When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.
Pre-collision brake is operating.*
The dynamic radar cruise control system is operating and is applying the brakes.*
Secondary collision brake is operating.*
Brake hold is operating.
The parking brake is engaged while the vehicle is being driven.
Downhill assist control is operating.
*: w/ Pre-collision System
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C13807E | Stop Lamp Relay Actuator Stuck On | When the IG1 terminal voltage exceeds 10 V and the +BS terminal voltage is 9.5 V or higher, stop light drive output (STPO) is OFF, STP2 is OFF and STP is ON continuously for 5 seconds or more. | ·
Wire harness and connector ·
Stop light switch assembly ·
Skid control ECU (brake actuator assembly) ·
STP circuit ·
STP2 circuit |
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
When DTC P057111 and/or P057113 are output together with DTC C13807E, inspect and repair the trouble areas indicated by DTC P057111 and/or P057113 first.
for P057111: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>P057111
for P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>P057113
With the brake pedal released, check the illumination status of the brake lights.
| Result | Proceed to |
|---|---|
| The stop lights are illuminated. | A |
| The stop lights are not illuminated. | B |
A
B
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-11 (STP) - Body ground | Stop light switch assembly off
(Brake pedal released) |
Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A42 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-11 (STP) - Body ground | Always | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that there is no short to +B in the STP circuit (wire harnesses, connectors and stop lights).
No short to +B.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-37 (STP2) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
NG
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-3 (L) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that there is no short to ground in the STP2 circuit (wire harnesses, connectors and ECUs)
There is no short to ground.
| Proceed to |
|---|
| OK |
| NG |
OK
NG