Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P253012  IG2 Signal Circuit Short to Auxiliary Battery  


DESCRIPTION

The hybrid vehicle control ECU compares the IG2 signal to the IG control status signal sent from the certification ECU (smart key ECU assembly) to detect a stuck on malfunction of the IG2 signal.

HINT:

If DTC P253012 is stored, the ignition switch will turn off (READY off).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P253012 IG2 Signal Circuit Short to Auxiliary Battery The IG2 signal of the hybrid vehicle control ECU and the IG switch signal sent from the certification ECU (smart key ECU assembly) do not match.
(1 trip detection logic)
·

Auxiliary battery

·

Certification ECU (smart key ECU assembly)

·

Hybrid vehicle control ECU

·

ECM

·

IG2 NO. 1 relay

·

Wire harness or connector


Does not come on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and wait for 15 seconds or more.

6.

Turn the ignition switch off and wait for 2 minutes or more.

7.

Turn the ignition switch to ON and turn the GTS on.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A456055E01
0.771,3.292 2.229,3.646 1.458,0.354 10 false Auxiliary Battery 1.125,0.719 1.823,0.917 0.698,0.198 10 false IG2-MAIN 2.448,1.302 3.365,1.5 0.917,0.198 10 false IG2 NO. 1 3.51,0.698 4.969,0.99 1.458,0.292 10 false ECU-IG2 NO. 1 5.281,4.146 7.125,4.5 1.844,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.271,3.99 5.573,4.219 0.302,0.229 10 false H48 5.781,2.896 6.083,3.125 0.302,0.229 10 false A27 5.781,3.073 7.021,3.563 1.24,0.49 10 false ECM 5.865,2.521 6.781,2.719 0.917,0.198 10 false E1 5.865,2.135 6.781,2.333 0.917,0.198 10 false IGSW 5.833,3.688 6.75,3.885 0.917,0.198 10 false IG1D 5.615,2.417 5.917,2.646 0.302,0.229 10 false 10 5.667,2.031 5.969,2.26 0.302,0.229 10 false 2 5.563,3.594 5.865,3.823 0.302,0.229 10 false 17 5.292,1.531 7.115,1.927 1.823,0.396 10 false Hybrid Vehicle Control ECU 5.875,0.917 6.229,1.104 0.354,0.188 10 false E01 5.865,0.438 6.198,0.635 0.333,0.198 10 false IG2 5.292,1.375 5.594,1.604 0.302,0.229 10 false A32 5.583,0.865 5.885,1.094 0.302,0.229 10 false 12 5.594,0.427 5.896,0.656 0.302,0.229 10 false 35 3.729,0.417 4.031,0.646 0.302,0.229 10 false 1 1.594,0.438 1.896,0.667 0.302,0.229 10 false 2 4.083,0.417 4.385,0.646 0.302,0.229 10 false 2 1.188,0.438 1.49,0.667 0.302,0.229 10 false 1 3.146,0.438 3.448,0.667 0.302,0.229 10 false 5 2.365,0.875 2.667,1.104 0.302,0.229 10 false 2 2.365,0.448 2.667,0.677 0.302,0.229 10 false 3 3.135,0.885 3.438,1.115 0.302,0.229 10 false 1 0.604,2.198 1.302,2.396 0.698,0.198 10 false MAIN

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE
a.

Turn the ignition switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


b.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 20°C (68°F), Ignition switch off 12.0 V or higher


Result:
Proceed to
OK
NG




OK

3.CLEAR DTC

NG

2.CHARGE OR REPLACE AUXILIARY BATTERY
2.CHARGE OR REPLACE AUXILIARY BATTERY
a.

Charge or replace the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Turn the ignition switch to ON and wait for 15 seconds or more.


b.

Turn the ignition switch off and wait for 2 minutes or more.


c.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P253012 is output. A
P253012 is not output. B



d.

Turn the ignition switch off.



A

5.CHECK DTC OUTPUT (HYBRID CONTROL)

B

5.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
U012987, U014087, U015187, U016487, U110787 or U117087 is output A
Other than above B



b.

Turn the ignition switch off.



A

6.CHECK HYBRID VEHICLE CONTROL ECU

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HYBRID VEHICLE CONTROL ECU
a.
A456044C04
0.104,0.99 0.469,1.229 0.365,0.24 2.656,1.427 2.75,1.844 true 2.719,1.198 3.021,1.458 true 0.177,1.021 0.49,1.219 0.313,0.198 10 false A32 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 2.688,1.885 3.021,2.125 0.333,0.24 10 false IG2 3.063,1.427 3.396,1.667 0.333,0.24 10 false E01
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the A32 hybrid vehicle control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Condition:
Tester Connection Condition
A32-35 (IG2) - A32-12 (E01) Ignition switch off



c.

Reconnect the A32 hybrid vehicle control ECU connector.


Result:
Result Proceed to
9 V or higher A
Below 9 V B



A

7.CHECK ECM

B

7.CHECK ECM
a.
A456044C04
0.104,0.99 0.469,1.229 0.365,0.24 2.656,1.427 2.75,1.844 true 2.719,1.198 3.021,1.458 true 0.177,1.021 0.49,1.219 0.313,0.198 10 false A32 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 2.688,1.885 3.021,2.125 0.333,0.24 10 false IG2 3.063,1.427 3.396,1.667 0.333,0.24 10 false E01
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the A32 hybrid vehicle control ECU connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Condition:
Tester Connection Condition
A32-35 (IG2) - A32-12 (E01) Ignition switch off



d.

Reconnect the A27 ECM connector.


e.

Reconnect the A32 hybrid vehicle control ECU connector.


Result:
Result Proceed to
9 V or higher A
Below 9 V B



A

8.INSPECT RELAY (IG2 NO. 1)

B

8.INSPECT RELAY (IG2 NO. 1)
a.
A456066C01
2.615,1.729 1.844,1.229 true 0.208,0.135 0.521,0.333 0.313,0.198 10 false *1 2.688,1.677 3,1.875 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 IG2 NO. 1 Relay


Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
B060778N68
2.51,1.625 2.844,1.625 true 2.521,1.125 2.854,1.125 true 2.615,0.583 2.792,0.271 2.792,0.271 2.948,0.271 true 2.021,0.573 1.865,0.26 1.865,0.26 1.719,0.26 true 2.896,1.552 3.406,2.167 0.51,0.615 10 true 3 2.906,1.042 3.104,1.24 0.198,0.198 10 false 5 3.01,0.177 3.208,0.375 0.198,0.198 10 false 2 1.573,0.177 1.771,0.375 0.198,0.198 10 false 1 1.219,0.76 1.417,0.958 0.198,0.198 10 false 5 1.229,1.302 1.427,1.5 0.198,0.198 10 false 2 0.208,0.76 0.417,0.927 0.208,0.167 10 false 3 0.219,1.302 0.417,1.5 0.198,0.198 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the IG2 NO. 1 relay.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IG2 NO. 1 RELAY)

NG

REPLACE RELAY (IG2 NO. 1)

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IG2 NO. 1 RELAY)
a.

Disconnect the A32 hybrid vehicle control ECU connector.


b.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.
A456044C05
0.104,0.99 0.479,1.271 0.375,0.281 2.667,1.438 2.75,1.833 true 0.188,1.042 0.5,1.24 0.313,0.198 10 false A32 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 2.688,1.875 3.021,2.115 0.333,0.24 10 false IG2
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32-35 (IG2) - Body ground Ignition switch off 1 V or less



d.

Install the IG2 NO. 1 relay.


e.

Reconnect the A32 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the IG2 NO. 1 relay.


ii.

When the ignition switch is ON (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the IG2 NO. 1 relay.




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR