Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P260031  Motor/Generator Coolant Pump "A" Control Circuit No Signal  


DESCRIPTION

The hybrid vehicle control ECU detects the generator (MG1) and motor (MG2) temperature based on signals from the generator and motor temperature sensors and activates the OIL PMP relay and oil pump driver (oil pump with motor assembly).

The hybrid vehicle control ECU monitors NOPM signals from the oil pump driver (oil pump with motor assembly) and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P260031 Motor/Generator Coolant Pump "A" Control Circuit No Signal When the OIL PMP relay is on, the NOPM pulse signal is not output.
(2 trip detection logic)
·

Oil pump with motor assembly

·

Hybrid vehicle control ECU

·

Wire harness or connector

·

OIL PMP relay

·

OIL PMP fuse


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P260031
·

Target Motor/Generator Cooling Oil Pump Motor Duty

·

Motor/Generator Cooling Oil Pump Motor Revolution

·

Motor/Generator Cooling Oil Pump Motor Power Relay Request



HINT:

The oil pump with motor assembly cannot be activated only with the OIL PMP relay on. It is activated after receiving the command signals (OPM1) from the hybrid vehicle control ECU.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Motor/Generator Cooling Oil Pump.

6.

According to the display on the GTS, perform the Active Test and set the duty to 90%.

HINT:

The Active Test cannot be performed if the duty ratio is set to 50% or lower or 95% or higher, or if the ambient temperature is 0°C (30°F) or lower.


7.

According to the display on the GTS, read the Data List and check that the value of "Motor/Generator Cooling Oil Pump Motor Revolution" is between 160 rpm and 7600 rpm.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A456738E01
5.302,4.073 7.01,4.573 1.708,0.5 10 false Hybrid Vehicle Control ECU 0.219,1.083 0.802,1.813 0.583,0.729 10 false from Auxiliary Battery 5.063,1.292 5.396,1.531 0.333,0.24 10 false A31 5.073,2.156 5.406,2.396 0.333,0.24 10 false A31 5.083,3.656 5.417,3.896 0.333,0.24 10 false H67 3.073,2.615 3.406,2.854 0.333,0.24 10 false C38 5.438,3.656 5.771,3.896 0.333,0.24 10 false E1 5.427,3.031 5.865,3.323 0.438,0.292 10 false OPM2 5.146,3.448 5.406,3.646 0.26,0.198 10 false 3 5.104,2.906 5.365,3.104 0.26,0.198 10 false 12 5.115,1.948 5.375,2.146 0.26,0.198 10 false 21 5.104,1.083 5.365,1.281 0.26,0.198 10 false 22 5.427,2.042 5.865,2.333 0.438,0.292 10 false OPM1 5.427,1.188 5.948,1.5 0.521,0.313 10 false NOPM 4.177,2.042 4.615,2.333 0.438,0.292 10 false OPM1 4.146,1.177 4.667,1.49 0.521,0.313 10 false NOPM 4.646,1.177 4.906,1.375 0.26,0.198 10 false 2 4.646,2.042 4.906,2.24 0.26,0.198 10 false 3 3.302,2.042 3.563,2.24 0.26,0.198 10 false 1 3.292,1.188 3.552,1.385 0.26,0.198 10 false 4 3.5,1.281 3.76,1.479 0.26,0.198 10 false L 3.479,2.146 3.938,2.396 0.458,0.25 10 false OPG 2.552,1.573 2.813,1.771 0.26,0.198 10 false 1 1.99,1.573 2.25,1.771 0.26,0.198 10 false 2 1.219,1.188 1.479,1.385 0.26,0.198 10 false 1 1.667,1.177 1.927,1.375 0.26,0.198 10 false 2 1.979,1.177 2.24,1.375 0.26,0.198 10 false 3 2.563,1.177 2.823,1.375 0.26,0.198 10 false 5 1.208,1.448 1.813,1.781 0.604,0.333 10 false OIL PMP 2.042,1.958 2.646,2.292 0.604,0.333 10 false OIL PMP 3.073,2.76 5.083,3.323 2.01,0.563 10 false Oil Pump with Motor Assembly 5.063,3.125 5.396,3.365 0.333,0.24 10 false A31

PROCEDURE

1.READ VALUE USING GTS (MOTOR/GENERATOR COOLING OIL PUMP MOTOR REVOLUTION)
a.

Set the Duty ratio to 90%.

HINT:

The active test is not performed when the Duty ratio is 50% or lower or 95% or higher, or the ambient temperature is 0°C (30°F) or lower.


Powertrain > Hybrid Control > Active Test
Active Test Display
Control the Motor/Generator Cooling Oil Pump
Data List Display
Motor/Generator Cooling Oil Pump Motor Revolution
50004 397 42002 393

b.

According to the display on the GTS, perform the Active Test "Control the Motor/Generator Cooling Oil Pump" and, check the value of the Data List item "Motor/Generator Cooling Oil Pump Motor Revolution".

OK:
Tester Display Condition Specified Condition
Motor/Generator Cooling Oil Pump Motor Revolution Ignition switch ON
During Active Test
160 to 7600 rpm



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK FOR INTERMITTENT PROBLEMS

NG

3.CHECK CONNECTOR CONNECTION CONDITION (OIL PUMP WITH MOTOR ASSEMBLY CONNECTOR)
2.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

3.CHECK CONNECTOR CONNECTION CONDITION (OIL PUMP WITH MOTOR ASSEMBLY CONNECTOR)
a.
A449768N01
2.146,0.594 2.51,0.854 0.365,0.26 2.177,0.625 2.479,0.833 0.302,0.208 10 true C38

Check the connector connections and contact pressure of the relevant terminals for the C38 oil pump with motor assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG



OK

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the C38 oil pump with motor assembly connector.


b.

Set the Duty ratio to 90%.

HINT:

The active test is not performed when the Duty ratio is 50% or lower or 95% or higher, or the ambient temperature is 0°C (30°F) or lower.


Powertrain > Hybrid Control > Active Test
Tester Display
Control the Motor/Generator Cooling Oil Pump
50004 397 42002

c.
A449798C03
0.292,1.115 0.667,1.385 0.375,0.271 2.354,1.885 2.198,1.26 true 0.219,0.104 0.51,0.344 0.292,0.24 10 false *a 0.354,1.177 0.667,1.458 0.313,0.281 10 false C38 2.365,1.917 2.708,2.156 0.344,0.24 10 false L
*a Front view of wire harness connector
(to Oil Pump with Motor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C38-4 (L) - Body ground Ignition switch ON
During Active Test
11 to 14 V


NOTICE:

Turning the ignition switch to ON with the oil pump with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the ignition switch off.


e.

Reconnect the C38 oil pump with motor assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - BODY GROUND)

NG

9.CHECK FUSE (OIL PMP)
6.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - BODY GROUND)
a.

Disconnect the C38 oil pump with motor assembly connector.


b.
A449798C01
0.292,1.115 0.667,1.385 0.375,0.271 0.979,1.844 1.219,1.25 true 0.219,0.104 0.51,0.344 0.292,0.24 10 false *a 0.354,1.177 0.667,1.458 0.313,0.281 10 false C38 0.823,1.875 1.167,2.115 0.344,0.24 10 false OPG
*a Front view of wire harness connector
(to Oil Pump with Motor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C38-1 (OPG) - Body ground Ignition switch off Below 1 Ω



c.

Reconnect the C38 oil pump with motor assembly connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Disconnect the C38 oil pump with motor assembly connector.


c.
A456737C01
1.417,0.104 1.854,0.385 0.438,0.281 1.521,2.552 1.958,2.833 0.438,0.281 2.688,2.115 2.583,1.229 true 1.292,4.229 1.583,3.479 true 0.26,0.177 0.573,0.333 0.313,0.156 10 false *a 0.313,2.719 0.625,2.875 0.313,0.156 10 false *b 1.51,0.167 1.969,0.365 0.458,0.198 10 false A31 1.615,2.625 2.073,2.823 0.458,0.198 10 false C38 2.51,2.156 3.125,2.354 0.615,0.198 10 false NOPM 1.073,4.26 1.688,4.458 0.615,0.198 10 false NOPM
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Oil Pump with Motor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A31-22 (NOPM) - C38-2 (NOPM) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A31-22 (NOPM) or C38-2 (NOPM) - Body ground and other terminals Ignition switch off 10 kΩ or higher



d.

Reconnect the C38 oil pump with motor assembly connector.


e.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Disconnect the C38 oil pump with motor assembly connector.


c.
A456737C02
1.417,0.104 1.854,0.385 0.438,0.281 1.521,2.552 1.958,2.833 0.438,0.281 2.531,2.125 2.427,1.24 true 2.146,4.198 1.885,3.479 true 0.26,0.177 0.573,0.333 0.313,0.156 10 false *a 0.313,2.719 0.625,2.875 0.313,0.156 10 false *b 1.51,0.167 1.969,0.365 0.458,0.198 10 false A31 1.615,2.625 2.073,2.823 0.458,0.198 10 false C38 2.365,2.156 2.979,2.354 0.615,0.198 10 false OPM1 1.99,4.24 2.604,4.438 0.615,0.198 10 false OPM1
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Oil Pump with Motor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A31-21 (OPM1) - C38-3 (OPM1) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A31-21 (OPM1) or C38-3 (OPM1) - Body ground and other terminals Ignition switch off 10 kΩ or higher



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A31-21 (OPM1) or C38-3 (OPM1) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the hybrid vehicle control ECU and oil pump with motor assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the ignition switch off.


g.

Reconnect the C38 oil pump with motor assembly connector.


h.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

REPLACE OIL PUMP WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FUSE (OIL PMP)
a.

Remove the OIL PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
A449789C01
2.063,1.615 2.719,2.344 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *1 2.729,2.354 3.042,2.51 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 OIL PMP Fuse


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
OIL PMP fuse Always Below 1 Ω



c.

Install the OIL PMP fuse.


Result:
Proceed to
OK
NG



OK

10.INSPECT RELAY (OIL PMP)

NG

REPLACE FUSE (OIL PMP)

10.INSPECT RELAY (OIL PMP)
a.
A449790C01
0.813,2.063 1.396,1.188 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *1 0.708,2.073 1.021,2.271 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 OIL PMP Relay


Remove the OIL PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
E222294C55
1.073,0.958 1.198,0.49 1.198,0.49 1.396,0.49 true 1.125,1.344 1.167,1.75 1.167,1.75 1.406,1.75 true 0.802,1.01 0.75,0.49 0.75,0.49 0.458,0.49 true 0.563,1.281 0.49,1.771 0.49,1.771 0.313,1.771 true 1.458,0.406 1.604,0.656 0.146,0.25 10 false 1 1.458,1.667 1.635,1.896 0.177,0.229 10 false 2 0.344,0.406 0.521,0.604 0.177,0.198 10 false 5 0.188,1.698 0.344,1.885 0.156,0.188 10 false 3 0.115,0.094 0.302,0.333 0.188,0.24 10 false *1
*1 OIL PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the OIL PMP relay.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPLACE RELAY (OIL PMP)