Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  Inverter Low-voltage Circuit  


DESCRIPTION

The cause of the malfunction may be the low-voltage circuit.

Check whether there is an open circuit in the inverter +B low-voltage power source system or a problem in the communication between the hybrid vehicle control ECU and inverter.

Related Parts Check
Area Inspection
Inverter +B low-voltage power source system check Check for inverter overcurrent malfunction.
Communication malfunction between hybrid vehicle control ECU and MG-ECU inside inverter with converter assembly Check for inverter overcurrent malfunction due to communication malfunction.
Check for short to ground in inverter +B low-voltage power source system -

WIRING DIAGRAM

A368540E42
6.115,1.531 7.156,2.208 1.042,0.677 10 false from IGCT Relay 6.427,0.958 6.781,1.323 0.354,0.365 10 false PCU 5.469,2.271 5.958,2.573 0.49,0.302 10 false GND2 5.49,1.844 5.979,2.146 0.49,0.302 10 false GND1 5.656,0.802 5.99,1.094 0.333,0.292 10 false +B 5.615,1.24 5.948,1.531 0.333,0.292 10 false +B2 4.198,0.844 4.688,1.146 0.49,0.302 10 false HMCL 2.167,0.896 2.656,1.198 0.49,0.302 10 false HMCL 2.167,1.354 2.656,1.656 0.49,0.302 10 false HMCH 4.188,1.333 4.677,1.635 0.49,0.302 10 false HMCH 4.042,2.927 6.104,3.552 2.063,0.625 10 false Inverter with Converter Assembly 5.938,2.146 6.427,2.448 0.49,0.302 10 false 8 2.698,0.979 3.188,1.281 0.49,0.302 10 false A31 5.938,1.115 6.427,1.417 0.49,0.302 10 false 35 5.927,1.708 6.417,2.01 0.49,0.302 10 false 9 5.948,0.667 6.438,0.969 0.49,0.302 10 false 36 6.667,0.656 6.979,0.948 0.313,0.292 10 false 1 6.396,0.656 6.708,0.948 0.313,0.292 10 false 2 4.01,0.854 4.5,1.156 0.49,0.302 10 false 4 4,1.323 4.49,1.625 0.49,0.302 10 false 3 4.063,2.74 4.552,3.042 0.49,0.302 10 false A55 2.688,1.469 3.177,1.771 0.49,0.302 10 false A31 2.677,2.135 3.167,2.438 0.49,0.302 10 false A31 0.552,1.792 1.042,2.094 0.49,0.302 10 false H67 0.542,2.313 1.031,2.615 0.49,0.302 10 false A32 2.719,0.76 3.208,1.063 0.49,0.302 10 false 14 2.75,1.24 3.24,1.542 0.49,0.302 10 false 4 2.698,1.927 3.188,2.229 0.49,0.302 10 false 13 4.01,2.01 4.5,2.313 0.49,0.302 10 false 2 4.198,2.125 4.958,2.427 0.76,0.302 10 false DRN1 2.208,2.125 2.969,2.427 0.76,0.302 10 false DRN5 0.917,2.74 3.927,3.167 3.01,0.427 10 false Hybrid Vehicle Control ECU 0.938,1.802 1.427,2.104 0.49,0.302 10 false E1 0.948,2.323 1.438,2.625 0.49,0.302 10 false E12 0.594,2.115 0.896,2.385 0.302,0.271 10 false 34 0.646,1.604 0.948,1.875 0.302,0.271 10 false 3 4.958,1.25 5.219,1.521 0.26,0.271 10 false * 1.802,1.24 2.063,1.51 0.26,0.271 10 false * 0.333,3.427 2.104,3.75 1.771,0.323 10 false *: Approximately 120 Ω

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK FUSE (PCU)
a.
A456867C01
2.104,1.135 2.625,1.354 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *1 2.688,1.292 3,1.49 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 PCU Fuse


Remove the PCU fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PCU fuse Always Below 1 Ω



c.

Install the PCU fuse.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.
C412486C11
0.292,0.885 0.667,1.146 0.375,0.26 1.99,0.885 2.604,0.302 true 1.875,0.896 1.906,0.292 true 2,1.292 2.719,1.833 true 1.885,1.281 2.167,1.906 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.365,0.948 0.823,1.146 0.458,0.198 10 false A55 2.708,1.844 3.021,2.042 0.313,0.198 10 false +B 2.104,1.938 2.427,2.115 0.323,0.177 10 false +B2 2.635,0.135 3.094,0.333 0.458,0.198 10 false GND1 1.74,0.104 2.354,0.302 0.615,0.198 10 false GND2
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-9 (GND1) - Body ground Ignition switch off Below 1 Ω
A55-8 (GND2) - Body ground Ignition switch off Below 1 Ω



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-36 (+B) - Body ground Ignition switch ON Same as auxiliary battery voltage
A55-35 (+B2) - Body ground Ignition switch ON Same as auxiliary battery voltage


NOTICE:

Turning the ignition switch to ON with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


i.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.

Disconnect the A31 hybrid vehicle control ECU connector.


d.
C412487C07
0.073,3.385 0.438,3.635 0.365,0.25 0.135,1.198 0.5,1.448 0.365,0.25 1.521,1.146 1.49,0.479 true 1.625,1.156 2.417,0.469 true 1.375,3.458 2.052,2.802 true 1.458,3.698 1.917,4.313 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.104,2.438 0.417,2.635 0.313,0.198 10 false *b 0.188,1.24 0.646,1.438 0.458,0.198 10 false A55 0.135,3.438 0.594,3.635 0.458,0.198 10 false A31 1.25,0.292 1.865,0.49 0.615,0.198 10 false HMCH 2.469,0.333 3.083,0.531 0.615,0.198 10 false HMCL 1.833,4.375 2.448,4.573 0.615,0.198 10 false HMCL 2.115,2.667 2.729,2.865 0.615,0.198 10 false HMCH
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A55-3 (HMCH) - A31-4 (HMCH) Ignition switch off Below 1 Ω
A55-4 (HMCL) - A31-14 (HMCL) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A55-3 (HMCH) or A31-4 (HMCH) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A55-4 (HMCL) or A31-14 (HMCL) - Body ground and other terminals Ignition switch off 10 kΩ or higher



e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-3 (HMCH) or A31-4 (HMCH) - Body ground and other terminals Ignition switch ON Below 1 V
A55-4 (HMCL) or A31-14 (HMCL) - Body ground and other terminals Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the hybrid vehicle control ECU and inverter with converter assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


j.

Reconnect the A31 hybrid vehicle control ECU connector.


k.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

A365590C41
1.594,0.333 1.948,0.583 0.354,0.25 2.063,1.292 2.625,2.365 true 1.979,1.396 1.646,2.333 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.646,0.375 2.104,0.573 0.458,0.198 10 false A31 2.438,2.417 3.052,2.615 0.615,0.198 10 false HMCH 1.438,2.417 2.052,2.615 0.615,0.198 10 false HMCL
*a Component without harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A31-14 (HMCL) - A31-4 (HMCH) Ignition switch off 80 to 170 Ω



c.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

INVERTER LOW-VOLTAGE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.
C412486C12
0.292,0.885 0.667,1.146 0.375,0.26 2,1.292 2.719,1.833 true 1.885,1.281 2.167,1.906 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.365,0.948 0.823,1.146 0.458,0.198 10 false A55 2.708,1.844 3.021,2.042 0.313,0.198 10 false +B 2.104,1.938 2.427,2.115 0.323,0.177 10 false +B2
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-36 (+B) - Body ground Ignition switch off 10 kΩ or higher
A55-35 (+B2) - Body ground Ignition switch off 10 kΩ or higher



d.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

REPLACE FUSE (PCU)

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PCU)