Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) T

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  PROBLEM SYMPTOMS TABLE  


Hybrid Control System
Symptom Suspected Area Link
Cannot enter EV mode CAN Communication System Click here
Pattern Select Switch EV Mode Circuit Click here
EV drive mode switch (Pattern select switch assembly) Click here
Combination meter assembly Click here
EV mode indicator light does not illuminate Combination meter assembly Click here
EV drive mode switch (Pattern select switch assembly) Click here
Pattern Select Switch EV Mode Circuit Click here
EV mode indicator light does not turn off Combination meter assembly Click here
EV drive mode switch (Pattern select switch assembly) Click here
Pattern Select Switch EV Mode Circuit Click here
Cannot enter Sport/Eco mode CAN Communication System Click here
Drive mode select switch (No. 1 pattern select switch assembly) Click here
Drive Mode Select Switch Circuit Click here
Combination meter assembly Click here
Sport/Eco mode indicator light does not illuminate Drive mode select switch (No. 1 pattern select switch assembly) Click here
Drive Mode Select Switch Circuit Click here
Combination meter assembly Click here
Sport/Eco mode indicator light does not turn off Drive mode select switch (No. 1 pattern select switch assembly) Click here
Drive Mode Select Switch Circuit Click here
Combination meter assembly Click here
Hunting (Poor idle) Check for Diagnosis Related Information*3 Click here
Click here
Drive Start Control Click here
Hesitation and/or poor acceleration Check for Diagnosis Related Information*3 Click here
Click here
Brake Override System Click here
Drive Start Control Click here
Shift range position cannot be changed by shifting to "+" or "-" Transmission Control Switch Circuit Click here
Shift position indicator is malfunctioning Indicator circuit Click here
Ignition switch does not turn ON (READY) Check Vehicle Control History (wrong assembly confirmation)*1 Click here
Entry and Start System (for Start Function) Click here
ECU Power Source Circuit (Hybrid Control System) Click here
Hybrid vehicle control ECU Click here
ECM Click here
Loud rattle from hybrid vehicle transaxle Check idle learning Click here
Transmission input damper assembly Click here
Hybrid vehicle transaxle assembly Click here
Engine misfire -
"Maintenance Required for Traction Battery Cooling Parts See Owner's Manual" is displayed on the multi-information display.*2 1. Make sure the HV battery cooling system intake port is not blocked. -
2. Make sure there are no gaps between the connecting parts of the ducts. -
3. Clean the No. 2 hybrid battery intake filter.
Check for entry of foreign matter.
Click here
4. Clear the DTCs to reset the learning values even if no DTCs are stored. Click here
Abnormal sound is heard from the area around the No. 1 hybrid battery intake duct. 1. Make sure the HV battery cooling system intake port is not blocked. -
2. Make sure there are no gaps between the connecting parts of the ducts. -
3. Clean the No. 2 hybrid battery intake filter.
Check for entry of foreign matter.
Click here
4. Clear the DTCs to reset the learning values even if no DTCs are stored. Click here
Engine stops and starts less frequently. Check Vehicle Control History
(Limit to Charge / Discharge Control Value by Hybrid Battery Temperature High)
Click here
Engine speed returns to idle slowly after accelerator pedal is fully released. Check Vehicle Control History
(Limit to Charge / Discharge Control Value by Hybrid Battery Temperature High)
Click here

*1: Check Vehicle Control History (wrong assembly confirmation)

1.

Using the GTS, check the Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>VEHICLE CONTROL HISTORY

HINT:

If "Hybrid Battery Pack Sensor Module Mismatch" is displayed, the wrong type of battery voltage sensor is installed.


2.

If the battery voltage sensor had been replaced just before the malfunction occurred, check the part number of the battery voltage sensor.

HINT:
·

The type of battery voltage sensor to be used varies depending on the vehicle model.

·

If the wrong type of battery voltage sensor is installed, the ignition switch cannot be turned to ON (READY).



3.

After installing the battery voltage sensor, perform the following to check that the ignition switch can be turned to ON (READY).

(a)

Turn the ignition switch to ON (READY).

(b)

Turn the ignition switch off and wait for 2 minutes or more.

(c)

Turn the ignition switch to ON (READY) again.



*2: If the battery cooling blower assembly malfunctions, DTC P0A8100, P0A8111, P0A8115, P0A814B, P0A8196, P0A8198, P0A9600, P0A9611, P0A9615, P0A964B, P0A9696 or P0A9698 will be stored. If only "Maintenance Required for Traction Battery Cooling Parts See Owner's Manual" is displayed on the multi-information display, only perform the inspection of the HV battery cooling system intake port, filter and duct.

*3: If any of the following Diagnosis Related Information items are output, perform troubleshooting for the corresponding DTCs.

Result
Result Link
Hybrid Control System P312387 (Click here)
Motor Generator Control System P31241F (Click here)
P312487