Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P0C7396  Motor Electronics Coolant Pump "A" Component Internal Failure  


DTC SUMMARY

MALFUNCTION DESCRIPTION


This DTC is stored when the inverter water pump assembly is malfunctioning. The cause of this malfunction may be one of the following:

Inverter water pump assembly malfunction
·

Inverter water pump assembly internal malfunction

·

Open or short in wire harness

·

Improperly connected connector


Hybrid cooling system malfunction
·

Foreign matter in inverter water pump assembly

·

Hybrid cooling system coolant is frozen


HINT:

If this DTC is stored, the driving torque may be restricted.



DESCRIPTION

The inverter water pump assembly transmits rotation speed information to the hybrid vehicle control ECU. The hybrid vehicle control ECU monitors the speed and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure The inverter water pump assembly revolution speed is abnormally high or low (or stopped) for 1 minute or more.
(1 trip detection logic)
·

Inverter cooling system

·

Wire harness or connector

·

Inverter water pump assembly

·

Hybrid vehicle control ECU


Comes on Master Warning:
Comes on

HINT:

The inverter water pump assembly operates when the ignition switch is ON (READY).


Related Data List
DTC No. Data List
P0C7396
·

Inverter Water Pump Revolution

·

Inverter Water Pump Duty Ratio

·

Inverter Coolant Water Temperature



Related Active Test
DTC No. Active Test
P0C7396 Activate the Inverter Water Pump

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Turn the ignition switch to ON (READY).

7.

Wait for 2 minutes or more.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

If this vehicle is jump started, etc. and excessive voltage is applied to the auxiliary battery, the inverter water pump assembly may suspend control as a self-protection function and store DTCs.

(When the auxiliary battery voltage returns to normal, the inverter water pump assembly will resume normal operation. In this case it is not necessary to replace the inverter water pump assembly.)


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0C7396 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs including pending DTCs are also output. B


Malfunction Content Relevant DTC
Microcomputer malfunction P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P06881F ECM/PCM Power Relay Sense Circuit Intermittent
Sensor and actuator circuit malfunction P314A31 Motor Electronics Coolant Pump "A" No Signal

HINT:

P0C7396 may be output as a result of the malfunction indicated by the DTCs above.

1.

The chart above is listed in inspection order of priority.

2.

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




b.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)

B

2.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:
·

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.

·

When the inverter water pump assembly signal line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.



a.

According to the display on the GTS, read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Inverter Water Pump Revolution
50003 397 60
OK:
Tester Display Condition Specified Condition
Inverter Water Pump Revolution Ignition switch ON 200 rpm or less


HINT:

When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
3.CLEAR DTC
a.

Read and record the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Trouble Codes
50001 397

b.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

c.

Turn the ignition switch off and wait for 2 minutes or more.


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
4.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the HV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.



HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

According to the display on the GTS, perform the Active Test "Activate the Inverter Water Pump" and, check the value of the Data List item "Inverter Water Pump Revolution".

Powertrain > Hybrid Control > Active Test
Active Test Display
Activate the Inverter Water Pump
Data List Display
Inverter Water Pump Revolution
50004 397 1 60
OK:
Tester Display Condition Specified Condition
Inverter Water Pump Revolution Ignition switch ON
During Active Test
3176 to 8617 rpm


HINT:
·

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).

·

When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.




b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

5.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

NG

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
5.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>Cooling System

Result:
Result Proceed to
Ambient Temperature value is above freezing temperature of the HV coolant. A
Ambient Temperature value is below freezing temperature of the HV coolant. B



A

12.REPLACE INVERTER WATER PUMP ASSEMBLY

B

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Disconnect the A56 inverter water pump assembly connector.


c.
A368425C21
1.542,2.688 1.896,2.958 0.354,0.271 1.427,0.333 1.823,0.594 0.396,0.26 2.385,2.323 2.542,1.719 true 1.708,4.094 1.823,3.552 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 0.188,2.729 0.5,2.927 0.313,0.198 10 false *b 1.552,4.135 2.104,4.427 0.552,0.292 10 false SWP 2.26,2.365 2.635,2.563 0.375,0.198 10 false IWP 1.51,0.375 2.063,0.667 0.552,0.292 10 false A31 1.604,2.75 2.156,3.042 0.552,0.292 10 false A56
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A31-34 (IWP) - A56-3 (SWP) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A31-34 (IWP) or A56-3 (SWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.



d.

Reconnect the A56 inverter water pump assembly connector.


e.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.
A449764C01
2,1.698 2.604,2.458 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.635,2.458 2.948,2.656 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from No. 1 engine room relay block and No. 1 junction block assembly.


b.

According to the display on the GTS, read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Inverter Water Pump Revolution
50003 397 60
OK:
Tester Display Condition Specified Condition
Inverter Water Pump Revolution Ignition switch ON 200 rpm or less



c.

Turn the ignition switch off.


d.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.
A449788C01
0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.333,1.24 0.646,1.438 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay Holder


Remove the INV W/PMP relay from No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the A31 hybrid vehicle control ECU connector.


c.

Connect terminals 3 and 5 of the INV W/PMP relay holder.

HINT:

Make a short circuit between terminals 3 and 5 to supply +B voltage to the inverter water pump.



d.

Measure the voltage according to the value(s) in the table below.

A368426C30
5.26,0.167 5.656,0.458 0.396,0.292 2.76,2.698 3.156,2.948 0.396,0.25 2.479,3.448 2.313,3.042 true 5.906,2.104 5.99,1.177 true 0.375,2.135 0.688,2.333 0.313,0.198 10 false *b 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 5.323,0.229 5.698,0.427 0.375,0.198 10 false H67 2.823,2.74 3.135,2.938 0.313,0.198 10 false A31 2.406,3.469 2.865,3.667 0.458,0.198 10 false IWP 5.823,2.125 6.281,2.323 0.458,0.198 10 false E1
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Standard Voltage:
Tester Connection Condition Specified Condition
A31-34 (IWP) - H67-3 (E1) INV W/PMP relay holder terminals 3 and 5 connected
Ignition switch off
11 to 14 V


NOTICE:

Make sure to check for and clear DTCs after performing this inspection.



e.

Reconnect the A31 hybrid vehicle control ECU connector.


f.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

11.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

NG

12.REPLACE INVERTER WATER PUMP ASSEMBLY
11.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.


b.

Turn the ignition switch to ON.


c.

Check the waveform while turning the ignition switch to ON.

C407546C88
5.271,0.344 5.615,0.594 0.344,0.25 1.552,0.281 1.896,0.531 0.344,0.25 1.125,1.49 1.375,2.271 true 6.01,1.302 5.917,2.302 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 5.333,0.385 5.792,0.583 0.458,0.198 10 false H67 1.292,2.313 1.781,2.563 0.49,0.25 10 false IWP 5.833,2.354 6.104,2.531 0.271,0.177 10 false E1 1.604,0.333 2.063,0.531 0.458,0.198 10 false A31
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Content
Terminal A31-34 (IWP) - H67-3 (E1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Ignition switch ON

OK:

Waveform duty ratio is between 3% and 9%.



d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

12.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

12.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

13.ADD HV COOLANT AND PERFORM AIR BLEEDING
13.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

END