Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0419999 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during HV battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of HV battery Battery status info update HV battery status information cannot be updated for 2WD:
(Click here)
for 4WD/AWD:
(Click here)
Replacement of hybrid battery terminal block High voltage fuse accumulated load history reset DTCs are stored

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Navigation System)

·

If the HV battery has been struck or dropped, replace it.

·

When connecting a connector to the HV battery, confirm that the connector is securely connected through the following:

- Push the connector until a click sound is heard.

- Visually check and confirm that the connector is securely connected by pulling on it.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery is stored without insulating the connectors and terminals, electric shock or fire may result.

·

When performing repairs around the HV battery, such as using a tap, do not allow metal shavings to enter the HV battery.

·

Do not touch any high voltage wire harnesses, connectors or parts with bare hands.

·
A455555

Hold the areas shown in the illustration and lift the HV battery.

·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the HV battery.

·
A455556C01
0.854,1.448 0.948,1.74 0.948,1.74 1.146,1.74 true 2.271,1.531 2.365,1.823 2.365,1.823 2.563,1.823 true 2.063,0.219 2.188,0.219 2.188,0.219 2.427,0.333 false 2.594,1.719 2.906,1.917 0.313,0.198 10 false *a 1.177,1.656 1.49,1.854 0.313,0.198 10 false *a 1.896,0.125 2.208,0.323 0.313,0.198 10 false *a
*a Opening


Do not put your hands into the openings of the HV battery.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Do not climb on top of or stand on the HV battery.

·

Do not allow any foreign matter or water to enter the HV battery.

·

If any bolts, nuts or clips are dropped into the HV battery, make sure to remove them.



HINT:

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.


PROCEDURE

Hide 82111 3.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 6.INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.
A451919C01
2.594,1.042 2.813,1.229 0.219,0.188 10 true *a 2.25,0.594 2.469,0.76 0.219,0.167 10 true *b
*a Bolt (A)
*b Bolt (B)


Using a T25 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (A).

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)

NOTICE:
·

Do not touch the connector cover assembly waterproof seal.

·

Do not allow any foreign matter or water to enter the inverter with converter assembly.




b.

Install the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 82111 7.CONNECT ENGINE ROOM MAIN WIRE

Hide G9230 8.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide 65343 9.REMOVE NO. 3 FLOOR BOARD

a.
A455533

Remove the No. 3 floor board.


Hide 65342 10.REMOVE NO. 2 FLOOR BOARD

a.
A455534

Remove the No. 2 floor board.


Hide 65341 11.REMOVE NO. 1 FLOOR BOARD

a.
A455535

Remove the No. 1 floor board.


Hide 12.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 64713F 13.REMOVE FRONT DECK SIDE TRIM COVER LH

Hide 64712F 14.REMOVE FRONT DECK SIDE TRIM COVER RH

Hide 74865D 15.REMOVE CENTER PROTECTOR COVER

a.
A456362N01
1.302,0.677 1.458,0.875 0.156,0.198 10 true A 1.823,0.677 1.979,0.875 0.156,0.198 10 true A 2.344,0.677 2.5,0.875 0.156,0.198 10 true A 2.479,1.26 2.635,1.458 0.156,0.198 10 true B 1.927,1.219 2.083,1.417 0.156,0.198 10 true B 1.385,1.229 1.542,1.427 0.156,0.198 10 true B 0.833,1.26 0.99,1.458 0.156,0.198 10 true B

Remove the 3 clips (A).


b.

Remove the 4 clips (B) and center protector cover.


Hide 73530E 16.REMOVE REAR SEAT SUB FLOOR PANEL ASSEMBLY

a.
A456363

Disconnect the connector.


b.

Remove the 6 bolts and rear seat sub floor panel assembly.


Hide G92QC 17.REMOVE NO. 10 HV BATTERY SHIELD PANEL

CAUTION:

Be sure to wear insulated gloves.


a.
A455538C02
1.427,0.344 1.51,0.219 1.51,0.219 1.656,0.219 false 0.365,1.146 0.521,1.146 0.521,1.146 0.583,1.021 false 1.031,0.302 1.188,0.302 1.188,0.302 1.344,0.5 true 1,0.677 1.229,0.958 1.229,0.958 1.344,0.958 false 0.208,1.063 0.521,1.219 0.313,0.156 10 false *1 1.677,0.135 1.99,0.292 0.313,0.156 10 false *2 1.365,0.865 1.677,1.021 0.313,0.156 10 false *a 1.073,1.021 1.385,1.177 0.313,0.156 10 false *b 0.875,0.198 1.188,0.354 0.313,0.156 10 false *c
*1 Service Plug Grip
*2 Battery Cover Lock Striker
*a Projection
*b Turn
*c Button


Using the service plug grip, remove the battery cover lock striker.

HINT:

Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.



b.

Remove the 6 nuts and No. 10 HV battery shield panel from the HV battery.


Hide 821H1 18.DISCONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A455539C01
2.729,0.823 2.594,0.823 2.594,0.823 2.448,0.667 true 2.74,0.729 2.927,0.927 0.188,0.198 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.

Disengage the clamp.


c.

Disconnect the shield ground from the HV battery.


Hide 82161 19.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A455541

Disengage the 2 clamps.


b.

Disconnect the floor wire connector.


c.

Disconnect the HV battery junction block assembly connector.


d.
A455542

Disconnect the electric vehicle battery plug assembly connector.


e.

Disengage the 3 clamps to disconnect the floor wire.


Hide G92QC 20.INSTALL NO. 10 HV BATTERY SHIELD PANEL

Hide G9510 21.REMOVE HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A455543

Remove the 6 bolts.

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.

·

When removing the HV battery from the vehicle, do not allow it to contact the vehicle.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Insulate the disconnected terminals or connectors with insulating tape.

·

If the HV battery has been struck or dropped, replace it.




b.
A455545

Prepare wooden blocks that will be used to pull out the HV battery.

Wooden block 45 mm (1.7717 in.) x 45 mm (1.7717 in.) x 1000 mm (3.28 ft.)

HINT:

The wooden blocks dimensions are an approximation.



c.
A455544

Tilt the HV battery and place wooden blocks.


d.
A455546

Set the wooden blocks as shown in the illustration.


e.
A455547

Remove the clip and No. 2 HV battery intake duct LH from the HV battery.


f.
A455548

Disengage the clamp.


g.

Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and disconnect the HV battery thermistor from the No. 2 HV battery intake duct RH.

NOTICE:
·

Be careful not to damage the HV battery thermistor.

·

When disconnecting the HV battery thermistor, hold it gently and pull it straight out.




h.

Remove the clip and No. 2 HV battery intake duct RH from the HV battery.


i.
A455549

Pull the HV battery to the rear of the vehicle as shown in the illustration.


j.
A455550

Pull the HV battery to the rear of the vehicle at the positions shown in the illustration.


k.

Using a suitable adaptor such as straps, remove the HV battery while tilting it.

A455551


Hide G92QC 22.REMOVE NO. 10 HV BATTERY SHIELD PANEL

a.

Remove the 6 nuts and No. 10 HV battery shield panel from the HV battery.


Hide 23.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

Hide G920Q 24.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide G92Z2 25.REMOVE HYBRID BATTERY TERMINAL BLOCK

Hide 26.REMOVE NO. 6 HV BATTERY CARRIER BRACKET

Hide 89892A 27.REMOVE BATTERY VOLTAGE SENSOR