

C425726C02
5.177,2.885 5.427,2.885 5.427,2.885 5.719,2.531 true 1.698,2.354 1.698,2.031 true 6.115,1.406 6.323,1.115 6.323,1.115 6.615,1.115 false 2.24,3 2.24,2.677 true 2.229,1.813 2.396,1.396 2.396,1.396 2.729,1.396 true 1.615,2.375 1.792,2.542 0.177,0.167 10 true *1 2.771,2.115 2.958,2.292 0.188,0.177 10 true *a 5.021,2.802 5.333,2.958 0.313,0.156 10 false *b 0.708,1.563 0.896,1.74 0.188,0.177 10 true *d 6.656,1.031 6.865,1.198 0.208,0.167 10 false *1 6.323,2.104 6.625,2.396 0.302,0.292 10 false *a 2.156,3.01 2.333,3.177 0.177,0.167 10 true *b 2.76,1.302 2.948,1.479 0.188,0.177 10 true *c
*1 Brake Pedal Pad - -
*a Brake Pedal Height *b Measuring Plane of Floor Panel
*c Ruler *d 36 mm (1.42 in.)


Brake Pedal Height from Floor Panel:

155.6 to 171.6 mm (6.13 to 6.76 in.)


HINT:

If the brake pedal height is not as specified, inspect and adjust the push rod length according to the procedure below.




f.

Adjust the push rod length.

i.
C426258C01
1.75,4.313 2.135,4.313 2.135,4.313 2.469,3.948 true 2.854,1.906 2.854,1.406 2.854,1.406 3.021,1.406 false 2.156,1.677 2.156,0.677 2.156,0.677 2.573,0.677 false 3.063,1.333 3.323,1.708 0.26,0.375 10 false *1 2.625,0.604 2.948,0.875 0.323,0.271 10 false *2 1.583,4.229 1.896,4.385 0.313,0.156 10 false *a 2.958,3.635 3.313,3.969 0.354,0.333 10 false *b
*1 Stop Light Switch Assembly
*2 Lock Nut
*a Floor Panel
*b Brake Pedal Height


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height from Floor Panel:

155.6 to 171.6 mm (6.13 to 6.76 in.)



iv.

Tighten the lock nut.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION





i.

Install the cowl side trim sub-assembly LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


j.

Install the front door scuff plate LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:

Do not depress the brake pedal after turning the ignition switch to ON.


a.

Inspect the brake pedal stroke sensor assembly.

i.

Read the stroke sensor value without the brake pedal depressed.

Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207
Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V


HINT:

If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.




b.

Adjust the brake pedal stroke sensor assembly.

i.
C425443

Loosen the 2 nuts.


ii.
C425582C01
0.917,3 0.917,2.667 false 0.792,3.01 1.24,3.26 0.448,0.25 10 false SST 2.198,3.052 2.646,3.302 0.448,0.25 10 false *a 0.813,1.938 0.958,2.104 0.146,0.167 10 true A 0.823,0.469 0.969,0.635 0.146,0.167 10 true B
*a Torque Wrench Fulcrum Length


Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



iii.

Fully tighten the nut (A).

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


iv.

Using SST, fully tighten the nut (B).

SST
09961-00950  

Torque:
Specified tightening torque : 8.5 N*m (87 kgf*cm, 75 in.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 185 mm (7.28 in.)):

4.7 N*m (48 kgf*cm, 42 in.*lbf)






Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708C09
2.167,1.563 2.469,1.781 0.302,0.219 10 false *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


HINT:
·

If the brake pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

·

If the brake pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.




Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

With the ignition switch ON (READY), depress the brake pedal and measure the brake pedal reserve distance.

C425728C01
4.51,2.354 4.844,2.354 4.844,2.354 4.969,1.792 true 2.365,2.698 2.365,2.344 true 5.615,1.479 5.823,1.229 5.823,1.229 6.073,1.229 false 0.573,1.885 0.99,1.885 true 0.938,1.25 1.188,1.25 1.188,1.25 1.385,1.854 true 2.292,2.719 2.469,2.885 0.177,0.167 10 true *1 1.333,2.688 1.51,2.865 0.177,0.177 10 true *a 3.333,1.667 3.51,1.833 0.177,0.167 10 true *d 6.104,1.146 6.448,1.438 0.344,0.292 10 false *1 5.552,2.729 5.969,3.188 0.417,0.458 10 false *a 4.344,2.271 4.74,2.604 0.396,0.333 10 false *b 0.396,1.802 0.573,1.979 0.177,0.177 10 true *b 0.76,1.156 0.938,1.333 0.177,0.177 10 true *c
*1 Brake Pedal Pad - -
*a Brake Pedal Reserve Distance *b Measuring Plane of Floor Panel
*c Ruler *d 36 mm (1.42 in.)


Brake Pedal Reserve Distance from Floor Panel at 300 N (31 kgf, 67.4 lbf):

91 mm (3.58 in.) or more


HINT:

If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM (for HV Model)>PROBLEM SYMPTOMS TABLE