Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  Downhill Assist Control Indicator Light Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The downhill assist control indicator light comes on when the downhill assist control is ready. Even if the downhill assist control switch is pressed, the downhill assist control indicator light will blink and the downhill assist control will not be activated under the following conditions:

·

The shift lever is in any position other than S (1st) or R.

·

The vehicle speed is 30 km/h (18 mph) or more.

·

VSC system is malfunctioning.

·

Temperature of the brake actuator assembly increases and the downhill assist control is temporarily canceled.


WIRING DIAGRAM

C427345E04
5.365,0.917 5.979,1.115 0.615,0.198 10 false CANL 5.375,1.74 5.99,1.938 0.615,0.198 10 false CANH 5.094,0.76 5.708,0.958 0.615,0.198 10 false 43 5.094,1.563 5.708,1.76 0.615,0.198 10 false 27 5.365,2.99 5.979,3.313 0.615,0.323 10 false HDCS 5.094,2.75 5.708,2.948 0.615,0.198 10 false 44 3.208,3.385 5.313,3.75 2.104,0.365 10 false Downhill Assist Control Switch 3.219,3.219 3.833,3.417 0.615,0.198 10 false P4 3.656,2.979 4.271,3.177 0.615,0.198 10 false E 4.354,2.99 4.969,3.188 0.615,0.198 10 false B 4.531,2.771 5.146,2.969 0.615,0.198 10 false 5 3.479,2.771 4.083,3.052 0.604,0.281 10 false 2 2.938,4.333 5.042,4.698 2.104,0.365 10 false : CAN Communication Line 0.146,3.927 0.76,4.125 0.615,0.198 10 false H21 0.135,4.104 2.208,4.396 2.073,0.292 10 false Combination Meter Assembly 0.906,0.927 1.521,1.125 0.615,0.198 10 false CANL 0.906,1.74 1.521,1.938 0.615,0.198 10 false CANH 4.979,4.104 6.573,4.594 1.594,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 4.99,3.917 5.604,4.24 0.615,0.323 10 false A39 1.396,1.573 1.938,1.885 0.542,0.313 10 false 32 1.396,0.74 1.938,1.052 0.542,0.313 10 false 31

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY


PROCEDURE

1.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SWITCH)
a.

Check the downhill assist control indicator and mode condition on the GTS changes according to downhill assist control switch operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Downhill Assist Control SW Downhill assist control switch OFF / ON - -
Chassis > Brake/EPB > Data List
Tester Display
Downhill Assist Control SW
50003 435 58
Standard:
Downhill Assist Control Switch Operation Mode Condition Display Downhill Assist Control Indicator Light
Not pressed OFF Does not come on
Pressing the downhill assist control switch ON Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change A
Mode condition display is normal, but indicator light does not change B
Indicator light and mode condition display are normal C



A

2.INSPECT DOWNHILL ASSIST CONTROL SWITCH

B

C

2.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.

Turn the ignition switch off.


b.

Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-44 (HDCS) - P4-5 (B) Always Below 1 Ω
A39-44 (HDCS) or P4-5 (B) - Body ground Always 10 kΩ or higher
P4-2 (E) - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR