Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  P057111  Brake Switch "A" Circuit Short to Ground  


DESCRIPTION

The skid control ECU (brake actuator assembly) inputs the stop light signal and brake operation condition.

When the brake pedal is depressed and the stop light switch signal is not input, this DTC is output.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057111 Brake Switch "A" Circuit Short to Ground Either of the following is detected:
·

When the +BS terminal voltage is 9.5 V or higher and the brake pedal load sensing switch (brake pedal support assembly) is ON, the stop light switch signal is not input continuously for 2 seconds or more with the master cylinder pressure at 2 MPa (20.4 kgf/cm2) or higher and the deceleration calculated from the vehicle speed at 0.2 G or higher.

·

After a master cylinder pressure of more than 1.764 MPa (18.0 kgf/cm2) is detected for 5 seconds or more continuously at a vehicle speed below 3 km/h (2 mph) with the stop light switch assembly off, the master cylinder pressure exceeds 1.764 MPa (18.0 kgf/cm2) for 1 second or more continuously while and the stop light switch assembly signal is not received when the vehicle decelerates from over 35 km/h (22 mph) to 3 km/h (2 mph).


·

Stop light switch assembly

·

Wire harness and connector

·

Brake pedal load sensing switch (brake pedal support assembly)

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY



PROCEDURE

1.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model LHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and the pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and stop light switch assembly before inspecting the input signals and other related parts.


Result:
Proceed to
OK
NG



OK

2.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STOP LIGHT SW AND BRAKE PEDAL LOAD SENSING SWITCH)

NG

11.INSPECT STOP LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (STOP LIGHT SW AND BRAKE PEDAL LOAD SENSING SWITCH)
a.

Check that the stop light switch display and brake pedal load sensing switch (brake pedal support assembly) display observed on the GTS change according to brake pedal operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed.



Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake pedal support assembly) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > Brake/EPB > Data List
Tester Display
Stop Light SW
Brake Pedal Load Sensing SW
50003 435 59,61
OK:

The GTS displays OFF / ON according to brake pedal operation.



b.

Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch (brake pedal support assembly) turn on.

OK:

First the stop light switch assembly turns on, and then the brake pedal load sensing switch (brake pedal support assembly) turns on.



Result:
Result Proceed to
OK A
NG (The stop light switch assembly does not turn on.) B
NG (Turning on of the brake pedal load sensing switch (brake pedal support assembly) is not confirmed.) C
NG (The brake pedal load sensing switch (brake pedal support assembly) turns on first.) D



A

4.CLEAR DTC

B

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

C

10.CHECK HARNESS AND CONNECTOR (BRAKE PEDAL SUPPORT ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

D

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

4.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC P057111 is not output. A
DTC P057111 is output. B



A

B

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C343081C58
1.49,0.146 1.854,0.406 0.365,0.26 2.021,0.938 2.406,0.396 true 1.552,0.188 2.01,0.385 0.458,0.198 10 false A39 0.167,0.188 0.625,0.385 0.458,0.198 10 false *a 2.292,0.229 2.75,0.427 0.458,0.198 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-11 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A39-11 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.

Reconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.RECONFIRM DTC
8.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC P057111 is not output. A
DTC P057111 is output. B



A

9.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

B

9.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
a.

Turn the ignition switch off.


b.

Inspect the brake pedal load sensing switch (brake pedal support assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL LOAD SENSING SWITCH>ON-VEHICLE INSPECTION

OK:

The brake pedal load sensing switch (brake pedal support assembly) is normal.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BRAKE PEDAL SUPPORT ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (BRAKE PEDAL SUPPORT ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A45 brake pedal load sensing switch (brake pedal support assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-2 (FSW+) - A39-28 (FSW+) Always Below 1 Ω
A45-2 (FSW+) or A39-28 (FSW+) - Body ground Always 10 kΩ or higher
A45-1 (FSW-) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT STOP LIGHT SWITCH ASSEMBLY

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C343081C58
1.49,0.146 1.854,0.406 0.365,0.26 2.021,0.938 2.406,0.396 true 1.552,0.188 2.01,0.385 0.458,0.198 10 false A39 0.167,0.188 0.625,0.385 0.458,0.198 10 false *a 2.292,0.229 2.75,0.427 0.458,0.198 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-11 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A39-11 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

13.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CLEAR DTC
a.

Reconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

14.RECONFIRM DTC
14.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC P057111 is not output. A
DTC P057111 is output. B



A

B