Refer to the description for DTC P1AC000.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P1AC000
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0AFC62 | Hybrid/EV Battery Sensor Module Signal Compare Failure | The difference between the voltage output by detection circuit C and the total of the voltage output by detection circuits A and B exceeds the threshold.
HINT: The battery voltage sensor uses 3 voltage detection circuits (A, B and C) to detect the voltage of the battery blocks. (1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B3B14 | Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B4014 | Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B4514 | Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B4A14 | Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B4F14 | Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B5414 | Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B5914 | Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B5E14 | Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B6314 | Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B6814 | Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B6D14 | Hybrid/EV Battery Voltage Sensor "K" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B7214 | Hybrid/EV Battery Voltage Sensor "L" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P0B7714 | Hybrid/EV Battery Voltage Sensor "M" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
| P308A13 | Hybrid/EV Battery Voltage Sensor All Circuit Open | The battery block voltage detection line is open (all blocks) or all battery block voltages become lower than the specified value (possibility of open or loosely connected connector).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning:
Comes on |
Hybrid Battery Block 1 to 12 Voltage values smaller than 2.0 V may not be shown in the Data List because a fail-safe value is substituted.
| DTC No. | Data List |
|---|---|
| P0AFC62 | Hybrid Battery Block 1 to 12 Voltage*1 |
| P0B3B14 | |
| P0B4014 | |
| P0B4514 | |
| P0B4A14 | |
| P0B4F14 | |
| P0B5414 | |
| P0B5914 | |
| P0B5E14 | |
| P0B6314 | |
| P0B6814 | |
| P0B6D14 | |
| P0B7214 | |
| P0B7714 | |
| P308A13 | ·
Hybrid Battery Voltage ·
Hybrid Battery Block 1 to 12 Voltage*1 |
*1: Under normal conditions, the values of Hybrid Battery Block 1, 2, 11 and 12 Voltage will be approximately 16 V and Hybrid Battery Block 3, 4, 5, 6, 7, 8, 9 and 10 Voltage will be approximately 32 V.
If there is a short or open in a battery block voltage detection line, the value of Hybrid Battery Block Voltage for the corresponding battery block will be lower than 8 V.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
With ignition switch ON and wait for 20 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.
If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.
| *a | Dealer |
| *b | Battery Collection Agent |
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Check and record any HV system DTCs and Freeze Frame Data.
| Result | Proceed to |
|---|---|
| P0AFC00, P0AFC96 or P308A12 is not output. | A |
| P0AFC00, P0AFC96 or P308A12 is also output. | B |
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P0AFC00
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs and Freeze Frame Data.
Turn the ignition switch off and wait for 2 minutes or more.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON and wait for 20 seconds or more.
Read output DTCs.
| Result | Proceed to |
|---|---|
| Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are not output. | A |
| Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are output. | B |
Turn the ignition switch off.
A
B