Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C143A7E  ABS Solenoid Control Module Actuator Stuck On  C143A7F  ABS Solenoid Control Module Actuator Stuck Off  


DESCRIPTION

The ABS solenoid relay is built into the skid control ECU in the brake actuator assembly.

The ABS solenoid relay supplies power to the holding solenoid and reduction solenoid.

The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by self-diagnosis performed when the vehicle is starting off.

DTC No. Detection Item DTC Detection Condition Trouble Area
C143A7E ABS Solenoid Control Module Actuator Stuck On When voltage at terminal +BS is 9.5 V or higher, solenoid relay is OFF, relay contact is ON continuously for 4.5 seconds or more. Skid control ECU (brake actuator assembly)
C143A7F ABS Solenoid Control Module Actuator Stuck Off When voltage at terminal +BS is 9.5 V or higher and solenoid relay is ON, relay contact is OFF continuously for 0.22 seconds or more.
·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C322503E32
0.156,1.167 1.01,1.865 0.854,0.698 10 false from Auxiliary Battery 1.542,1.375 2.458,1.573 0.917,0.198 10 false ABS NO. 2 1.573,1.115 1.76,1.333 0.188,0.219 10 false 1 2.01,1.104 2.198,1.323 0.188,0.219 10 false 2 4.573,0.875 5.479,1.427 0.906,0.552 10 false ABS Solenoid Relay 4.438,3.365 5.615,3.708 1.177,0.344 10 false Skid Control ECU 3.51,1.323 3.917,1.51 0.406,0.188 10 false +BS 3.26,1.083 3.531,1.281 0.271,0.198 10 false 14 3.51,5.208 3.917,5.396 0.406,0.188 10 false GND1 3.323,4.948 3.594,5.146 0.271,0.198 10 false 1 4.354,7.844 4.76,8.031 0.406,0.188 10 false A39 4.354,8.01 6.115,8.219 1.76,0.208 10 false Brake Actuator Assembly 5.969,1.74 6.458,1.948 0.49,0.208 10 false SFRH 5.969,2.229 6.458,2.438 0.49,0.208 10 false SFLH 5.969,2.74 6.458,2.948 0.49,0.208 10 false SRRH 5.958,3.229 6.448,3.438 0.49,0.208 10 false SRLH 5.979,3.729 6.469,3.938 0.49,0.208 10 false SFRR 5.969,4.24 6.458,4.448 0.49,0.208 10 false SFLR 5.969,4.74 6.458,4.948 0.49,0.208 10 false SRRR 5.969,5.24 6.458,5.448 0.49,0.208 10 false SRLR 6.01,5.74 6.5,5.948 0.49,0.208 10 false SM1 6,6.25 6.49,6.458 0.49,0.208 10 false SM2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY



HINT:

When C137BA2 and/or C137BA3 is output together with C143A7E and/or C143A7F, inspect and repair the trouble areas indicated by C137BA2 and/or C137BA3 first.

for C137BA2: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>C137BA2

for C137BA3: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>C137BA3


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
C343081C65
1.49,0.146 1.854,0.406 0.365,0.26 2.896,1.823 2.646,0.979 true 1.542,0.188 2,0.385 0.458,0.198 10 false A39 0.167,0.188 0.625,0.385 0.458,0.198 10 false *a 2.792,1.865 3.25,2.063 0.458,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-1 (GND1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs C143A7E and C143A7F are not output. A
DTCs C143A7E and/or C143A7F are output. B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch turned to ON and the stop light switch assembly off, the ECU performs self-diagnosis of the solenoid circuit.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harnesses, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.




A

B