Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P26009E  Motor/Generator Coolant Pump "A" Control Circuit Stuck On  


DESCRIPTION

Refer to the description for DTC P260031.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P260031

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P26009E Motor/Generator Coolant Pump "A" Control Circuit Stuck On When the OIL PMP relay is off, the NOPM input pulse signal is received.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

Wire harness or connector

·

OIL PMP relay


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P26009E
·

Target Motor/Generator Cooling Oil Pump Motor Duty

·

Motor/Generator Cooling Oil Pump Motor Revolution

·

Motor/Generator Cooling Oil Pump Motor Power Relay Request



HINT:

The oil pump with motor assembly cannot be activated only with the OIL PMP relay on. It is activated after receiving the command signals (OPM1) from the hybrid vehicle control ECU.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Motor/Generator Cooling Oil Pump.

6.

According to the display on the GTS, perform the Active Test and set the duty to 90%.

HINT:

The Active Test cannot be performed if the duty ratio is set to 50% or lower or 95% or higher, or if the ambient temperature is 0°C (30°F) or lower.


7.

According to the display on the GTS, read the Data List and check that the value of "Motor/Generator Cooling Oil Pump Motor Revolution" is between 160 rpm and 7600 rpm.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

PROCEDURE

1.INSPECT RELAY (OIL PMP)

OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PMP RELAY)

NG

REPLACE RELAY (OIL PMP)

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PMP RELAY)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Remove the OIL PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

A456736C01
0.354,1.271 0.771,1.531 0.417,0.26 2.74,2.24 2.573,1.365 true 0.438,1.323 0.896,1.521 0.458,0.198 10 false A31 2.573,2.281 3.188,2.479 0.615,0.198 10 false OPM2 4.563,0.115 4.875,0.271 0.313,0.156 10 false *1 4.063,0.615 4.375,0.771 0.313,0.156 10 false *2 0.646,0.458 0.958,0.615 0.313,0.156 10 false *a
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly *2 OIL PMP Relay Holder
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A31-12 (OPM2) or 1 (OIL PMP relay holder) - Body ground and other terminals Ignition switch off Below 1 V


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A31-12 (OPM2) or 1 (OIL PMP relay holder) - Body ground and other terminals Ignition switch ON Below 1 V


NOTICE:
·

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.

·

Turning the ignition switch to ON with the hybrid vehicle control ECU connector and OIL PMP relay disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.




f.

Turn the ignition switch off.


g.

Install the OIL PMP relay.


h.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (OIL PMP RELAY - OIL PUMP WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (OIL PMP RELAY - OIL PUMP WITH MOTOR ASSEMBLY)
a.

Disconnect the C38 oil pump with motor assembly connector.


b.
A449798C02
0.292,1.073 0.667,1.344 0.375,0.271 2.406,1.865 2.208,1.26 true 0.219,0.104 0.51,0.344 0.292,0.24 10 false *a 0.354,1.135 0.667,1.417 0.313,0.281 10 false C38 2.417,1.885 2.76,2.125 0.344,0.24 10 false L
*a Front view of wire harness connector
(to Oil Pump with Motor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C38-4 (L) - Body ground Ignition switch off Below 1 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C38-4 (L) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the oil pump with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the ignition switch off.


f.

Reconnect the C38 oil pump with motor assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR