Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P1C2D62  Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU detects a VB sensor or VL sensor malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage (VB or VL) sensor internal circuit malfunction
·

Voltage sensor malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

HV battery malfunction

·

HV battery junction block assembly malfunction

·

Inverter with converter assembly malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction



Inspection Overview


Inspection Content Reason (Narrow Down in Order Using Inspection Procedures Below) Inspection Step
Check for DTCs (HV) Output DTCs 1
Check for DTCs (check voltage sensor malfunction locations)
Check for DTCs (drive test)
Ignition switch ON (READY) (vehicle stopped or being driven) and then check whether DTCs are output again. 3, 4
Read value using GTS Data List value 5
Check freeze frame data (HV) Freeze Frame Data 6, 7
Read value using GTS Accelerator and brake pedal simultaneously depressed Data List value 8


DESCRIPTION

For a description of the boost converter.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>P0CA300

The MG ECU uses a voltage sensor (VL) that is built into the boost converter to detect the high voltage before it is boosted. The ECU also uses the battery voltage sensor to detect HV battery voltage (VB).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C2D62 Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate:
Difference between "VL-Voltage before Boosting" and "Hybrid Battery Voltage" is large when the boosting request is given.
(1 trip detection logic)
·

Inverter with converter assembly

·

Battery voltage sensor


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P1C2D62
·

Hybrid Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Boost Ratio



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Turn the ignition switch to ON (READY).

7.

With the shift lever in D, depress both the accelerator pedal and brake pedal at the same time to raise the "Hybrid Battery SOC" to a sufficient level.

8.

Move the shift lever to P, check that the engine is stopped and move the shift lever to N.

9.

Set the A/C for maximum cooling.

10.

Leave the vehicle for a few minutes.

HINT:

When the accelerator pedal is not depressed with the ignition switch ON (READY) and shift lever in P, if "VL-Voltage before Boosting" and the "Hybrid Battery Voltage" is approximately the same after repair, the condition is judged as normal.


11.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

12.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
One of the following applies:
·

Only P1C2D62 is output.

·

One or more DTCs other than P0E311C, P0CA300, P0B231C, and DTCs in the table below are also output.


A
P1C2D62 and P0E311C or P0CA300 are output at the same time. B
P1C2D62 and P0B231C are output at the same time. C
DTCs of Hybrid Control System in the tables below are output. D
DTCs of Motor Generator Control System in the tables below are output. E


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid Control System P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P0AFC00 Hybrid/EV Battery Sensor Module
P0AFC96 Hybrid/EV Battery Sensor Module Component Internal Failure
Motor Generator Control System P0A1A47 Generator Control Module Watchdog / Safety MC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P0A1B1F Generator Control Module Circuit Intermittent
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Power source circuit malfunction Hybrid Control System P0AFC16 Hybrid/EV Battery Sensor Module Circuit Voltage Below Threshold
Motor Generator Control System P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Communication system malfunction Hybrid Control System P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U029A87 Lost Communication with Hybrid/EV Battery Sensor Module Missing Message
Sensor and actuator circuit malfunction Hybrid Control System P0B3B14 Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open
P0B4014 Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open
P0B4514 Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open
P0B4A14 Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open
P0B4F14 Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open
P0B5414 Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open
P0B5914 Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open
P0B5E14 Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open
P0B6314 Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open
P0B6814 Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open
P0B6D14 Hybrid/EV Battery Voltage Sensor "K" Circuit Short to Ground or Open
P0B7214 Hybrid/EV Battery Voltage Sensor "L" Circuit Short to Ground or Open
P0B7714 Hybrid/EV Battery Voltage Sensor "M" Circuit Short to Ground or Open
P308A13 Hybrid/EV Battery Voltage Sensor All Circuit Open
P0AFC62 Hybrid/EV Battery Sensor Module Signal Compare Failure
P308A12 Hybrid/EV Battery Voltage Sensor All Circuit Short to Auxiliary Battery
System malfunction Motor Generator Control System P0E3116 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold

HINT:
·

P1C2D62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





b.

Turn the ignition switch off.



A

2.CLEAR DTC

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

D

E

2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (CHECK FAILURE PART)
3.CHECK DTC OUTPUT (CHECK FAILURE PART)
a.

Apply the parking brake and secure the wheels using chocks.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.


HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch assembly has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch assembly is pulled to the lock side one more time.



b.

Connect the GTS to the DLC3. *1


c.

Turn the ignition switch to ON (READY). *2


d.

Read the Data List. *3

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery SOC
Hybrid Battery Current
50003 397 320,228

e.

If the value of "Hybrid Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more. *4


f.

Move the shift lever to P. *5


g.

Set the air conditioning to MAX COOL and turn the headlights on. *6


h.

Confirm that "Hybrid Battery Current" is more than 3 A. *7


i.

With the engine stopped and the conditions of steps *5, *6 and *7 satisfied, leave the vehicle for 15 seconds. *8


j.

Enter the following menus: Powertrain / Hybrid Control, Motor Generator / Trouble codes. *9


k.

Check for DTCs. *10

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
NOTICE:

If the low HV battery information comes on, move the shift lever to P and start the engine to charge the HV battery. After the engine stops, perform steps *1 through *10 again.


Result:
Result Proceed to
No DTCs are output, or DTCs except the following are output. A
P0E311C or P0CA300 are output. B
P0B231C or P1C8349 are output. C
P300000 is output. D



l.

Turn the ignition switch off.



A

4.CHECK DTC OUTPUT (ROAD TEST)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

D

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS *1 THROUGH *10)

4.CHECK DTC OUTPUT (ROAD TEST)
a.

Turn the ignition switch to ON (READY). *11


b.

Perform a road test that repeats full acceleration to 60 km/h (37 mph) and then braking to a complete stop three times. *12

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

This road test is performed to drive the car under high load and cause a change in the HV battery voltage.



c.

Connect the GTS to the DLC3. *13


d.

Enter the following menus: Powertrain / Hybrid Control, Motor Generator / Trouble Codes. *14


e.

Check for DTCs. *15

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
No DTCs are output, or DTCs except the following are output. A
P0E311C or P0CA300 are output. B
P0B231C or P1C8349 are output. C
P300000 is output. D



f.

Turn the ignition switch off.



A

5.READ VALUE USING GTS (DATA LIST)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

D

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS *11 THROUGH *15)

5.READ VALUE USING GTS (DATA LIST)
a.

Apply the parking brake and secure the wheels using chocks.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.


HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch assembly has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch assembly is pulled to the lock side one more time.



b.

Turn the ignition switch to ON (READY).


c.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
VL-Voltage before Boosting
VH-Voltage after Boosting
Hybrid Battery SOC
Hybrid Battery Voltage
50003 397 150,151,320,227

d.

If the value of "Hybrid Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more.


e.

Release the accelerator pedal, move the shift lever to P and wait for the engine to stop. Read the Data List when the engine stops.

HINT:

If the engine starts, wait until it stops before continuing.


Result:
Result Proceed to
Both of the following are not satisfied. A
Both of the following are satisfied:
·

Difference between "Hybrid Battery Voltage" and "VH-Voltage after Boosting" is less than 5 V.

·

Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 30 V.


B
Both of the following are satisfied:
·

Difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is less than 5 V.

·

Difference between "Hybrid Battery Voltage" and "VH-Voltage after Boosting" is more than 15 V.


C



f.

Turn the ignition switch off.



A

6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Read the Freeze Frame Data of DTC P1C2D62.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Both of the following are satisfied or both of the following are not satisfied. A
"VL-Voltage before Boosting" is less than 240 V or more than 400 V. B
"Hybrid Battery Voltage" is less than 240 V or more than 400 V. C



b.

Turn the ignition switch off.



A

7.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

7.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Read the Freeze Frame Data of DTC P1C2D62.

Powertrain > Hybrid Control > Trouble Codes
50001 397
HINT:

In the freeze frame data, read the item "Hybrid Battery Voltage" and all of the "Hybrid Battery Block 1 to 12 Voltage".


Result:
Result Proceed to
Freeze frame data is not stored. A
Both of the following are satisfied:
·

Sum of all "Hybrid Battery Block 1 to 12 Voltage" is more than ("Hybrid Battery Voltage" - 55 V)

·

Sum of all "Hybrid Battery Block 1 to 12 Voltage" is less than ("Hybrid Battery Voltage" + 35 V)


B
Neither A nor B is satisfied. C



b.

Turn the ignition switch off.



A

8.READ VALUE USING GTS (DATA LIST)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

8.READ VALUE USING GTS (DATA LIST)
a.

Apply the parking brake and secure the wheels using chocks.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.


HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch assembly has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch assembly is pulled to the lock side one more time.



b.

Turn the ignition switch to ON (READY).


c.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery SOC
Hybrid Battery Voltage
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
Hybrid Battery Block 9 Voltage
Hybrid Battery Block 10 Voltage
Hybrid Battery Block 11 Voltage
Hybrid Battery Block 12 Voltage
50003 397 320,227,161,162,163,164,165,166,167,168,169,170,307,308

d.

If the value of "Hybrid Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more.


e.

Release the accelerator pedal, move the shift lever to P and wait for the engine to stop. Read the Data List when the engine stops.

HINT:

If the engine starts, wait until it stops before continuing.


Result:
Result Proceed to
Both of the following are satisfied:
·

Sum of all "Hybrid Battery Block 1 to 12 Voltage" is more than ("Hybrid Battery Voltage" - 55 V)

·

Sum of all "Hybrid Battery Block 1 to 12 Voltage" is less than ("Hybrid Battery Voltage" + 35 V)


A
The preceding condition is not satisfied. B



f.

Turn the ignition switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B