Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C12F812  ECB Solenoid Control "A" Circuit Short to Battery  C12F814  ECB Solenoid Control "A" Circuit Short to Ground or Open  


DESCRIPTION

The main relay is built into the No. 1 skid control ECU (brake booster with master cylinder assembly).

The main relay supplies power to the switching solenoid and the linear solenoid.

The main relay remains on for approximately 4 minutes after the ignition switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C12F812 ECB Solenoid Control "A" Circuit Short to Battery When there is a main relay off command from the ECU, 3.5 V or more is detected at terminal BS for 4.5 seconds or more.
·

Short in main relay circuit

·

Main relay internal stuck

·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


·

Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

·

ECB: Electronically Controlled Brake System


C12F814 ECB Solenoid Control "A" Circuit Short to Ground or Open Either of the following is detected:
·

When the ignition switch is turned to ON (READY):

The BS terminal voltage is less than 3.8 V for 0.05 seconds or more, when the IG1 terminal voltage is 9.5 V or more and operation of the main relay is requested.

·

When the ignition switch is off:

The BS terminal voltage is less than 3.8 V for 0.05 seconds or more, when operation of the main relay is requested.


·

Open or short in main relay circuit

·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


·

Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

·

ECB: Electronically Controlled Brake System



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.READ VALUE USING GTS (BS VOLTAGE)
a.

Perform the Active Test and operate the main relay.


b.

Monitor the value of BS Voltage when the Active Test is being performed.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Main Relay Main relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BS Voltage BS voltage value Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to auxiliary battery voltage
Chassis > Brake Booster > Active Test
Active Test Display
ECB Main Relay
Data List Display
BS Voltage
50004 466 41 295
Result:
Result Proceed to
During the Active Test, the voltage indicated by BS Voltage increases to the approximate voltage of the auxiliary battery. A
During the Active Test, the voltage indicated by BS Voltage remains low around 0 V. B


HINT:

During the Active Test, the voltage indicated by BS Voltage changes in proportion to the voltage of the auxiliary battery.




A

2.CLEAR DTC

B

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
DTCs C12F812 and C12F814 are not output. A
DTCs C12F812 and/or C12F814 are output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
a.
C423268C02
0.438,0.698 0.844,0.979 0.406,0.281 2.458,1.667 2.604,1.073 true 2.479,0.896 2.938,1.094 0.458,0.198 10 false +BI1 0.521,0.75 0.979,0.948 0.458,0.198 10 false A44 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-14 (+BI1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.
C423268C01
0.417,0.75 0.833,1 0.417,0.25 2.719,1.01 2.635,1.74 true 2.656,0.823 3.115,1.021 0.458,0.198 10 false BS 0.5,0.781 0.958,0.979 0.458,0.198 10 false A44 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-15 (BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR