Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  ECU Power Source Circuit  


DESCRIPTION

If the ignition switch is ON, the hybrid vehicle control ECU applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the +B1 and +B2 terminals.

WIRING DIAGRAM

A396293E08
5.156,3.938 7.156,4.292 2,0.354 10 false Hybrid Vehicle Control ECU 1.198,2.354 4.24,2.844 3.042,0.49 10 false No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly 0.135,3.198 1.292,3.646 1.156,0.448 10 false Auxiliary Battery 1.427,1.219 2.094,1.448 0.667,0.229 10 false IGCT-IG 3.323,1.24 4.083,1.458 0.76,0.219 10 false IGCT NO. 1 2.531,1.927 2.969,2.146 0.438,0.219 10 false IGCT 5.833,0.667 6.271,0.885 0.438,0.219 10 false +B1 5.833,1.073 6.271,1.292 0.438,0.219 10 false +B2 5.854,1.51 6.292,1.729 0.438,0.219 10 false MREL 5.844,1.99 6.281,2.208 0.438,0.219 10 false E1 5.844,2.417 6.281,2.635 0.438,0.219 10 false E12 5.844,2.854 6.281,3.073 0.438,0.219 10 false E01 5.854,3.302 6.292,3.521 0.438,0.219 10 false E02 5.458,0.656 5.896,0.875 0.438,0.219 10 false A31 5.448,1.51 5.885,1.729 0.438,0.219 10 false A31 5.448,1.073 5.885,1.292 0.438,0.219 10 false H67 5.448,1.969 5.885,2.188 0.438,0.219 10 false H67 5.448,2.406 5.885,2.625 0.438,0.219 10 false A32 5.448,2.844 5.885,3.063 0.438,0.219 10 false A32 5.458,3.281 5.896,3.5 0.438,0.219 10 false A32 5.49,3.083 5.927,3.302 0.438,0.219 10 false 11 5.49,2.646 5.927,2.865 0.438,0.219 10 false 12 5.5,2.208 5.938,2.427 0.438,0.219 10 false 34 5.542,1.771 5.979,1.99 0.438,0.219 10 false 3 5.531,1.302 5.969,1.521 0.438,0.219 10 false 5 5.542,0.875 5.979,1.094 0.438,0.219 10 false 1 5.49,0.448 5.927,0.667 0.438,0.219 10 false 11 3.354,0.948 3.792,1.167 0.438,0.219 10 false 1 3.844,0.948 4.281,1.167 0.438,0.219 10 false 2 3.073,1.396 3.51,1.615 0.438,0.219 10 false 1 2.177,1.396 2.615,1.615 0.438,0.219 10 false 2 1.854,0.958 2.292,1.177 0.438,0.219 10 false 2 1.385,0.958 1.823,1.177 0.438,0.219 10 false 1 2.177,0.958 2.615,1.177 0.438,0.219 10 false 3 3.083,0.948 3.292,1.167 0.208,0.219 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU (+B1, +B2 VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

C407546C85
1.594,0.24 1.99,0.479 0.396,0.24 5.24,0.219 5.635,0.458 0.396,0.24 0.76,2.146 1.198,1.271 true 6.521,2.188 6.26,1.302 true 1.667,0.271 1.99,0.458 0.323,0.188 10 false A31 5.302,0.26 5.625,0.448 0.323,0.188 10 false H67 0.615,2.188 1.073,2.385 0.458,0.198 10 false +B1 6.417,2.219 6.875,2.417 0.458,0.198 10 false +B2 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A31-11 (+B1) - Body ground Ignition switch ON 11 to 14 V
H67-1 (+B2) - Body ground Ignition switch ON 11 to 14 V



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

NG

3.CHECK HYBRID VEHICLE CONTROL ECU (MREL TERMINAL VOLTAGE)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the A32 and H67 hybrid vehicle control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

A368649C37
3.583,0.729 4,0.958 0.417,0.229 0.385,0.74 0.802,0.969 0.417,0.229 4.677,0.792 4.958,0.229 true 2.365,1.479 2.594,1.125 true 2.771,0.844 2.927,0.323 true 2.635,0.844 2.365,0.292 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 0.469,0.771 0.781,0.927 0.313,0.156 10 false A32 3.667,0.76 3.979,0.917 0.313,0.156 10 false H67 4.99,0.083 5.302,0.24 0.313,0.156 10 false E1 2.135,1.5 2.448,1.656 0.313,0.156 10 false E12 2.938,0.146 3.25,0.302 0.313,0.156 10 false E01 2.104,0.146 2.417,0.302 0.313,0.156 10 false E02
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H67-3 (E1) - Body ground Always Below 1 Ω
A32-12 (E01) - Body ground Always Below 1 Ω
A32-11 (E02) - Body ground Always Below 1 Ω
A32-34 (E12) - Body ground Always Below 1 Ω



c.

Reconnect the A32 and H67 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HYBRID VEHICLE CONTROL ECU (MREL TERMINAL VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

C407546C86
1.563,0.344 1.906,0.594 0.344,0.25 1.917,1.281 2.24,2.281 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.615,0.396 2.073,0.594 0.458,0.198 10 false A31 2.094,2.323 2.708,2.521 0.615,0.198 10 false MREL
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A31-5 (MREL) - Body ground Ignition switch ON 11 to 14 V



c.

Turn the Ignition switch off.


Result:
Proceed to
OK
NG



OK

4.CHECK FUSE (IGCT NO. 1)

NG

4.CHECK FUSE (IGCT NO. 1)
a.
A443444C01
2.719,1.094 1.979,0.76 true 0.146,0.167 0.458,0.365 0.313,0.198 10 false *1 2.76,1.073 3.073,1.271 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT NO. 1 Fuse


Remove the IGCT NO. 1 fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 1 fuse Always Below 1 Ω



c.

Install the IGCT NO. 1 fuse.


Result:
Proceed to
OK
NG



OK

5.CHECK FUSE (IGCT-IG)

NG

11.CHECK HARNESS AND CONNECTOR (IGCT NO. 1 FUSE - HYBRID VEHICLE CONTROL ECU)
5.CHECK FUSE (IGCT-IG)
a.
A443442C01
1.354,0.667 1.958,0.51 true 0.146,0.167 0.458,0.365 0.313,0.198 10 false *1 1.167,0.646 1.479,0.844 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT-IG Fuse


Remove the IGCT-IG fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT-IG fuse Always Below 1 Ω



c.

Install the IGCT-IG fuse.


Result:
Proceed to
OK
NG



OK

6.INSPECT RELAY (IGCT)

NG

12.CHECK HARNESS AND CONNECTOR (NO. 5 FLOOR RELAY BLOCK AND NO. 5 FLOOR JUNCTION BLOCK ASSEMBLY)
6.INSPECT RELAY (IGCT)
a.
A443441C01
0.76,2.188 1.375,1.865 true 0.146,0.167 0.458,0.365 0.313,0.198 10 false *1 0.531,2.146 0.844,2.344 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT Relay


Remove the IGCT relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A253297C01
0.146,0.056 0.409,0.261 0.263,0.205 10 *1
*1 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IGCT NO. 1 FUSE - HYBRID VEHICLE CONTROL ECU)

NG

REPLACE RELAY (IGCT)

7.CHECK HARNESS AND CONNECTOR (IGCT NO. 1 FUSE - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the A31 and H67 hybrid vehicle control ECU connectors.


b.

Remove the IGCT NO. 1 fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

A443449C01
3.49,0.958 3.896,1.25 0.406,0.292 5.802,0.958 6.208,1.25 0.406,0.292 4.26,1.896 4.635,1.375 true 4.635,2.656 5.125,1.938 true 0.521,0.208 0.833,0.365 0.313,0.156 10 false *1 1.896,0.813 2.208,0.969 0.313,0.156 10 false *2 2.542,0.25 2.854,0.406 0.313,0.156 10 false *a 4.5,2.708 4.885,2.969 0.385,0.26 10 false +B2 4.656,1.167 5.042,1.427 0.385,0.26 10 false +B1 5.875,1.042 6.26,1.302 0.385,0.26 10 false H67 3.563,1.021 3.948,1.281 0.385,0.26 10 false A31
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly *2 IGCT NO. 1 Fuse Holder
*a Front view of wire harness connectors
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A31-11 (+B1) - 2 (IGCT NO. 1 fuse holder) Always Below 1 Ω
H67-1 (+B2) - 2 (IGCT NO. 1 fuse holder) Always Below 1 Ω



d.

Reconnect the A31 and H67 hybrid vehicle control ECU connectors.


e.

Install the IGCT NO. 1 fuse.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (NO. 5 FLOOR RELAY BLOCK AND NO. 5 FLOOR JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 5 FLOOR RELAY BLOCK AND NO. 5 FLOOR JUNCTION BLOCK ASSEMBLY)
a.

Remove the IGCT-IG fuse, IGCT NO. 1 fuse and IGCT relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A443450C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 0.396,0.427 0.708,0.583 0.313,0.156 10 false *2 2.688,0.729 3,0.885 0.313,0.156 10 false *3 0.177,1.76 0.49,1.917 0.313,0.156 10 false *4
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT-IG Fuse Holder
*3 IGCT NO. 1 Fuse Holder
*4 IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay holder) - 2 (IGCT-IG fuse holder) Always Below 1 Ω
5 (IGCT relay holder) - 1 (IGCT NO. 1 fuse holder) Always Below 1 Ω



c.

Install the IGCT-IG fuse, IGCT NO. 1 fuse and IGCT relay.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGCT RELAY - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (IGCT RELAY - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Remove the IGCT relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

A443451C01
5.021,0.521 5.5,0.781 0.479,0.26 4.625,2.156 5.063,1.448 true 1.365,0.542 1.677,0.698 0.313,0.156 10 false *1 0.865,1.563 1.177,1.719 0.313,0.156 10 false *2 3.906,0.5 4.219,0.656 0.313,0.156 10 false *a 5.135,0.573 5.615,0.802 0.479,0.229 10 false A31 4.448,2.188 4.927,2.417 0.479,0.229 10 false MREL
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly *2 IGCT Relay Holder
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A31-5 (MREL) - 1 (IGCT relay holder) Always Below 1 Ω
A31-5 (MREL) or 1 (IGCT relay holder) - Body ground and other terminals Always 10 kΩ or higher



d.

Install the IGCT relay.


e.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BODY GROUND)
a.

Remove the IGCT relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A443452C01
0.25,0.177 0.563,0.375 0.313,0.198 10 false *1 0.646,1.771 0.958,1.969 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT relay holder) - Body ground Always Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (IGCT NO. 1 FUSE - HYBRID VEHICLE CONTROL ECU)
a.

Remove the IGCT NO. 1 fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Disconnect the A31 and H67 hybrid vehicle control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

A443449C01
3.49,0.958 3.896,1.25 0.406,0.292 5.802,0.958 6.208,1.25 0.406,0.292 4.26,1.896 4.635,1.375 true 4.635,2.656 5.125,1.938 true 0.521,0.208 0.833,0.365 0.313,0.156 10 false *1 1.896,0.813 2.208,0.969 0.313,0.156 10 false *2 2.542,0.25 2.854,0.406 0.313,0.156 10 false *a 4.5,2.708 4.885,2.969 0.385,0.26 10 false +B2 4.656,1.167 5.042,1.427 0.385,0.26 10 false +B1 5.875,1.042 6.26,1.302 0.385,0.26 10 false H67 3.563,1.021 3.948,1.281 0.385,0.26 10 false A31
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly *2 IGCT NO. 1 Fuse Holder
*a Front view of wire harness connectors
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A31-11 (+B1) or 2 (IGCT NO. 1 fuse holder) - Body ground and other terminals Always 10 kΩ or higher
H67-1 (+B2) or 2 (IGCT NO. 1 fuse holder) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the A31 and H67 hybrid vehicle control ECU connectors.


e.

Install the IGCT NO. 1 fuse.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (IGCT NO. 1)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK HARNESS AND CONNECTOR (NO. 5 FLOOR RELAY BLOCK AND NO. 5 FLOOR JUNCTION BLOCK ASSEMBLY)
a.

Remove the IGCT-IG fuse, IGCT NO. 1 fuse and IGCT relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A443450C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 0.396,0.427 0.708,0.583 0.313,0.156 10 false *2 2.688,0.729 3,0.885 0.313,0.156 10 false *3 0.177,1.76 0.49,1.917 0.313,0.156 10 false *4
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT-IG Fuse Holder
*3 IGCT NO. 1 Fuse Holder
*4 IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay holder) or 2 (IGCT-IG fuse holder) - Body ground and other terminals Always 10 kΩ or higher
5 (IGCT relay holder) or 1 (IGCT NO. 1 fuse holder) - Body ground and other terminals Always 10 kΩ or higher



c.

Install the IGCT-IG fuse, IGCT NO. 1 fuse and IGCT relay.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (IGCT-IG)

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 1)

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT-IG)