Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P260071  Motor/Generator Coolant Pump "A" Actuator Stuck  P2B8600  Coolant Pump "A" Overspeed/Air in System  


DESCRIPTION

Refer to the description for DTC P260031.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>P260031

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P260071 Motor/Generator Coolant Pump "A" Actuator Stuck When the oil pump startup request signal is output and the oil pump operation has failed a certain number of times or more, after soaking for a certain amount of time, oil pump operation is confirmed to of failed.
(2 trip detection logic)
·

Oil pipe

·

Oil pump with motor assembly

·

Hybrid vehicle control ECU

·

Wire harness or connector

·

OIL PMP relay

·

OIL PMP fuse


Does not come on Master Warning:
Comes on
P2B8600 Coolant Pump "A" Overspeed/Air in System When the oil pump startup request signal is output, overspeed is detected a certain number of times or more.
(2 trip detection logic)
·

Oil pipe

·

Oil pump with motor assembly

·

Hybrid vehicle control ECU

·

Wire harness or connector

·

OIL PMP relay

·

OIL PMP fuse


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P260071
·

Target Motor/Generator Cooling Oil Pump Motor Duty

·

Motor/Generator Cooling Oil Pump Motor Revolution

·

Motor/Generator Cooling Oil Pump Motor Power Relay Request


P2B8600

HINT:

The oil pump with motor assembly cannot be activated only with the OIL PMP relay on. It is activated after receiving the command signals (OPM1) from the hybrid vehicle control ECU.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Motor/Generator Cooling Oil Pump.

6.

According to the display on the GTS, perform the Active Test and set the duty to 90%.

HINT:

The Active Test cannot be performed if the duty ratio is set to 50% or lower or 95% or higher, or if the ambient temperature is 0°C (30°F) or lower.


7.

According to the display on the GTS, read the Data List and check that the value of "Motor/Generator Cooling Oil Pump Motor Revolution" is between 160 rpm and 7600 rpm.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTC P260071 or P2B8600 only is output, or DTCs except the ones in the tables below are also output. A
DTC P260071 or P2B8600 and any of the DTCs in the following table are output at the same time. B


Relevant DTC
P274A11 Transmission Fluid Temperature Sensor "C" Circuit Short to Ground
P274A15 Transmission Fluid Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open
P274A1C Transmission Fluid Temperature Sensor "C" Voltage Out of Range
P274A1F Transmission Fluid Temperature Sensor "C" Circuit Intermittent

HINT:

The transmission fluid temperature sensor value is used to detect DTC P260071 and P2B8600. Check that the transmission fluid temperature sensor operates normally, as the detection condition for DTC P260071 or P2B8600 may be mistakenly detected due to a malfunction in the transmission fluid temperature sensor.



b.

Turn the ignition switch off.



A

2.CHECK OIL PIPE

B

2.CHECK OIL PIPE
a.

Check that there is no clogging in the oil pipes connected to the oil pump with motor assembly, oil cooler assembly and hybrid vehicle transaxle assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (OIL PUMP WITH MOTOR ASSEMBLY CONNECTOR)

NG

REPAIR OR REPLACE OIL PIPE

3.CHECK CONNECTOR CONNECTION CONDITION (OIL PUMP WITH MOTOR ASSEMBLY CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)

OK

6.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - BODY GROUND)

NG

11.CHECK FUSE (OIL PMP)
6.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - BODY GROUND)

OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

OK

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE MOTOR/GENERATOR COOLING OIL PUMP MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE MOTOR/GENERATOR COOLING OIL PUMP MOTOR)
a.

Set the Duty ratio to 90%.

HINT:

The active test is not performed when the Duty ratio is 50% or lower or 95% or higher, or the ambient temperature is 0°C (30°F) or lower.


Powertrain > Hybrid Control > Active Test
Tester Display
Control the Motor/Generator Cooling Oil Pump
50004 397 42002

b.

Confirm that the oil pump with motor assembly is operating.

OK:

The oil pump with motor assembly is operating.



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

10.INSPECT OIL PUMP WITH MOTOR ASSEMBLY

NG

13.INSPECT OIL PUMP WITH MOTOR ASSEMBLY
10.INSPECT OIL PUMP WITH MOTOR ASSEMBLY
a.

Remove the oil pump with motor assembly.

Click hereDrivetrain>P810 (HYBRID TRANSMISSION / TRANSAXLE)>OIL PUMP>REMOVAL


b.
A449794C01
1.438,0.177 1.844,0.448 0.406,0.271 0.865,1.813 1.104,1.115 true 1.854,1.813 1.604,1.115 true 0.063,0.073 0.302,0.302 0.24,0.229 10 false *a 0.813,1.844 1,2.052 0.188,0.208 10 false L 1.708,1.844 2.323,2.042 0.615,0.198 10 false OPM1 1.521,0.229 1.979,0.427 0.458,0.198 10 false C38
*a Component without harness connected
(Oil Pump with Motor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Condition Specified Condition
C38-3 (OPM1) (+) - C38-4 (L) (-) Ignition switch off 10 kΩ or higher


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.



c.

Install the oil pump with motor assembly.


Result:
Proceed to
OK
NG



OK

NG

REPLACE OIL PUMP WITH MOTOR ASSEMBLY

11.CHECK FUSE (OIL PMP)

OK

12.INSPECT RELAY (OIL PMP)

NG

REPLACE FUSE (OIL PMP)

12.INSPECT RELAY (OIL PMP)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPLACE RELAY (OIL PMP)

13.INSPECT OIL PUMP WITH MOTOR ASSEMBLY
a.

Remove the oil pump with motor assembly.

Click hereDrivetrain>P810 (HYBRID TRANSMISSION / TRANSAXLE)>OIL PUMP>REMOVAL


b.

Set the Toyota Electrical Tester to diode check mode.


c.
A449794C01
1.438,0.177 1.844,0.448 0.406,0.271 0.865,1.813 1.104,1.115 true 1.854,1.813 1.604,1.115 true 0.063,0.073 0.302,0.302 0.24,0.229 10 false *a 0.813,1.844 1,2.052 0.188,0.208 10 false L 1.708,1.844 2.323,2.042 0.615,0.198 10 false OPM1 1.521,0.229 1.979,0.427 0.458,0.198 10 false C38
*a Component without harness connected
(Oil Pump with Motor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
(Tester Probe Polarity)
Condition Specified Condition
C38-3 (OPM1) (-) - C38-4 (L) (+) Ignition switch off 1.5 V or higher


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.



d.

Install the oil pump with motor assembly.


Result:
Proceed to
OK
NG



OK

14.INSPECT HYBRID VEHICLE CONTROL ECU

NG

REPLACE OIL PUMP WITH MOTOR ASSEMBLY

14.INSPECT HYBRID VEHICLE CONTROL ECU
a.

Set the Duty ratio to 90%.

HINT:

The active test is not performed when the Duty ratio is 50% or lower or 95% or higher, or the ambient temperature is 0°C (30°F) or lower.


Powertrain > Hybrid Control > Active Test
Tester Display
Control the Motor/Generator Cooling Oil Pump
50004 397 42002

b.

Connect an oscilloscope to the C38 oil pump with motor assembly connector and check the waveform.

A456754C06
1.49,0.229 1.896,0.5 0.406,0.271 5.26,0.219 5.667,0.49 0.406,0.271 0.802,2.375 1.094,1.24 true 6.323,2.281 5.958,1.156 true 1.563,0.281 2.021,0.479 0.458,0.198 10 false A31 5.354,0.281 5.813,0.479 0.458,0.198 10 false H67 0.583,2.417 1.135,2.667 0.552,0.25 10 false OPM1 6.292,2.323 6.844,2.573 0.552,0.25 10 false E1 4.615,2.854 5.156,3.104 0.542,0.25 10 false GND 0.198,0.115 0.75,0.365 0.552,0.25 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Content
Tester Connection A31-21 (OPM1) - H67-3 (E1)
Equipment Setting 10 V/DIV., 20 ms./DIV.
Condition Ignition switch ON
During Active Test

Result:
Result Proceed to
11 to 14 V A
Except above B



c.

Turn the ignition switch off.



A

B

REPLACE OIL PUMP WITH MOTOR ASSEMBLY