Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P0ADD15  Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open Open or short to +B in SMRG circuit:
Primary circuit of SMR (-) is malfunctioning.
(2 trip detection logic)
·

Wire harness or connector

·

HV battery junction block assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0ADD15
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Hybrid Battery Voltage

·

SMRP Status

·

SMRB Status

·

SMRG Status

·

SMRP Control Status

·

SMRB Control Status

·

SMRG Control Status

·

Boosting Converter Shutdown Status

·

Generator Inverter Shutdown Status

·

Motor Inverter Shutdown Status



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

6.

Turn the ignition switch off and wait for 2 minutes or more.

7.

Turn the ignition switch to ON and turn the GTS on.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the HV Battery High-voltage Line Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:

If DTC P0ADD15 is output, the ignition switch cannot be turned to ON (READY).


PROCEDURE

1.READ VALUE USING GTS (SMRG STATUS)
a.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
SMRG Status
50003 397 48
Standard:
Tester Display Condition Specified Condition
SMRG Status Ignition switch ON OFF



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

5.CHECK HARNESS AND CONNECTOR (SMRG VOLTAGE)
2.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

3.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

OK

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (SMRG VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

C407546C78
3.365,0.365 3.75,0.604 0.385,0.24 4.292,1.406 4.365,2.302 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 3.438,0.406 3.75,0.563 0.313,0.156 10 false A32 4.198,2.333 4.708,2.531 0.51,0.198 10 false SMRG
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A32-13 (SMRG) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

NG

CONNECT SECURELY

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the A32 hybrid vehicle control ECU connector.


b.
A456044C02
1.531,0.146 1.99,0.396 0.458,0.25 0.844,1.281 0.667,1.875 true 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a 1.625,0.188 1.969,0.375 0.344,0.188 10 false A32 0.469,1.896 0.948,2.094 0.479,0.198 10 false SMRG
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-13 (SMRG) - Body ground Ignition switch off 25.0 to 59.0 Ω



c.

Reconnect the A32 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
8.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A454533N01
1.313,1.281 1.729,1.552 0.417,0.271 1.333,1.302 1.698,1.521 0.365,0.219 10 true M56

Disconnect the M56 HV battery junction block assembly connector.


d.

Disconnect the A32 hybrid vehicle control ECU connector.


e.

Turn the ignition switch to ON.


f.
C404104C45
2.604,3.333 3.073,3.604 0.469,0.271 1.406,0.167 1.875,0.438 0.469,0.271 2.021,3.406 2.042,3.917 true 0.781,1.344 0.698,1.938 true 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 0.167,2.469 0.479,2.625 0.313,0.156 10 false *b 1.531,0.219 1.865,0.396 0.333,0.177 10 false A32 2.719,3.385 3.052,3.563 0.333,0.177 10 false M56 0.49,1.99 1.104,2.188 0.615,0.198 10 false SMRG 1.927,3.979 2.542,4.177 0.615,0.198 10 false SMRG
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32-13 (SMRG) or M56-4 (SMRG) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the hybrid vehicle control ECU connector and the HV battery junction block assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the ignition switch off.


h.

Reconnect the A32 hybrid vehicle control ECU connector.


i.

Reconnect the M56 HV battery junction block assembly connector.


j.

Install the No. 10 HV battery shield panel.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A454533N01
1.313,1.281 1.729,1.552 0.417,0.271 1.333,1.302 1.698,1.521 0.365,0.219 10 true M56

Disconnect the M56 HV battery junction block assembly connector.


d.

Disconnect the A32 hybrid vehicle control ECU connector.


e.
C404104C45
2.604,3.333 3.073,3.604 0.469,0.271 1.406,0.167 1.875,0.438 0.469,0.271 2.021,3.406 2.042,3.917 true 0.781,1.344 0.698,1.938 true 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 0.167,2.469 0.479,2.625 0.313,0.156 10 false *b 1.531,0.219 1.865,0.396 0.333,0.177 10 false A32 2.719,3.385 3.052,3.563 0.333,0.177 10 false M56 0.49,1.99 1.104,2.188 0.615,0.198 10 false SMRG 1.927,3.979 2.542,4.177 0.615,0.198 10 false SMRG
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A32-13 (SMRG) - M56-4 (SMRG) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A32-13 (SMRG) or M56-4 (SMRG) - Body ground and other terminals Ignition switch off 10 kΩ or higher



f.

Reconnect the A32 hybrid vehicle control ECU connector.


g.

Reconnect the M56 HV battery junction block assembly connector.


h.

Install the No. 10 HV battery shield panel.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

OK

12.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Disconnect the M56 HV battery junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

C384277C36
3.76,1.031 4.115,1.24 0.354,0.208 3.042,1.406 3.313,1.24 true 3.583,1.417 3.417,1.24 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.823,1.063 4.281,1.26 0.458,0.198 10 false M56 3.51,1.448 3.844,1.656 0.333,0.208 10 true GND 2.875,1.406 3.354,1.615 0.479,0.208 10 true SMRG
*a Component without harness connected
(HV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M56-4 (SMRG) - M56-3 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω



e.

Reconnect the M56 HV battery junction block assembly connector.


f.

Install the No. 10 HV battery shield panel.


Result:
Proceed to
OK
NG



OK

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY