Refer to the description for DTC P0A9B11.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>P0A9B11
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A9B2A | Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range | The performance of battery temperature sensor 0 is abnormal and its output is stuck.
(2 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0AC52A | Hybrid/EV Battery Temperature Sensor "B" Signal Stuck In Range | The performance of battery temperature sensor 1 is abnormal and its output is stuck.
(2 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0ACA2A | Hybrid/EV Battery Temperature Sensor "C" Signal Stuck In Range | The performance of battery temperature sensor 2 is abnormal and its output is stuck.
(2 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0AE82A | Hybrid/EV Battery Temperature Sensor "D" Signal Stuck In Range | The performance of battery temperature sensor 3 is abnormal and its output is stuck.
(2 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0BC22A | Hybrid/EV Battery Temperature Sensor "E" Signal Stuck In Range | The performance of battery temperature sensor 4 is abnormal and its output is stuck.
(2 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0C332A | Hybrid/EV Battery Temperature Sensor "F" Signal Stuck In Range | The performance of battery temperature sensor 5 is abnormal and its output is stuck.
(2 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P306562 | Hybrid/EV Battery Temperature Sensor "Group 1" Signal Compare Failure | The performance of any battery temperature sensor (0 to 2) is abnormal, and the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P306A62 | Hybrid/EV Battery Temperature Sensor "Group 2" Signal Compare Failure | The performance of any battery temperature sensor (3 to 5) is abnormal, and the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P0A9B2A | Hybrid Battery Temperature 1 to 6 |
| P0AC52A | |
| P0ACA2A | |
| P0AE82A | |
| P0BC22A | |
| P0C332A | |
| P306562 | |
| P306A62 |
If the vehicle is left as is for 24 hours, the value of "Hybrid Battery Temperature" will be almost the same as the ambient temperature.
The following items can be helpful when performing repairs:
Vehicle Speed
Ambient Temperature
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY
P0A9B2A, P0AC52A, P0ACA2A, P0AE82A, P0BC22A, P0C332A:
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Drive the vehicle for approximately 10 minutes according to the Freeze Frame Data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Temperature 1 to 6" and "Hybrid Battery Current" when ambient temperature is -10°C (14°F) or higher. (These DTCs may not be stored if the vehicle is stopped or being driven at a steady speed.)
Check that the output of each battery temperature sensor varies.
Check that the difference in output between each battery temperature sensor is not excessively large.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
P306562, P306A62:
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
With ignition switch ON and wait for 10 seconds or more when the ambient temperature is -10°C (14°F) or higher.
Check that the difference in output between each battery temperature sensor is not excessively large.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0AFC00 or P0AFC96 is not output. | A |
| P0AFC00 or P0AFC96 is also output. | B |
Turn the ignition switch off.
A
B
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the upper HV battery cover sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY THERMISTOR>REMOVAL
Visually check the installation condition of the relevant battery temperature sensor.
| *1 | Battery Temperature Sensor 0 | *2 | Battery Temperature Sensor 1 |
| *3 | Battery Temperature Sensor 2 | *4 | Battery Temperature Sensor 3 |
| *5 | Battery Temperature Sensor 4 | *6 | Battery Temperature Sensor 5 |
Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely.
| Result | Proceed to |
|---|---|
| Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely. | A |
| Claws are damaged. | B |
| Any of battery temperature sensors are not installed correctly, but claws are not damaged. | C |
Install the upper HV battery cover sub-assembly.
A
B
C
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery junction block assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL
Disconnect the z12 battery voltage sensor connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Battery Voltage Sensor) |
Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 5).
| Tester Connection | Battery Temperature Sensor |
|---|---|
| z12-7 (TB0) - z12-19 (GB0) | 0 |
| z12-6 (TB1) - z12-18 (GB1) | 1 |
| z12-5 (TB2) - z12-17 (GB2) | 2 |
| z12-4 (TB3) - z12-16 (GB3) | 3 |
| z12-3 (TB4) - z12-15 (GB4) | 4 |
| z12-2 (TB5) - z12-14 (GB5) | 5 |
| Thermistor Temperature | Condition | Specified Condition |
|---|---|---|
| 0 to 10°C (32 to 50°F) | Ignition switch off | 17.7 to 27.8 kΩ |
| 10 to 20°C (50 to 68°F) | Ignition switch off | 12.0 to 18.2 kΩ |
| 20 to 30°C (68 to 86°F) | Ignition switch off | 8.22 to 12.2 kΩ |
| 30 to 40°C (86 to 104°F) | Ignition switch off | 5.74 to 8.41 kΩ |
| 40 to 50°C (104 to 122°F) | Ignition switch off | 4.09 to 5.91 kΩ |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Disconnect the y1 battery voltage sensor connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Battery Voltage Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z12-7 (TB0) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-7 (TB0) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-19 (GB0) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-19 (GB0) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-6 (TB1) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-6 (TB1) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-18 (GB1) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-18 (GB1) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-5 (TB2) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-5 (TB2) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-17 (GB2) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-17 (GB2) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-4 (TB3) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-4 (TB3) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-16 (GB3) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-16 (GB3) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-3 (TB4) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-3 (TB4) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-15 (GB4) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-15 (GB4) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-2 (TB5) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-2 (TB5) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-14 (GB5) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-14 (GB5) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-1 (TC0) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-1 (TC0) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
| z12-13 (GC0) - y1-1 (IGCT) | Ignition switch off | 10 kΩ or higher |
| z12-13 (GC0) - y1-7 (GND) | Ignition switch off | 10 kΩ or higher |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the y1 and z12 battery voltage sensor connectors.
Install the HV battery junction block assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the upper HV battery cover sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY THERMISTOR>REMOVAL
Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.
There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.
Install the upper HV battery cover sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG