Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P070562  Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure  


DESCRIPTION

The shift lever position sensor sends 7 different switch signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses these signals to detect the shift lever position (P, R, N or D). The hybrid vehicle control ECU also uses this information to determine the intended direction of travel (forward or reverse).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P070562 Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure Shift sensor circuit malfunction (abnormal pattern)
A malfunction in the P, R, N or D circuit is detected based on the shift sensor input pattern.
(1 trip detection logic)
·

Wire harness or connector

·

Shift lever position sensor

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P070562
·

Shift Position

·

Shift Position Sensor (PNB)

·

Shift Position Sensor (PR)

·

Shift Position Sensor (DB1)

·

Shift Position Sensor (DB2)

·

Shift Position Sensor (N)

·

Shift Position Sensor (R)

·

Shift Position Sensor (P)



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Slowly move the shift lever from P to S then back to P.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A407614E18
0.531,4 1.208,4.51 0.677,0.51 10 false C53 0.521,4.156 2.99,4.469 2.469,0.313 10 false Shift Lever Position Sensor 1.896,0.583 2.208,0.781 0.313,0.198 10 false +B 1.969,1.083 2.281,1.281 0.313,0.198 10 false P 1.958,1.438 2.271,1.635 0.313,0.198 10 false R 1.969,1.813 2.281,2.01 0.313,0.198 10 false N 1.844,2.135 2.156,2.333 0.313,0.198 10 false DB1 1.896,2.823 2.208,3.021 0.313,0.198 10 false PR 1.833,3.198 2.146,3.396 0.313,0.198 10 false PNB 1.833,2.479 2.146,2.677 0.313,0.198 10 false DB2 2.188,0.583 2.5,0.781 0.313,0.198 10 false 7 2.208,1.083 2.521,1.281 0.313,0.198 10 false 8 2.208,1.438 2.521,1.635 0.313,0.198 10 false 9 2.198,1.813 2.51,2.01 0.313,0.198 10 false 2 2.198,2.135 2.51,2.333 0.313,0.198 10 false 1 2.198,2.479 2.51,2.677 0.313,0.198 10 false 6 2.208,2.813 2.521,3.01 0.313,0.198 10 false 3 2.198,3.198 2.51,3.396 0.313,0.198 10 false 4 4.552,0.563 4.865,0.76 0.313,0.198 10 false 18 4.563,1.063 4.875,1.26 0.313,0.198 10 false 28 4.625,1.417 4.938,1.615 0.313,0.198 10 false 2 4.563,1.802 4.875,2 0.313,0.198 10 false 29 4.625,2.125 4.938,2.323 0.313,0.198 10 false 3 4.542,2.479 4.854,2.677 0.313,0.198 10 false 15 4.542,2.802 4.854,3 0.313,0.198 10 false 16 4.552,3.177 4.865,3.375 0.313,0.198 10 false 30 4.865,0.688 5.469,0.917 0.604,0.229 10 false PSFT 4.844,1.073 5.448,1.302 0.604,0.229 10 false P 4.844,1.417 5.156,1.615 0.313,0.198 10 false R 4.833,1.802 5.146,2 0.313,0.198 10 false N 4.833,2.125 5.146,2.323 0.313,0.198 10 false DB1 4.823,2.458 5.135,2.656 0.313,0.198 10 false DB2 4.823,2.802 5.135,3 0.313,0.198 10 false PR 4.813,3.167 5.125,3.365 0.313,0.198 10 false PNB 4.844,4.031 5.521,4.5 0.677,0.469 10 false A31 4.844,4.198 6.896,4.698 2.052,0.5 10 false Hybrid Vehicle Control ECU

PROCEDURE

1.READ VALUE USING GTS (SHIFT POSITION SENSOR)
a.

While slowly moving the shift lever from P to S, then back to P, read the Data List (Shift Position Sensor) displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display
Shift Position Sensor (PNB)
Shift Position Sensor (PR)
Shift Position Sensor (DB1)
Shift Position Sensor (DB2)
Shift Position Sensor (N)
Shift Position Sensor (R)
Shift Position Sensor (P)
50003 397 400,401,403,402,404,405,406
HINT:

Be sure to move the shift lever slowly.


Standard:
Data List Shift Position
P R N D or S
Shift Position Sensor (P) ON OFF OFF OFF
Shift Position Sensor (R) OFF ON OFF OFF
Shift Position Sensor (PR) ON ON OFF OFF
Shift Position Sensor (N) OFF OFF ON OFF
Shift Position Sensor (DB1) OFF OFF OFF ON
Shift Position Sensor (DB2) OFF OFF OFF ON
Shift Position Sensor (PNB) ON OFF ON OFF



b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
OK:

DTC P070562 is not output.



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK FOR INTERMITTENT PROBLEMS

NG

3.INSPECT SHIFT LEVER POSITION SENSOR
2.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

3.INSPECT SHIFT LEVER POSITION SENSOR
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

C407546C74
1.448,0.229 1.792,0.479 0.344,0.25 2.354,1.219 3.219,0.625 true 1.583,1.49 0.875,2.188 true 2.24,1.313 3.271,2.313 true 1.885,1.385 2.583,2.188 true 1.854,1.49 2.313,2.365 true 1.76,1.385 1.885,2.229 true 1.708,1.49 1.292,2.375 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 1.51,0.26 1.969,0.458 0.458,0.198 10 false A31 3.281,2.323 3.604,2.51 0.323,0.188 10 false DB1 3.281,0.479 3.49,0.667 0.208,0.188 10 false R 2.313,2.406 2.521,2.594 0.208,0.188 10 false P 2.583,2.198 2.906,2.385 0.323,0.188 10 false DB2 1.813,2.271 2.135,2.458 0.323,0.188 10 false PR 1.229,2.406 1.438,2.594 0.208,0.188 10 false N 0.688,2.219 1.021,2.406 0.333,0.188 10 false PNB
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A31-28 (P) - Body ground Ignition switch ON
Shift lever in P
6.0 to 14 V
Ignition switch ON
Shift lever in any position except P
0 to 1.5 V
A31-2 (R) - Body ground Ignition switch ON
Shift lever in R
6.0 to 14 V
Ignition switch ON
Shift lever in any position except R
0 to 1.5 V
A31-29 (N) - Body ground Ignition switch ON
Shift lever in N
6.0 to 14 V
Ignition switch ON
Shift lever in any position except N
0 to 1.5 V
A31-3 (DB1) - Body ground Ignition switch ON
Shift lever in D or S
6.0 to 14 V
Ignition switch ON
Shift lever in any position except D or S
0 to 1.5 V
A31-15 (DB2) - Body ground Ignition switch ON
Shift lever in D or S
6.0 to 14 V
Ignition switch ON
Shift lever in any position except D or S
0 to 1.5 V
A31-16 (PR) - Body ground Ignition switch ON
Shift lever in P or R
6.0 to 14 V
Ignition switch ON
Shift lever in any position except P or R
0 to 1.5 V
A31-30 (PNB) - Body ground Ignition switch ON
Shift lever in P or N
6.0 to 14 V
Ignition switch ON
Shift lever in any position except P or N
0 to 1.5 V



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
A454551N01
1.292,0.385 1.635,0.615 0.344,0.229 1.333,0.396 1.604,0.594 0.271,0.198 10 true C53

Disconnect the C53 shift lever position sensor connector.


b.

Turn the ignition switch to ON.


c.
A373228C24
1.49,0.198 1.854,0.479 0.365,0.281 1.948,1.74 1.698,1.313 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.563,0.26 1.875,0.458 0.313,0.198 10 false C53 1.927,1.781 2.24,1.979 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Shift Lever Position Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C53-7 (+B) - Body ground Ignition switch ON 6.0 to 14 V


NOTICE:

Turning the ignition switch to ON with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the ignition switch off.


e.

Reconnect the C53 shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT SHIFT LEVER POSITION SENSOR

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)
5.INSPECT SHIFT LEVER POSITION SENSOR

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the C53 shift lever position sensor connector.


b.

Disconnect the A31 hybrid vehicle control ECU connector.


c.
C404098C03
1.49,0.198 1.844,0.469 0.354,0.271 1.573,2.208 1.958,2.469 0.385,0.26 2.104,3.438 2.292,4.073 true 1.76,1.25 2.24,1.719 true 1.615,2.26 1.927,2.458 0.313,0.198 10 false A31 0.198,1.917 0.51,2.115 0.313,0.198 10 false *b 1.552,0.26 1.865,0.458 0.313,0.198 10 false C53 2.156,4.104 2.667,4.417 0.51,0.313 10 false PSFT 2.271,1.698 2.781,2.01 0.51,0.313 10 false +B 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lever Position Sensor)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C53-7 (+B) - A31-18 (PSFT) Ignition switch off Below 1 Ω
C53-7 (+B) or A31-18 (PSFT) - Body ground and other terminals Ignition switch off 10 kΩ or higher



d.

Reconnect the A31 hybrid vehicle control ECU connector.


e.

Reconnect the C53 shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR