Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420995 MOTOR GENERATOR CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for 2WD)  P31241F  Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent  P312487  Lost Communication between Drive Motor "A" and HV ECU Missing Message  


DESCRIPTION

The motor generator control ECU, which is built into the inverter with converter assembly, controls the motor (MG2) based on commands from the hybrid vehicle control ECU.

The motor generator control ECU (MG ECU) monitors communication data and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P31241F Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard) detected when DTC P0C7917, P0D3319, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Does not come on
P312487 Lost Communication between Drive Motor "A" and HV ECU Missing Message Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle control ECU


Comes on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the Inverter Low-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>Inverter Low-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Motor Generator > Clear DTCs
50002 395

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DIAGNOSIS RELATED INFORMATION AND DTC OUTPUT (MOTOR GENERATOR)
2.CHECK DIAGNOSIS RELATED INFORMATION AND DTC OUTPUT (MOTOR GENERATOR)
a.

Turn the ignition switch to ON and wait for 2 minutes or more.


b.

Read the diagnosis related information and check for DTCs.

Powertrain > Motor Generator > Utility
Tester Display
Diagnosis Related Information
50005 395 1056
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P31241F or P312487 is listed in Diagnosis Related Information or P31241F or P312487 is output. A
P31241F and P312487 are not listed in Diagnosis Information and P31241F and P312487 are not output. B



c.

Turn the ignition switch off.



A

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

B

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table.


b.

Turn the ignition switch to ON.


c.

Measure the waveform.

C408931C06
1.51,0.094 1.938,0.385 0.427,0.292 5.229,0.094 5.656,0.385 0.427,0.292 2.354,2 2.052,1.021 true 6.323,2.042 6.042,1.042 true 1.667,2 1.938,1.146 true 2.417,2.406 2.875,2.604 0.458,0.198 10 false CH1 2.438,3.021 2.896,3.219 0.458,0.198 10 false CH2 4.635,2.844 5.094,3.042 0.458,0.198 10 false GND 4.635,3.313 5.094,3.51 0.458,0.198 10 false GND 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 5.313,0.167 5.771,0.365 0.458,0.198 10 false H67 1.594,0.167 2.052,0.365 0.458,0.198 10 false A31 2.188,2.042 2.802,2.24 0.615,0.198 10 false HMCH 1.479,2.042 2.094,2.24 0.615,0.198 10 false HMCL 6.271,2.104 6.885,2.302 0.615,0.198 10 false E1
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Contents
Tester Connection CH1: A31-4 (HMCH) - H67-3 (E1)
CH2: A31-14 (HMCL) - H67-3 (E1)
Condition Ignition switch ON

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


HINT:
·

Perform this inspection with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the ignition switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.
A454552

Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

5.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A455011

Check the connection condition of the low voltage connectors of the inverter with converter assembly and the contact pressure of each terminal. Check the terminals for deformation, and the connector for water and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

NOTICE:

Before disconnecting the connector, confirm that it is properly connected by checking that the claws of the lock levers are engaged and that the connector cannot be pulled off.


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C


HINT:

When connecting the connector, connect it with the lock levers raised. Rotate each lock lever downward and make sure that the connector is securely connected. When a lock lever is fully lowered, a click will be heard as its claw engages. After the click is heard, pull up on the connector to confirm that it is securely connected.




A

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.

Disconnect the A31 hybrid vehicle control ECU connector.


d.
C410416C03
0.417,1.115 0.781,1.333 0.365,0.219 1.417,2.458 1.917,2.708 0.5,0.25 1.5,1.115 1.417,0.427 true 1.615,1.115 2.344,0.448 true 0.802,4.219 1.333,3.531 true 1.438,3.646 1.875,4.208 true 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 0.188,2.167 0.5,2.323 0.313,0.156 10 false *b 0.469,1.135 0.802,1.313 0.333,0.177 10 false A55 1.521,2.51 1.823,2.698 0.302,0.188 10 false A31 1.219,0.229 1.833,0.427 0.615,0.198 10 false HMCH 2.375,0.26 2.99,0.458 0.615,0.198 10 false HMCL 0.51,4.281 1.125,4.479 0.615,0.198 10 false HMCH 1.844,4.26 2.458,4.458 0.615,0.198 10 false HMCL
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A55-3 (HMCH) - A31-4 (HMCH) Ignition switch off Below 1 Ω
A55-4 (HMCL) - A31-14 (HMCL) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A55-3 (HMCH) or A31-4 (HMCH) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A55-4 (HMCL) or A31-14 (HMCL) - Body ground and other terminals Ignition switch off 10 kΩ or higher


HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured resistance is as specified.

Check that each connector between the inverter with converter assembly and hybrid vehicle control ECU is not loose or disconnected.



e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-3 (HMCH) or A31-4 (HMCH) - Body ground and other terminals Ignition switch ON Below 1 V
A55-4 (HMCL) or A31-14 (HMCL) - Body ground and other terminals Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the hybrid vehicle control ECU and inverter with converter assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the ignition switch off.


i.

Reconnect the A31 hybrid vehicle control ECU connector.


j.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

7.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.
C408933C02
1.469,0.125 1.854,0.427 0.385,0.302 1.042,1.833 1.344,1.135 true 1.833,1.813 1.469,1.302 true 1.552,0.208 2.01,0.406 0.458,0.198 10 false A31 0.865,1.854 1.479,2.052 0.615,0.198 10 false HMCH 1.708,1.833 2.323,2.031 0.615,0.198 10 false HMCL 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-4 (HMCH) - A31-14 (HMCL) Ignition switch off 80 to 170 Ω



c.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY