MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU calculates the accelerator pedal opening angle based on the output voltage of the main sensor (VPA) and sub sensor (VPA2) of the accelerator pedal sensor assembly. If the output voltage of either the main sensor (VPA) or sub sensor (VPA2) deviates, a malfunction will be detected.
The cause of this malfunction may be one of the following:
Accelerator pedal sensor assembly malfunction
Wire harness or connector malfunction
Hybrid vehicle control ECU malfunction
The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and detects how much the pedal is depressed. This is a non-contact sensor with Hall elements. There are 2 outputs from the sensor. One is used to detect the accelerator pedal position and the other is used as a confirmation to allow the detection of a malfunction in the sensor itself. Voltage is output from the accelerator pedal position sensor to terminals VPA and VPA2 of the hybrid vehicle control ECU. This voltage varies from 0 to 5 V in accordance with the accelerator pedal position. Terminal VPA2 is primarily used to detect a malfunction in the sensor itself. The hybrid vehicle control ECU determines the current accelerator pedal position and controls the hybrid control system based on signals received by terminals VPA and VPA2.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P212012 | Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery | Short to +B in the main sensor circuit:
The main sensor voltage is 4.8 V or more for 2 seconds. (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P212014 | Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open | Open or short to ground in the main sensor circuit:
The main sensor voltage is 0.4 V or less for 0.5 seconds. (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P21201C | Throttle/Pedal Position Sensor/Switch "D" Voltage Out of Range | Internal malfunction in the main sensor:
Main sensor output changes rapidly (detected when there are no circuit malfunctions such as an open or short). (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P21201F | Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent | Main sensor circuit wiring malfunction or level is not stable:
Main sensor voltage is 0.4 V or less or 4.8 V or more for a certain period of time. (Both of the following conditions are met: The main sensor voltage is 0.4 V or less for a certain period of time and 4.8 V or more for a certain period of time.) (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P212512 | Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery | Short to +B in the sub sensor circuit:
Main sensor is normal and sub sensor voltage is 4.8 V or more for 2 seconds. (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P212514 | Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open | Open or short to ground in the sub sensor circuit:
The sub sensor voltage is 1.2 V or less for 0.5 seconds. (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P21251C | Throttle/Pedal Position Sensor/Switch "E" Voltage Out of Range | Internal malfunction of the sub sensor:
Sub sensor output changes rapidly (detected when there are no circuit malfunctions such as an open or short). (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P21251F | Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent | Sub sensor circuit wiring malfunction or level is not stable:
When the main sensor circuit is normal, the sub sensor voltage is 1.2 V or less or 4.8 V or more for a certain period of time. (Both of the following conditions are met: Sub sensor voltage is 1.2 V or less for a certain period of time, and the main sensor is normal and sub sensor voltage is 4.8 V or more for a certain period of time.) (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P213800 | Throttle/Pedal Position Sensor/Switch "D"/" E" Voltage Correlation | Difference between the main sensor value and sub sensor value is large.
(1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| P21382B | Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled | Main or sub sensor circuit wiring malfunction:
The difference in voltage between the main sensor and sub sensor is 0.02 V or less, or a low output malfunction continues in both the main and sub sensors for a certain period of time. (1 trip detection logic) |
·
Wire harness or connector ·
Accelerator pedal sensor assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P212012 | ·
Accelerator Position Sensor No. 1 Voltage % ·
Accelerator Position Sensor No. 2 Voltage % |
| P212014 | |
| P21201C | |
| P21201F | |
| P212512 | |
| P212514 | |
| P21251C | |
| P21251F | |
| P213800 | |
| P21382B |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Wait for approximately 10 seconds with the ignition switch ON (READY) and shift lever in P, then fully depress and release the accelerator pedal several times.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Read the Data List.
| Tester Display |
|---|
| Accelerator Position Sensor No.1 Voltage % |
| Accelerator Position Sensor No.2 Voltage % |
| Tester Display | Accelerator Pedal Condition | Specified Condition |
|---|---|---|
| Accelerator Position Sensor No. 1 Voltage % | Not depressed | 10 to 22% |
| Fully depressed | 52 to 90% | |
| Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) | Value changes progressively | |
| Accelerator Position Sensor No. 2 Voltage % | Not depressed | 24 to 40% |
| Fully depressed | 68 to 99% | |
| Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) | Value changes progressively |
Turn the ignition switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connections and contact pressure of the relevant terminals for the accelerator pedal sensor assembly connector.
The connectors are connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A26 accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A26-4 (VCPA) - A26-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| A26-1 (VCP2) - A26-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
Turn the ignition switch off.
Reconnect the A26 accelerator pedal sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A26 accelerator pedal sensor assembly connector.
| *a | Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A26-6 (VPA) - A26-5 (EPA) | Ignition switch off | 28.00 to 41.61 kΩ |
| A26-3 (VPA2) - A26-2 (EPA2) | Ignition switch off | 28.00 to 41.61 kΩ |
Reconnect the A26 accelerator pedal sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A31 hybrid vehicle control ECU connector.
Disconnect the A26 accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-24 (VCPA) - Body ground | Ignition switch ON | Below 1 V |
| A31-37 (EPA) - Body ground | Ignition switch ON | Below 1 V |
| A31-26 (VCP2) - Body ground | Ignition switch ON | Below 1 V |
| A31-25 (EPA2) - Body ground | Ignition switch ON | Below 1 V |
Turning the ignition switch to ON with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-24 (VCPA) - A26-4 (VCPA) | Ignition switch off | Below 1 Ω |
| A31-37 (EPA) - A26-5 (EPA) | Ignition switch off | Below 1 Ω |
| A31-26 (VCP2) - A26-1 (VCP2) | Ignition switch off | Below 1 Ω |
| A31-25 (EPA2) - A26-2 (EPA2) | Ignition switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-24 (VCPA) or A26-4 (VCPA) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| A31-37 (EPA) or A26-5 (EPA) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| A31-26 (VCP2) or A26-1 (VCP2) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| A31-25 (EPA2) or A26-2 (EPA2) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
Reconnect the A26 accelerator pedal sensor assembly connector.
Reconnect the A31 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A31 hybrid vehicle control ECU connector.
Disconnect the A26 accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-36 (VPA) - Body ground | Ignition switch ON | Below 1 V |
| A31-38 (VPA2) - Body ground | Ignition switch ON | Below 1 V |
| A31-37 (EPA) - Body ground | Ignition switch ON | Below 1 V |
| A31-25 (EPA2) - Body ground | Ignition switch ON | Below 1 V |
Turning the ignition switch to ON with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-36 (VPA) - A26-6 (VPA) | Ignition switch off | Below 1 Ω |
| A31-37 (EPA) - A26-5 (EPA) | Ignition switch off | Below 1 Ω |
| A31-38 (VPA2) - A26-3 (VPA2) | Ignition switch off | Below 1 Ω |
| A31-25 (EPA2) - A26-2 (EPA2) | Ignition switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-36 (VPA) or A26-6 (VPA) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| A31-37 (EPA) or A26-5 (EPA) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| A31-38 (VPA2) or A26-3 (VPA2) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| A31-25 (EPA2) or A26-2 (EPA2) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
Reconnect the A26 accelerator pedal sensor assembly connector.
Reconnect the A31 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG