Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  U029A87  Lost Communication with Hybrid/EV Battery Sensor Module Missing Message  


DESCRIPTION

The battery voltage sensor detects the HV battery conditions (voltage, current and temperature) and the battery cooling fan frequency, and sends the detected signals to the hybrid vehicle control ECU via CAN communication. (The hybrid vehicle control ECU does not send signals to the battery voltage sensor.)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
U029A87 Lost Communication with Hybrid/EV Battery Sensor Module Missing Message CAN communication error between the hybrid vehicle control ECU and battery voltage sensor: The hybrid vehicle control ECU cannot receive signals from the battery voltage sensor correctly.
(1 trip detection logic)
·

Battery voltage sensor

·

Wire harness or connector


Comes on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C76
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check and record any Hybrid System DTCs and Freeze Frame Data. Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only U029A87 is output. A
DTCs other than U029A87 are also output. B



b.

Turn the ignition switch off.



A

2.CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE)

B

2.CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FUSE BOX>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


e.
A449753C07
2.115,0.229 2.552,0.458 0.438,0.229 2.073,1.719 2.479,0.958 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.219,0.271 2.615,0.583 0.396,0.313 10 false y1 1.823,1.813 2.156,2.073 0.333,0.26 10 false IGCT 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
y1-1 (IGCT) - y1-7 (GND) Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction in the battery voltage sensor power source circuit, inspect the following even if the measured voltage is as specified:

·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)




f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery shield sub-assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY VOLTAGE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY VOLTAGE SENSOR POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY VOLTAGE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A32 hybrid vehicle control ECU connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the hybrid vehicle control ECU and battery voltage sensor is not loose or disconnected.




c.

Remove the No. 1 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FUSE BOX>REMOVAL


d.

Disconnect the y1 battery voltage sensor connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A456056C01
0.115,0.885 0.521,1.167 0.406,0.281 1.573,3.927 1.917,4.156 0.344,0.229 1.646,1.729 2.073,1.042 true 2.542,1.708 2.219,1.146 true 2.813,3.604 2.438,3.99 true 1.656,3.604 2.344,3.99 true 0.26,0.083 0.76,0.521 0.5,0.438 10 false *a 0.26,2.115 0.625,2.708 0.365,0.594 10 false *b 0.188,0.948 0.75,1.594 0.563,0.646 10 false A32 1.677,3.948 2.104,4.51 0.427,0.563 10 false y1 2.427,1.75 2.792,2.344 0.365,0.594 10 false CA4L 1.458,1.75 2.021,1.979 0.563,0.229 10 false CA4H 2.875,3.552 3.323,4.167 0.448,0.615 10 false CA1H 1.292,3.542 1.656,4.135 0.365,0.594 10 false CA1L
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-9 (CA4H) - y1-2 (CA1H) Ignition switch off Below 1 Ω
A32-22 (CA4L) - y1-3 (CA1L) Ignition switch off Below 1 Ω
y1-2 (CA1H) - Body ground and other terminals Ignition switch off 10 kΩ or higher
y1-3 (CA1L) - Body ground and other terminals Ignition switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery voltage sensor and hybrid vehicle control ECU is not loose or disconnected and its terminals are not deformed or corroded.



f.

Reconnect the y1 battery voltage sensor connector.


g.

Install the No. 1 hybrid battery shield sub-assembly.


h.

Reconnect the A32 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR