The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (electric parking brake switch assembly) is pressed while the ignition switch is ON.
Conditions required for operation standby:
The driver door is closed.
The driver seat belt is fastened.
The system is normal.
If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.
Brake system
Electric parking brake system
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.
The driver door is closed.
The driver seat belt is fastened.
The system is normal.
If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.
Brake system
Electric parking brake system
| Proceed to |
|---|
| NEXT |
NEXT
Check the brake hold standby indicator light and mode condition on the GTS changes according to brake hold switch (electric parking brake switch assembly) operation.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Hold Ready | Brake hold control permission status | Not in stand-by mode / Stand-by mode | Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated) |
- |
| Tester Display |
|---|
| Brake Hold Ready |
| Brake Hold Switch (Electric Parking Brake Switch Assembly) Operation | Mode Condition Display | Brake Hold Standby Indicator Light |
|---|---|---|
| Not pressed | Not in stand-by mode | Does not come on |
| Pressing the brake hold switch (electric parking brake switch assembly) | Stand-by mode | Come on |
| Result | Proceed to |
|---|---|
| Indicator light and mode condition display do not change | A |
| Mode condition display is normal, but indicator light does not change | B |
| Indicator light and mode condition display are normal | C |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Inspect the brake hold switch (electric parking brake switch assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE HOLD SWITCH>INSPECTION
The brake hold switch (electric parking brake switch assembly) operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P2-10 (SLT1) - A39-35 (PKB) | Always | Below 1 Ω |
| P2-10 (SLT1) or A39-35 (PKB) - Body ground | Always | 10 kΩ or higher |
| P2-12 (E) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
NG