Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P0A8111  Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground  P0A814B  Hybrid/EV Battery Cooling Fan 1 Over Temperature  P0A9611  Hybrid/EV Battery Cooling Fan 2 Circuit Short to Ground  P0A964B  Hybrid/EV Battery Cooling Fan 2 Over Temperature  


DESCRIPTION

The battery cooling blower assembly speed is controlled by the battery voltage sensor. Power is supplied to the battery cooling blower assembly when the MREL terminal of the hybrid vehicle control ECU turns on the IGCT relay. The battery voltage sensor sends command signals (SI0 and SI1) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The frequency (FP0 and FP1) of the battery cooling blower assembly is sent to the hybrid vehicle control ECU via the battery voltage sensor as a monitor signal using CAN communication.

A449769E01
0.344,1.875 1.771,2.615 1.427,0.74 10 false Battery Cooling Blower Assembly (No. 0) 3.167,4.177 4.75,4.531 1.583,0.354 10 false Battery Voltage Sensor 1.833,0.781 3.542,1.771 1.708,0.99 10 false SI0 (Command Signal) 1.885,1.573 3.521,2.833 1.635,1.26 10 false FP0 (Monitor Signal) 1.823,3 3.531,3.99 1.708,0.99 10 false SI1 (Command Signal) 1.885,3.781 3.542,4.479 1.656,0.698 10 false FP1 (Monitor Signal) 0.365,4.115 1.792,4.552 1.427,0.438 10 false Battery Cooling Blower Assembly (No. 1) 5.396,4.188 7.125,4.521 1.729,0.333 10 false Hybrid Vehicle Control ECU 4.406,2.396 6.135,2.729 1.729,0.333 10 false CAN Communication

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A8111 Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground Both of the following conditions are met:
·

The speed calculated based on the battery cooling blower assembly (No. 0) output frequency is not within the target control speed range.

·

The battery cooling blower assembly (No. 0) speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(2 trip detection logic)
·

Battery voltage sensor

·

Battery cooling blower assembly (No. 0)

·

BATT FAN NO. 1 fuse

·

BATT FAN NO. 1 relay

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0A814B Hybrid/EV Battery Cooling Fan 1 Over Temperature Both of the following conditions are met:
·

The HV battery temperature is high and the speed calculated based on the battery cooling blower assembly (No. 0) output frequency is not within the target control speed range.

·

The HV battery temperature is high and the battery cooling blower assembly (No. 0) speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(1 trip detection logic)
·

Battery voltage sensor

·

Battery cooling blower assembly (No. 0)

·

BATT FAN NO. 1 fuse

·

BATT FAN NO. 1 relay

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0A9611 Hybrid/EV Battery Cooling Fan 2 Circuit Short to Ground Both of the following conditions are met:
·

The speed calculated based on the battery cooling blower assembly (No. 1) output frequency is not within the target control speed range.

·

The battery cooling blower assembly (No. 1) speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(2 trip detection logic)
·

Battery voltage sensor

·

Battery cooling blower assembly (No. 1)

·

BATT FAN NO. 2 fuse

·

BATT FAN NO. 2 relay

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0A964B Hybrid/EV Battery Cooling Fan 2 Over Temperature Both of the following conditions are met:
·

The HV battery temperature is high and the speed calculated based on the battery cooling blower assembly (No. 1) output frequency is not within the target control speed range.

·

The HV battery temperature is high and the battery cooling blower assembly (No. 1) speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(1 trip detection logic)
·

Battery voltage sensor

·

Battery cooling blower assembly (No. 1)

·

BATT FAN NO. 2 fuse

·

BATT FAN NO. 2 relay

·

Wire harness or connector


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A8111
·

Hybrid Battery Cooling Fan 1 Drive Request

·

Hybrid Battery Cooling Fan 1 Drive Status

·

Hybrid Battery Cooling Fan 1 Frequency


P0A814B
P0A9611
·

Hybrid/EV Battery Cooling Fan 2 Drive Request

·

Hybrid/EV Battery Cooling Fan 2 Drive Status

·

Hybrid/EV Battery Cooling Fan 2 Frequency


P0A964B

The following items can be helpful when performing repairs:

Data List
·

Hybrid Battery Temperature 1 to 6

·

BATT Voltage


HINT:
·

"Hybrid Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly (No. 0) is operating and its value changes in proportion to the battery cooling blower assembly (No. 0) speed.

·

"Hybrid/EV Battery Cooling Fan 2 Frequency" is detected when the battery cooling blower assembly (No. 1) is operating and its value changes in proportion to the battery cooling blower assembly (No. 1) speed.



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

7.

Select fan mode 1 and operate the battery cooling blower assembly and wait for 60 seconds or more.

HINT:

Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.


8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A449785E02
5.875,0.417 6.333,0.615 0.458,0.198 10 false FP0 5.885,0.906 6.344,1.104 0.458,0.198 10 false SI0 5.875,2.375 6.333,2.573 0.458,0.198 10 false FP1 5.875,2.885 6.333,3.083 0.458,0.198 10 false SI1 5.875,5.969 6.333,6.167 0.458,0.198 10 false GND 5.146,0.396 5.604,0.594 0.458,0.198 10 false FP0 5.198,0.906 5.656,1.104 0.458,0.198 10 false SI0 4.156,0.396 4.615,0.594 0.458,0.198 10 false IG0 4.156,0.896 4.615,1.094 0.458,0.198 10 false GND0 5.156,2.375 5.615,2.573 0.458,0.198 10 false FP1 5.208,2.885 5.667,3.083 0.458,0.198 10 false SI1 4.177,2.375 4.635,2.573 0.458,0.198 10 false IG1 4.156,2.885 4.615,3.083 0.458,0.198 10 false GND1 1.198,0.667 2.375,1.052 1.177,0.385 10 false BATT FAN NO. 1 2.458,1.25 3.635,1.635 1.177,0.385 10 false BATT FAN NO. 1 2.448,3.229 3.625,3.615 1.177,0.385 10 false BATT FAN NO. 2 1.167,2.635 2.344,3.021 1.177,0.385 10 false BATT FAN NO. 2 2.865,4.635 4.042,5.021 1.177,0.385 10 false IGCT 1.26,4.094 2.438,4.479 1.177,0.385 10 false IGCT-IG 1.552,4.667 2.219,4.896 0.667,0.229 10 false MREL 0.083,6.458 1.948,6.823 1.865,0.365 10 false from Auxiliary Battery 0.563,6.01 2.542,6.292 1.979,0.281 10 false Hybrid Vehicle Control ECU 5.563,6.323 7.083,6.625 1.521,0.302 10 false Battery Voltage Sensor 4.073,3.5 5.573,4.01 1.5,0.51 10 false Battery Cooling Blower Assembly (No. 1) 4.083,1.49 5.583,2 1.5,0.51 10 false Battery Cooling Blower Assembly (No. 0) 2.115,4.583 2.313,4.802 0.198,0.219 10 false 5 2.042,4.781 2.396,5.031 0.354,0.25 10 false A31 2.542,4.281 2.74,4.5 0.198,0.219 10 false 1 3.385,4.281 3.583,4.5 0.198,0.219 10 false 2 2.552,3.865 2.75,4.083 0.198,0.219 10 false 3 3.375,3.865 3.573,4.083 0.198,0.219 10 false 5 2.75,3.646 3.719,3.885 0.969,0.24 10 false IGCT NO. 2 2.583,2.896 2.781,3.115 0.198,0.219 10 false 1 2.594,0.917 2.792,1.135 0.198,0.219 10 false 1 3.323,2.906 3.521,3.125 0.198,0.219 10 false 2 3.323,0.917 3.521,1.135 0.198,0.219 10 false 2 2.594,0.406 2.792,0.625 0.198,0.219 10 false 3 2.583,2.375 2.781,2.594 0.198,0.219 10 false 3 3.323,2.375 3.521,2.594 0.198,0.219 10 false 5 3.313,0.396 3.51,0.615 0.198,0.219 10 false 5 4,0.396 4.198,0.615 0.198,0.219 10 false 1 4,2.375 4.198,2.594 0.198,0.219 10 false 1 4,2.885 4.198,3.104 0.198,0.219 10 false 4 4,0.917 4.198,1.135 0.198,0.219 10 false 4 5.469,2.375 5.667,2.594 0.198,0.219 10 false 2 5.479,0.396 5.677,0.615 0.198,0.219 10 false 2 5.469,2.885 5.667,3.104 0.198,0.219 10 false 3 5.479,0.906 5.677,1.125 0.198,0.219 10 false 3 4.083,1.323 4.448,1.552 0.365,0.229 10 false M49 4.073,3.344 4.438,3.573 0.365,0.229 10 false M50 5.635,0.417 5.833,0.635 0.198,0.219 10 false 11 5.708,0.906 5.906,1.125 0.198,0.219 10 false 5 5.625,2.375 5.823,2.594 0.198,0.219 10 false 12 5.698,2.885 5.896,3.104 0.198,0.219 10 false 6 5.677,5.854 6.052,6.188 0.375,0.333 10 false 7 5.573,6.135 6.031,6.333 0.458,0.198 10 false y1 5.677,5.5 6.052,5.833 0.375,0.333 10 false 3 5.677,5.063 6.052,5.396 0.375,0.333 10 false 2 2.031,5.229 2.385,5.479 0.354,0.25 10 false A32 2.031,5.656 2.385,5.906 0.354,0.25 10 false A32 1.563,5.219 2.229,5.448 0.667,0.229 10 false CA4H 1.583,5.646 2.25,5.875 0.667,0.229 10 false CA4L 2.125,5.042 2.323,5.26 0.198,0.219 10 false 9 2.094,5.469 2.292,5.688 0.198,0.219 10 false 22 5.865,5.198 6.531,5.427 0.667,0.229 10 false CA1H 5.875,5.635 6.542,5.865 0.667,0.229 10 false CA1L 1.844,0.406 2.042,0.625 0.198,0.219 10 false 2 1.365,0.406 1.563,0.625 0.198,0.219 10 false 1 1.833,2.375 2.031,2.594 0.198,0.219 10 false 2 1.375,2.375 1.573,2.594 0.198,0.219 10 false 1 3.271,3.417 3.469,3.635 0.198,0.219 10 false 1 2.823,3.406 3.021,3.625 0.198,0.219 10 false 2 2.542,6.427 4.521,6.708 1.979,0.281 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:

As the battery cooling blower assembly speed is excessively low, there is a possibility of an open or short to ground in connected circuits, or motor locking.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00 or P0AFC96 is not output. A
P0AFC00 or P0AFC96 is output. B


b.

Turn the ignition switch off.



A

2.CHECK DTC

B

2.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
P0A8111 or P0A814B is also output. A
P0A9611 or P0A964B is also output. B



A

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID BATTERY COOLING FAN)

B

27.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID BATTERY COOLING FAN)
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID BATTERY COOLING FAN)
a.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

b.

Select fan mode 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly (No. 0).

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check if the fan operates and air is sucked in. In accordance with fail-safe system operation, the battery voltage sensor sends a command to operate the battery cooling blower assembly (No. 0).


Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

c.

Check that the battery cooling blower assembly (No. 0) operates, air is sucked into the inlet duct and the operation sound is normal.

HINT:

The battery cooling blower assembly (No. 0) may not stop even when turning the cooling fan off in the "Control the Hybrid Battery Cooling Fan" Active Test. This is due to HV system control and is not a malfunction.


OK:

The battery cooling blower assembly (No. 0) operates.



d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

NG

8.CHECK FUSE (BATT FAN NO. 1)
4.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Disconnect the y1 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A449750N01
2.135,1.198 2.521,1.438 0.385,0.24 2.156,1.219 2.49,1.417 0.333,0.198 10 true M49

Disconnect the M49 battery cooling blower assembly (No. 0) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A449752C01
1.396,1.802 1.854,2.073 0.458,0.271 0.833,3.542 1.292,3.813 0.458,0.271 1.875,3.635 2.219,4.26 true 1.906,2.573 2.219,2.01 true 0.135,0.115 0.594,0.604 0.458,0.49 10 false *a 0.24,3.021 0.604,3.323 0.365,0.302 10 false *b 0.938,3.594 1.458,3.896 0.521,0.302 10 false M49 1.563,1.844 2.083,2.146 0.521,0.302 10 false y1 2.135,4.281 2.5,4.583 0.365,0.302 10 false FP0 1.792,2.594 2.156,2.896 0.365,0.302 10 false FP0
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 0))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-11 (FP0) - M49-2 (FP0) Ignition switch off Below 1 Ω
y1-11 (FP0) - Body ground and other terminals Ignition switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the ignition switch to ON.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
y1-11 (FP0) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check the condition of each wire harness and each connector between the battery voltage sensor connector and battery cooling blower assembly (No. 0).



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the M49 battery cooling blower assembly (No. 0) connector.


l.

Reconnect the y1 battery voltage sensor connector.


m.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (HYBRID BATTERY COOLING FAN 1 FREQUENCY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (HYBRID BATTERY COOLING FAN 1 FREQUENCY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly (No. 0).

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the battery voltage sensor sends a command to operate the battery cooling fan assembly (No. 0).


Powertrain > Hybrid Control > Active Test
Active Test Display
Control the Hybrid Battery Cooling Fan
Data List Display
Hybrid Battery Cooling Fan 1 Frequency
50004 397 2 157

f.
A449753C01
2.115,0.229 2.552,0.458 0.438,0.229 1.99,1.781 2.229,1.021 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.25 2.656,0.563 0.396,0.313 10 false y1 1.823,1.813 2.156,2.073 0.333,0.26 10 false FP0 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


While the battery cooling blower assembly (No. 0) is operating, compare the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.

Specified Condition:
Tester Connection Condition
y1-11 (FP0) - y1-7 (GND) Battery cooling blower assembly (No. 0) is operating.


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.



Result:
Result Proceed to
Both of the values in the Data List (Hybrid Battery Cooling Fan 1 Frequency) and the actual measured value at the battery voltage sensor connector are 0 Hz. A
Other than above B


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Install the HV battery junction block assembly.



A

6.CHECK BATTERY VOLTAGE SENSOR

B

7.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
6.CHECK BATTERY VOLTAGE SENSOR
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.
A449750N01
2.135,1.198 2.521,1.438 0.385,0.24 2.156,1.219 2.49,1.417 0.333,0.198 10 true M49

Disconnect the M49 battery cooling blower assembly (No. 0) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.
A456739C03
1.5,0.271 1.938,0.552 0.438,0.281 1.833,1.156 2.313,1.313 true 2.25,1.688 1.833,1.344 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.615,0.344 2.271,0.865 0.656,0.521 10 false M49 2.365,1.26 2.802,1.51 0.438,0.25 10 false FP0 2.292,1.667 2.823,1.896 0.531,0.229 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 0))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M49-2 (FP0) - M49-4 (GND0) Ignition switch ON 4.5 to 5.5 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the M49 battery cooling blower assembly (No. 0) connector.


j.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

NG

7.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly (No. 0).

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the battery voltage sensor sends a command to operate the battery cooling blower assembly (No. 0).


Powertrain > Hybrid Control > Active Test
Active Test Display
Control the Hybrid Battery Cooling Fan
Data List Display
Hybrid Battery Cooling Fan 1 Frequency
50004 397 2 157

f.
A449753C01
2.115,0.229 2.552,0.458 0.438,0.229 1.99,1.781 2.229,1.021 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.25 2.656,0.563 0.396,0.313 10 false y1 1.823,1.813 2.156,2.073 0.333,0.26 10 false FP0 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


While the battery cooling blower assembly (No. 0) is operating, compare the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.

Specified Condition:
Tester Connection Condition Specified Condition
y1-11 (FP0) - y1-7 (GND) Battery cooling blower assembly (No. 0) is operating. Difference between the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) and the actual measured value at the battery voltage sensor connector is 10% or less.


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

NG

8.CHECK FUSE (BATT FAN NO. 1)
a.
A449801C01
2.365,0.667 2.813,0.875 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *1 2.854,0.833 3.167,1.031 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 1 Fuse


Remove the BATT FAN NO. 1 fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
BATT FAN NO. 1 fuse Always Below 1 Ω



c.

Install the BATT FAN NO. 1 fuse.


Result:
Proceed to
OK
NG



OK

9.CHECK RELAY (BATT FAN NO. 1)

NG

21.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 FUSE - BATT FAN NO. 1 RELAY)
9.CHECK RELAY (BATT FAN NO. 1)
a.
A449802C01
0.635,2.708 1.219,2.396 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *1 0.479,2.646 0.792,2.844 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 1 Relay


Remove the BATT FAN NO. 1 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
B060778N68
2.51,1.625 2.844,1.625 true 2.521,1.125 2.854,1.125 true 2.615,0.583 2.792,0.271 2.792,0.271 2.948,0.271 true 2.021,0.573 1.865,0.26 1.865,0.26 1.719,0.26 true 2.896,1.552 3.406,2.167 0.51,0.615 10 true 3 2.906,1.042 3.104,1.24 0.198,0.198 10 false 5 3.01,0.177 3.208,0.375 0.198,0.198 10 false 2 1.573,0.177 1.771,0.375 0.198,0.198 10 false 1 1.219,0.76 1.417,0.958 0.198,0.198 10 false 5 1.229,1.302 1.427,1.5 0.198,0.198 10 false 2 0.208,0.76 0.417,0.927 0.208,0.167 10 false 3 0.219,1.302 0.417,1.5 0.198,0.198 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the BATT FAN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 FUSE - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

NG

REPLACE RELAY (BATT FAN NO. 1)

10.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 FUSE - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.
A449750N01
2.135,1.198 2.521,1.438 0.385,0.24 2.156,1.219 2.49,1.417 0.333,0.198 10 true M49

Disconnect the M49 battery cooling blower assembly (No. 0) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Connect the GTS to the DLC3.


f.

Turn the ignition switch to ON.


g.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


h.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

i.
A456739C01
1.5,0.271 1.938,0.552 0.438,0.281 1.281,1.74 1.615,1.167 true 1.823,1.344 2.229,1.76 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.604,0.344 2.26,0.865 0.656,0.521 10 false M49 1.156,1.76 1.604,2.063 0.448,0.302 10 false IG0 2.094,1.76 2.729,2.052 0.635,0.292 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 0))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M49-1 (IG0) - M49-4 (GND0) Ignition switch ON 11 to 14 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)

·

Fuse condition (before and after removing fuse(s)) (IG circuit)

·

Connection condition of connectors (IG circuit)

·

Wire harness condition (IG circuit)

·

Wire harness condition (GND circuit)




j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Reconnect the M49 battery cooling blower assembly (No. 0) connector.


m.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

NG

15.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY (NO. 0) - BODY GROUND)
11.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Disconnect the y1 battery voltage sensor connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the battery voltage sensor and battery cooling blower assembly (No. 0) is not loose or disconnected.




d.
A449750N01
2.135,1.198 2.521,1.438 0.385,0.24 2.156,1.219 2.49,1.417 0.333,0.198 10 true M49

Disconnect the M49 battery cooling blower assembly (No. 0) connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A449752C02
0.781,3.531 1.188,3.802 0.406,0.271 1.49,1.854 1.896,2.125 0.406,0.271 1.406,4.26 1.656,3.833 true 2.219,1.938 2.167,2.656 true 0.188,0.104 0.635,0.5 0.448,0.396 10 false *a 0.625,2.74 1.042,3.021 0.417,0.281 10 false *b 0.865,3.583 1.375,3.927 0.51,0.344 10 false M49 1.281,4.292 1.698,4.573 0.417,0.281 10 false SI0 1.625,1.917 2.135,2.26 0.51,0.344 10 false y1 2.052,2.688 2.469,2.969 0.417,0.281 10 false SI0
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 0))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-5 (SI0) - M49-3 (SI0) Ignition switch off Below 1 Ω
M49-3 (SI0) - Body ground and other terminals Ignition switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery voltage sensor and battery cooling blower assembly (No. 0) is not loose or disconnected and its terminals are not deformed or corroded.



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the ignition switch to ON.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M49-3 (SI0) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check the condition of each wire harness and each connector between the battery voltage sensor connector and battery cooling blower assembly (No. 0).



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the M49 battery cooling blower assembly (No. 0) connector.


l.

Reconnect the y1 battery voltage sensor connector.


m.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

12.CHECK BATTERY VOLTAGE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK BATTERY VOLTAGE SENSOR

b.
A449770C01
2.156,0.802 2.51,1.052 0.354,0.25 2.74,2.49 2.458,1.594 true 2.021,2.5 2.219,1.531 true 0.26,0.583 0.573,0.781 0.313,0.198 10 false *a 2.271,0.823 2.729,1.021 0.458,0.198 10 false y1 2.646,2.531 3.104,2.729 0.458,0.198 10 false GND 1.917,2.531 2.375,2.729 0.458,0.198 10 false SI0
*a Component without harness connected
(Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-5 (SI0) - y1-7 (GND) Ignition switch off 10 kΩ or higher



c.

Install the battery voltage sensor.


Result:
Proceed to
OK
NG



OK

13.CHECK BATTERY VOLTAGE SENSOR (SI0 VOLTAGE)

NG

13.CHECK BATTERY VOLTAGE SENSOR (SI0 VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


e.
A449753C06
2.115,0.229 2.552,0.458 0.438,0.229 1.969,1.76 2.229,0.969 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.24 2.656,0.552 0.396,0.313 10 false y1 1.823,1.813 2.156,2.073 0.333,0.26 10 false SI0 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
y1-5 (SI0) - y1-7 (GND) Ignition switch ON 4.5 to 5.5 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

14.CHECK BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

NG

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

14.CHECK BATTERY COOLING BLOWER ASSEMBLY (NO. 0)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly (No. 0).

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the battery voltage sensor sends a command to operate the battery cooling blower assembly (No. 0).


Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

f.
A449753C06
2.115,0.229 2.552,0.458 0.438,0.229 1.969,1.76 2.229,0.969 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.24 2.656,0.552 0.396,0.313 10 false y1 1.823,1.813 2.156,2.073 0.333,0.26 10 false SI0 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


Connect an oscilloscope to the y1 battery voltage sensor connector and check the waveform.

Item Content
Tester Connection y1-5 (SI0) - y1-7 (GND)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Ignition switch ON, during Active Test

HINT:
·

Perform this inspection with the battery voltage sensor connector connected.

·

The wave length will vary with the operating speed of the battery cooling blower assembly (No. 0).



Result:
Result Proceed to
Normal (The pulse output of waveform 1) A
No pulse generation B



g.

Turn the ignition switch off.


h.
A284431C04
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a
*a Waveform 1


Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Install the HV battery junction block assembly.



A

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

B

15.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY (NO. 0) - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.
A449750N01
2.135,1.198 2.521,1.438 0.385,0.24 2.156,1.219 2.49,1.417 0.333,0.198 10 true M49

Disconnect the M49 battery cooling blower assembly (No. 0) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A456739C04
1.51,0.229 1.906,0.521 0.396,0.292 2.125,1.76 1.833,1.333 true 0.25,0.302 0.563,0.5 0.313,0.198 10 false *a 1.583,0.302 1.99,0.604 0.406,0.302 10 false M49 1.979,1.781 2.385,2.083 0.406,0.302 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 0))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-4 (GND0) - Body ground Ignition switch off Below 1 Ω



e.

Reconnect the M49 battery cooling blower assembly (No. 0) connector.


f.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Disconnect the y1 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A449803C01
1.563,2.094 1.917,2.365 0.354,0.271 2.781,2.677 2.49,2.25 true 0.229,0.271 0.542,0.469 0.313,0.198 10 false *a 1.656,2.135 1.969,2.333 0.313,0.198 10 false y1 2.688,2.698 3.198,3.021 0.51,0.323 10 false GND
*a Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-7 (GND) - Body ground Ignition switch off Below 1 Ω



e.

Reconnect the y1 battery voltage sensor connector.


f.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATT FAN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATT FAN NO. 1 RELAY)
a.

Remove the IGCT NO. 2 fuse, BATT FAN NO. 1 relay and BATT FAN NO. 2 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A449804C01
1.865,0.188 2.177,0.385 0.313,0.198 10 false *1 0.521,0.542 0.833,0.74 0.313,0.198 10 false *2 0.5,2.229 0.813,2.427 0.313,0.198 10 false *3
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT NO. 2 Fuse Holder
*3 BATT FAN NO. 1 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT NO. 2 fuse holder) - 1 (BATT FAN NO. 1 relay holder) Ignition switch off Below 1 Ω


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Install the IGCT NO. 2 fuse, BATT FAN NO. 1 relay and BATT FAN NO. 2 relay.


Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 RELAY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 RELAY - AUXILIARY BATTERY)
a.

Remove the BATT FAN NO. 1 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A449805C01
1.615,0.188 1.927,0.385 0.313,0.198 10 false *1 0.479,1.313 0.792,1.51 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 1 Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (BATT FAN NO. 1 relay holder) - Body ground Ignition switch off 11 to 14 V


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Install the BATT FAN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 RELAY - BODY GROUND)
a.

Remove the BATT FAN NO. 1 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A449805C01
1.615,0.188 1.927,0.385 0.313,0.198 10 false *1 0.479,1.313 0.792,1.51 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 1 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BATT FAN NO. 1 relay holder) - Body ground Ignition switch off Below 1 Ω


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Install the BATT FAN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 RELAY - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 RELAY - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the BATT FAN NO. 1 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.

NOTICE:

Check the terminals of the relay for deformation and corrosion.



c.

d.
A449750N01
2.135,1.198 2.521,1.438 0.385,0.24 2.156,1.219 2.49,1.417 0.333,0.198 10 true M49

Disconnect the M49 battery cooling blower assembly (No. 0) connector.

NOTICE:
·

Check that each connector between the BATT FAN NO. 1 relay and battery cooling blower assembly (No. 0) is not loose or disconnected.

·

Before disconnecting the connector, check that it is not loose or disconnected.




e.

Measure the resistance according to the value(s) in the table below.

A449806C01
0.76,1.26 1.156,1.542 0.396,0.281 1.656,1.396 1.365,2.042 true 4.979,0.188 5.292,0.385 0.313,0.198 10 false *1 4.031,1.063 4.344,1.26 0.313,0.198 10 false *2 0.896,0.583 1.208,0.781 0.313,0.198 10 false *a 0.823,1.323 1.135,1.521 0.313,0.198 10 false M49 1.26,2.073 1.573,2.271 0.313,0.198 10 false IG0
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly *2 BATT FAN NO. 1 Relay Holder
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 0))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
5 (BATT FAN NO. 1 relay holder) - M49-1 (IG0) Ignition switch off Below 1 Ω


NOTICE:
·

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

·

Check that each connector between the BATT FAN NO. 1 relay and battery cooling blower assembly (No. 0) is not loose or disconnected.




f.

Reconnect the M49 battery cooling blower assembly (No. 0) connector.


g.

Install the rear floor silencer.


h.

Install the BATT FAN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 FUSE - BATT FAN NO. 1 RELAY)
a.

Remove the BATT FAN NO. 1 fuse and BATT FAN NO. 1 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A449807C01
1.688,0.146 2,0.344 0.313,0.198 10 false *1 0.49,0.781 0.802,0.979 0.313,0.198 10 false *2 0.49,2.208 0.802,2.406 0.313,0.198 10 false *3
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 1 Fuse Holder
*3 BATT FAN NO. 1 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BATT FAN NO. 1 fuse holder) - Terminals other than 3 (BATT FAN NO. 1 relay holder) and body ground Ignition switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Install the BATT FAN NO. 1 fuse and BATT FAN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 RELAY - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

NG

24.REPAIR OR REPLACE HARNESS OR CONNECTOR
22.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 1 RELAY - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the BATT FAN NO. 1 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


c.

d.
A449750N01
2.135,1.198 2.521,1.438 0.385,0.24 2.156,1.219 2.49,1.417 0.333,0.198 10 true M49

Disconnect the M49 battery cooling blower assembly (No. 0) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.

Measure the resistance according to the value(s) in the table below.

A449806C01
0.76,1.26 1.156,1.542 0.396,0.281 1.656,1.396 1.365,2.042 true 4.979,0.188 5.292,0.385 0.313,0.198 10 false *1 4.031,1.063 4.344,1.26 0.313,0.198 10 false *2 0.896,0.583 1.208,0.781 0.313,0.198 10 false *a 0.823,1.323 1.135,1.521 0.313,0.198 10 false M49 1.26,2.073 1.573,2.271 0.313,0.198 10 false IG0
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly *2 BATT FAN NO. 1 Relay Holder
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 0))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
5 (BATT FAN NO. 1 relay holder) - M49-1 (IG0) Ignition switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



f.

Reconnect the M49 battery cooling blower assembly (No. 0) connector.


g.

Install the rear floor silencer.


h.

Install the BATT FAN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

23.CHECK BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
23.CHECK BATTERY COOLING BLOWER ASSEMBLY (NO. 0)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.
A449750N01
2.135,1.198 2.521,1.438 0.385,0.24 2.156,1.219 2.49,1.417 0.333,0.198 10 true M49

Disconnect the M49 battery cooling blower assembly (No. 0) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A456740C01
1.448,0.156 1.833,0.458 0.385,0.302 1.792,1.198 2.104,1.823 true 1.302,1.813 1.51,1.427 true 0.208,0.115 0.781,0.625 0.573,0.51 10 false *a 1.531,0.24 2.104,0.75 0.573,0.51 10 false M49 2.063,1.844 2.552,2.177 0.49,0.333 10 false IG0 1.104,1.854 1.615,2.125 0.51,0.271 10 false GND0
*a Component without harness connected
(Battery Cooling Blower Assembly (No. 0))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-1 (IG0) - M49-4 (GND0) and Body ground Ignition switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



e.

Reconnect the M49 battery cooling blower assembly (No. 0) connector.


f.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (BATT FAN NO. 1)

NG

26.REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 0)
24.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN NO. 1)

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN NO. 1)

26.REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

NEXT

REPLACE FUSE (BATT FAN NO. 1)

27.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID BATTERY COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

c.

Select fan mode 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly (No. 1).

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check if the fan operates and air is sucked in. In accordance with fail-safe system operation, the battery voltage sensor sends a command to operate the battery cooling blower assembly (No. 1).


Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

d.

Check that the battery cooling blower assembly (No. 1) operates, air is sucked into the inlet duct and the operation sound is normal.

HINT:

The battery cooling blower assembly (No. 1) may not stop even when turning the cooling fan off in the "Control the Hybrid Battery Cooling Fan" Active Test. This is due to HV system control and is not a malfunction.


OK:

The battery cooling blower assembly (No. 1) operates.



e.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

NG

32.CHECK FUSE (BATT FAN NO. 2)
28.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Disconnect the y1 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A449751N01
1.594,1.688 1.979,1.927 0.385,0.24 1.635,1.719 1.969,1.896 0.333,0.177 10 true M50

Disconnect the M50 battery cooling blower assembly (No. 1) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A449752C03
1.396,1.802 1.854,2.073 0.458,0.271 0.833,3.542 1.292,3.813 0.458,0.271 1.854,3.646 2.167,4.25 true 1.823,2.573 2.135,2.01 true 0.135,0.115 0.594,0.604 0.458,0.49 10 false *a 0.24,3.021 0.604,3.323 0.365,0.302 10 false *b 0.927,3.604 1.448,3.906 0.521,0.302 10 false M50 1.563,1.844 2.083,2.146 0.521,0.302 10 false y1 2.073,4.271 2.438,4.573 0.365,0.302 10 false FP1 1.688,2.594 2.052,2.896 0.365,0.302 10 false FP1
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 1))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-12 (FP1) - M50-2 (FP1) Ignition switch off Below 1 Ω
y1-12 (FP1) - Body ground and other terminals Ignition switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the ignition switch to ON.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
y1-12 (FP1) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check the condition of each wire harness and each connector between the battery voltage sensor connector and battery cooling blower assembly (No. 1).



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the M50 battery cooling blower assembly (No. 1) connector.


l.

Reconnect the y1 battery voltage sensor connector.


m.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

29.READ VALUE USING GTS (HYBRID/EV BATTERY COOLING FAN 2 FREQUENCY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.READ VALUE USING GTS (HYBRID/EV BATTERY COOLING FAN 2 FREQUENCY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly (No. 1).

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the battery voltage sensor sends a command to operate the battery cooling fan assembly (No. 1).


Powertrain > Hybrid Control > Active Test
Active Test Display
Control the Hybrid Battery Cooling Fan
Data List Display
Hybrid/EV Battery Cooling Fan 2 Frequency
50004 397 2 659

f.
A449753C08
2.115,0.229 2.552,0.458 0.438,0.229 1.927,1.781 2.167,1.021 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.25 2.656,0.563 0.396,0.313 10 false y1 1.792,1.813 2.125,2.073 0.333,0.26 10 false FP1 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


While the battery cooling blower assembly (No. 1) is operating, compare the value in the Data List (Hybrid/EV Battery Cooling Fan 2 Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.

Specified Condition:
Tester Connection Condition
y1-12 (FP1) - y1-7 (GND) Battery cooling blower assembly (No. 1) is operating.


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.



Result:
Result Proceed to
Both of the values in the Data List (Hybrid/EV Battery Cooling Fan 2 Frequency) and the actual measured value at the battery voltage sensor connector are 0 Hz. A
Other than above B


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Install the HV battery junction block assembly.



A

30.CHECK BATTERY VOLTAGE SENSOR

B

31.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
30.CHECK BATTERY VOLTAGE SENSOR
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.
A449751N01
1.594,1.688 1.979,1.927 0.385,0.24 1.635,1.719 1.969,1.896 0.333,0.177 10 true M50

Disconnect the M50 battery cooling blower assembly (No. 1) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.
A456739C05
1.51,0.25 1.948,0.531 0.438,0.281 2.354,1.427 1.833,1.135 true 2.188,1.74 1.823,1.354 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.604,0.323 2.26,0.844 0.656,0.521 10 false M50 2.406,1.396 2.99,2.021 0.583,0.625 10 false FP1 2.115,1.771 2.667,2.083 0.552,0.313 10 false GND1
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 1))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M50-2 (FP1) - M50-4 (GND1) Ignition switch ON 4.5 to 5.5 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the M50 battery cooling blower assembly (No. 1) connector.


j.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

NG

31.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly (No. 1).

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the battery voltage sensor sends a command to operate the battery cooling blower assembly (No. 1).


Powertrain > Hybrid Control > Active Test
Active Test Display
Control the Hybrid Battery Cooling Fan
Data List Display
Hybrid/EV Battery Cooling Fan 2 Frequency
50004 397 2 659

f.
A449753C08
2.115,0.229 2.552,0.458 0.438,0.229 1.927,1.781 2.167,1.021 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.25 2.656,0.563 0.396,0.313 10 false y1 1.792,1.813 2.125,2.073 0.333,0.26 10 false FP1 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


While the battery cooling blower assembly (No. 1) is operating, compare the value in the Data List (Hybrid/EV Battery Cooling Fan 2 Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.

Specified Condition:
Tester Connection Condition Specified Condition
y1-12 (FP1) - y1-7 (GND) Battery cooling blower assembly (No. 1) is operating. Difference between the value in the Data List (Hybrid/EV Battery Cooling Fan 2 Frequency) and the actual measured value at the battery voltage sensor connector is 10% or less.


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

NG

32.CHECK FUSE (BATT FAN NO. 2)
a.
A449808C01
2.365,1.042 2.813,1.25 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *1 2.854,1.198 3.167,1.396 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 2 Fuse


Remove the BATT FAN NO. 2 fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance of the BATT FAN NO. 2 fuse.

Standard Resistance:
Tester Connection Condition Specified Condition
BATT FAN NO. 2 fuse Ignition switch off Below 1 Ω



c.

Install the BATT FAN NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

33.CHECK RELAY (BATT FAN NO. 2)

NG

45.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 FUSE - BATT FAN NO. 2 RELAY)
33.CHECK RELAY (BATT FAN NO. 2)
a.
A449809C01
0.667,2.99 1.25,2.677 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *1 0.479,2.906 0.792,3.104 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 2 Relay


Remove the BATT FAN NO. 2 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
B060778N68
2.51,1.625 2.844,1.625 true 2.521,1.125 2.854,1.125 true 2.615,0.583 2.792,0.271 2.792,0.271 2.948,0.271 true 2.021,0.573 1.865,0.26 1.865,0.26 1.719,0.26 true 2.896,1.552 3.406,2.167 0.51,0.615 10 true 3 2.906,1.042 3.104,1.24 0.198,0.198 10 false 5 3.01,0.177 3.208,0.375 0.198,0.198 10 false 2 1.573,0.177 1.771,0.375 0.198,0.198 10 false 1 1.219,0.76 1.417,0.958 0.198,0.198 10 false 5 1.229,1.302 1.427,1.5 0.198,0.198 10 false 2 0.208,0.76 0.417,0.927 0.208,0.167 10 false 3 0.219,1.302 0.417,1.5 0.198,0.198 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the BATT FAN NO. 2 relay.


Result:
Proceed to
OK
NG



OK

34.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 FUSE - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

NG

REPLACE RELAY (BATT FAN NO. 2)

34.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 FUSE - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.
A449751N01
1.594,1.688 1.979,1.927 0.385,0.24 1.635,1.719 1.969,1.896 0.333,0.177 10 true M50

Disconnect the M50 battery cooling blower assembly (No. 1) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

f.
A456739C06
1.51,0.292 1.948,0.573 0.438,0.281 2.219,1.792 1.865,1.344 true 1.604,1.146 1.271,1.792 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.615,0.365 2.271,0.885 0.656,0.521 10 false M50 1.135,1.823 1.74,2.177 0.604,0.354 10 false IG1 2.115,1.823 2.75,2.115 0.635,0.292 10 false GND1
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 1))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M50-1 (IG1) - M50-4 (GND1) Ignition switch ON 11 to 14 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)

·

Fuse condition (before and after removing fuse(s)) (IG circuit)

·

Connection condition of connectors (IG circuit)

·

Wire harness condition (IG circuit)

·

Wire harness condition (GND circuit)




g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the M50 battery cooling blower assembly (No. 1) connector.


j.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

35.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

NG

39.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY (NO. 1) - BODY GROUND)
35.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Disconnect the y1 battery voltage sensor connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the battery voltage sensor and battery cooling blower assembly (No. 1) is not loose or disconnected.




d.
A449751N01
1.594,1.688 1.979,1.927 0.385,0.24 1.635,1.719 1.969,1.896 0.333,0.177 10 true M50

Disconnect the M50 battery cooling blower assembly (No. 1) connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A449752C04
0.771,3.552 1.177,3.823 0.406,0.271 1.49,1.854 1.896,2.125 0.406,0.271 1.458,4.271 1.656,3.823 true 2.135,1.938 2.083,2.656 true 0.188,0.104 0.635,0.5 0.448,0.396 10 false *a 0.625,2.74 1.042,3.021 0.417,0.281 10 false *b 0.844,3.625 1.354,3.969 0.51,0.344 10 false M50 1.344,4.292 1.76,4.573 0.417,0.281 10 false SI1 1.625,1.896 2.135,2.24 0.51,0.344 10 false y1 1.969,2.688 2.385,2.969 0.417,0.281 10 false SI1
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 1))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-6 (SI1) - M50-3 (SI1) Ignition switch off Below 1 Ω
M50-3 (SI1) - Body ground and other terminals Ignition switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery voltage sensor and battery cooling blower assembly (No. 1) is not loose or disconnected and its terminals are not deformed or corroded.



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the ignition switch to ON.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M50-3 (SI1) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check the condition of each wire harness and each connector between the battery voltage sensor connector and battery cooling blower assembly (No. 1).



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the M50 battery cooling blower assembly (No. 1) connector.


l.

Reconnect the y1 battery voltage sensor connector.


m.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

36.CHECK BATTERY VOLTAGE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK BATTERY VOLTAGE SENSOR

b.
A449770C05
2.156,0.802 2.51,1.052 0.354,0.25 2.74,2.49 2.458,1.594 true 1.958,2.5 2.156,1.531 true 0.26,0.583 0.573,0.781 0.313,0.198 10 false *a 2.271,0.823 2.729,1.021 0.458,0.198 10 false y1 2.646,2.531 3.104,2.729 0.458,0.198 10 false GND 1.802,2.531 2.26,2.729 0.458,0.198 10 false SI1
*a Component without harness connected
(Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-6 (SI1) - y1-7 (GND) Ignition switch off 10 kΩ or higher



c.

Install the battery voltage sensor.


Result:
Proceed to
OK
NG



OK

37.CHECK BATTERY VOLTAGE SENSOR (SI1 VOLTAGE)

NG

37.CHECK BATTERY VOLTAGE SENSOR (SI1 VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


e.
A449753C09
2.115,0.229 2.552,0.458 0.438,0.229 1.906,1.76 2.167,0.969 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.24 2.656,0.552 0.396,0.313 10 false y1 1.75,1.813 2.083,2.073 0.333,0.26 10 false SI1 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
y1-6 (SI1) - y1-7 (GND) Ignition switch ON 4.5 to 5.5 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

38.CHECK BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

NG

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

38.CHECK BATTERY COOLING BLOWER ASSEMBLY (NO. 1)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly (No. 1).

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the battery voltage sensor sends a command to operate the battery cooling blower assembly (No. 1).


Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

f.
A449753C09
2.115,0.229 2.552,0.458 0.438,0.229 1.906,1.76 2.167,0.969 true 2.74,1.792 2.49,1.031 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.24 2.656,0.552 0.396,0.313 10 false y1 1.75,1.813 2.083,2.073 0.333,0.26 10 false SI1 2.625,1.813 2.958,2.073 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


Connect an oscilloscope to the y1 battery voltage sensor connector and check the waveform.

Item Content
Tester Connection y1-6 (SI1) - y1-7 (GND)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Ignition switch ON, during Active Test

HINT:
·

Perform this inspection with the battery voltage sensor connector connected.

·

The wave length will vary with the operating speed of the battery cooling blower assembly (No. 1).



Result:
Result Proceed to
Normal (The pulse output of waveform 1) A
No pulse generation B



g.

Turn the ignition switch off.


h.
A284431C04
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a
*a Waveform 1


Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Install the HV battery junction block assembly.



A

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

B

39.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY (NO. 1) - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.
A449751N01
1.594,1.688 1.979,1.927 0.385,0.24 1.635,1.719 1.969,1.896 0.333,0.177 10 true M50

Disconnect the M50 battery cooling blower assembly (No. 1) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A456739C07
1.51,0.271 1.948,0.552 0.438,0.281 2.052,1.74 1.844,1.344 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.615,0.354 2.271,0.875 0.656,0.521 10 false M50 1.927,1.771 2.563,2.156 0.635,0.385 10 false GND1
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 1))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M50-4 (GND1) - Body ground Ignition switch off Below 1 Ω



e.

Reconnect the M50 battery cooling blower assembly (No. 1) connector.


f.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

40.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Disconnect the y1 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A449803C01
1.563,2.094 1.917,2.365 0.354,0.271 2.781,2.677 2.49,2.25 true 0.229,0.271 0.542,0.469 0.313,0.198 10 false *a 1.656,2.135 1.969,2.333 0.313,0.198 10 false y1 2.688,2.698 3.198,3.021 0.51,0.323 10 false GND
*a Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-7 (GND) - Body ground Ignition switch off Below 1 Ω



e.

Reconnect the y1 battery voltage sensor connector.


f.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

41.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATT FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATT FAN NO. 2 RELAY)
a.

Remove the IGCT NO. 2 fuse, BATT FAN NO. 1 relay and BATT FAN NO. 2 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A449810C01
1.865,0.188 2.177,0.385 0.313,0.198 10 false *1 0.521,0.542 0.833,0.74 0.313,0.198 10 false *2 0.5,2.146 0.813,2.344 0.313,0.198 10 false *3
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT NO. 2 Fuse Holder
*3 BATT FAN NO. 2 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT NO. 2 fuse holder) - 1 (BATT FAN NO. 2 relay holder) Ignition switch off Below 1 Ω


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Install the IGCT NO. 2 fuse, BATT FAN NO. 1 relay and BATT FAN NO. 2 relay.


Result:
Proceed to
OK
NG



OK

42.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 RELAY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 RELAY - AUXILIARY BATTERY)
a.

Remove the BATT FAN NO. 2 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A449811C01
1.615,0.188 1.927,0.385 0.313,0.198 10 false *1 0.448,1.865 0.76,2.063 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 2 Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (BATT FAN NO. 2 relay holder) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Install the BATT FAN NO. 2 relay.


Result:
Proceed to
OK
NG



OK

43.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

43.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 RELAY - BODY GROUND)
a.

Remove the BATT FAN NO. 2 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A449811C01
1.615,0.188 1.927,0.385 0.313,0.198 10 false *1 0.448,1.865 0.76,2.063 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 2 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BATT FAN NO. 2 relay holder) - Body ground Ignition switch off Below 1 Ω


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Install the BATT FAN NO. 2 relay.


Result:
Proceed to
OK
NG



OK

44.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 RELAY - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 RELAY - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the BATT FAN NO. 2 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.

NOTICE:

Check the terminals of the relay for deformation and corrosion.



c.

d.
A449751N01
1.594,1.688 1.979,1.927 0.385,0.24 1.635,1.719 1.969,1.896 0.333,0.177 10 true M50

Disconnect the M50 battery cooling blower assembly (No. 1) connector.

NOTICE:
·

Check that each connector between the BATT FAN NO. 2 relay and battery cooling blower assembly (No. 1) is not loose or disconnected.

·

Before disconnecting the connector, check that it is not loose or disconnected.




e.

Measure the resistance according to the value(s) in the table below.

A456733C01
0.76,1.26 1.156,1.542 0.396,0.281 1.781,1.438 1.594,2.219 true 4.708,0.188 5.021,0.385 0.313,0.198 10 false *1 3.823,1.51 4.135,1.708 0.313,0.198 10 false *2 0.896,0.583 1.208,0.781 0.313,0.198 10 false *a 0.823,1.323 1.135,1.521 0.313,0.198 10 false M50 1.469,2.26 1.781,2.458 0.313,0.198 10 false IG1
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly *2 BATT FAN NO. 2 Relay Holder
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 1))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
5 (BATT FAN NO. 2 relay holder) - M50-1 (IG1) Ignition switch off Below 1 Ω


NOTICE:
·

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

·

Check that each connector between the BATT FAN NO. 2 relay and battery cooling blower assembly (No. 1) is not loose or disconnected.




f.

Reconnect the M50 battery cooling blower assembly (No. 1) connector.


g.

Install the rear floor silencer.


h.

Install the BATT FAN NO. 2 relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 FUSE - BATT FAN NO. 2 RELAY)
a.

Remove the BATT FAN NO. 2 fuse and BATT FAN NO. 2 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A456734C01
1.688,0.146 2,0.344 0.313,0.198 10 false *1 0.438,0.604 0.75,0.802 0.313,0.198 10 false *2 0.406,1.875 0.719,2.073 0.313,0.198 10 false *3
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 BATT FAN NO. 2 Fuse Holder
*3 BATT FAN NO. 2 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BATT FAN NO. 2 fuse holder) - Terminals other than 3 (BATT FAN NO. 2 relay holder) and body ground Ignition switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Install the BATT FAN NO. 2 fuse and BATT FAN NO. 2 relay.


Result:
Proceed to
OK
NG



OK

46.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 RELAY - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

NG

48.REPAIR OR REPLACE HARNESS OR CONNECTOR
46.CHECK HARNESS AND CONNECTOR (BATT FAN NO. 2 RELAY - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the BATT FAN NO. 2 relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


c.

d.
A449751N01
1.594,1.688 1.979,1.927 0.385,0.24 1.635,1.719 1.969,1.896 0.333,0.177 10 true M50

Disconnect the M50 battery cooling blower assembly (No. 1) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.

Measure the resistance according to the value(s) in the table below.

A456733C01
0.76,1.26 1.156,1.542 0.396,0.281 1.781,1.438 1.594,2.219 true 4.708,0.188 5.021,0.385 0.313,0.198 10 false *1 3.823,1.51 4.135,1.708 0.313,0.198 10 false *2 0.896,0.583 1.208,0.781 0.313,0.198 10 false *a 0.823,1.323 1.135,1.521 0.313,0.198 10 false M50 1.469,2.26 1.781,2.458 0.313,0.198 10 false IG1
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly *2 BATT FAN NO. 2 Relay Holder
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly (No. 1))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
5 (BATT FAN NO. 2 relay holder) - M50-1 (IG1) Ignition switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



f.

Reconnect the M50 battery cooling blower assembly (No. 1) connector.


g.

Install the rear floor silencer.


h.

Install the BATT FAN NO. 2 relay.


Result:
Proceed to
OK
NG



OK

47.CHECK BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

NG

49.REPAIR OR REPLACE HARNESS OR CONNECTOR
47.CHECK BATTERY COOLING BLOWER ASSEMBLY (NO. 1)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.
A449751N01
1.594,1.688 1.979,1.927 0.385,0.24 1.635,1.719 1.969,1.896 0.333,0.177 10 true M50

Disconnect the M50 battery cooling blower assembly (No. 1) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A456740C02
1.458,0.177 1.844,0.479 0.385,0.302 1.781,1.177 2.104,1.833 true 1.167,1.844 1.49,1.375 true 0.208,0.115 0.781,0.625 0.573,0.51 10 false *a 1.521,0.26 2.094,0.771 0.573,0.51 10 false M50 2.063,1.854 2.531,2.073 0.469,0.219 10 false IG1 0.948,1.865 1.458,2.135 0.51,0.271 10 false GND1
*a Component without harness connected
(Battery Cooling Blower Assembly (No. 1))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M50-1 (IG1) - M50-4 (GND1) and Body ground Ignition switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



e.

Reconnect the M50 battery cooling blower assembly (No. 1) connector.


f.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (BATT FAN NO. 2)

NG

50.REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 1)
48.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN NO. 2)

49.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN NO. 2)

50.REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

NEXT

REPLACE FUSE (BATT FAN NO. 2)