Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C139100  Abnormal Leak in Accumulator  


DESCRIPTION

This DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake booster with master cylinder assembly or brake booster with accumulator pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C139100 Abnormal Leak in Accumulator Either of the following is detected:
·

When the brake pedal is not depressed and the pump motor is operating, the accumulator pressure sensor value does not increase a certain number of times.

·

When the brake pedal is not depressed and the pump motor is not operating, the accumulator pressure sensor decrease rate exceeds a certain threshold a certain number of times.


·

Brake fluid leaks

·

Brake booster with master cylinder assembly

(Malfunctioning internal seal etc.)

·

Brake booster with accumulator pump assembly

(Accumulator internal gas pressure decrease, etc.)


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.READ VALUE USING GTS (SERVO PRESSURE)
a.

Perform the Active Test and operate the linear solenoid (SLR) in the brake booster with master cylinder assembly.


b.

Check that the servo pressure output value does not increase when performing the Active Test.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid Start (Activate)
Solenoid SLR
(It is possible to set the current)
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake Booster > Active Test
Active Test Display
ECB Solenoid (SLR)
Data List Display
Servo Pressure
50004 466 42 210
OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:
·

If the servo pressure output value increases, an internal brake fluid leak in the brake booster with master cylinder assembly is suspected.

·

Perform the Active Test with the current set to maximum.




Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

2.CHECK OPERATING TIME OF PUMP MOTOR
2.CHECK OPERATING TIME OF PUMP MOTOR
a.

With the ignition switch is turned to ON (READY), check the operation of the pump motor.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
50003 466 96

Result:
Result Proceed to
The pump motor operates once or more within 20 seconds or operates for 10 seconds or more each time. A
Other than above. B



A

3.CHECK FOR FLUID LEAK

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CHECK FOR FLUID LEAK
a.

Check for brake fluid leaks in the line from the brake booster with accumulator pump assembly to the brake booster with master cylinder assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C120200

OK:

There are no brake fluid leaks.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

for Brake Booster with Master Cylinder Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model LHD)>REMOVAL

for Brake Booster with Accumulator Pump Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>REMOVAL


NG

REPAIR MALFUNCTIONING PART