Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  VSC OFF Switch Circuit  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the "Traction Control Turned Off" will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C427345E01
0.906,0.917 1.521,1.115 0.615,0.198 10 false CANL 0.885,1.74 1.5,1.938 0.615,0.198 10 false CANH 1.417,0.74 1.729,0.938 0.313,0.198 10 false 31 1.406,1.552 1.719,1.75 0.313,0.198 10 false 32 5.073,0.74 5.385,0.938 0.313,0.198 10 false 43 5.073,1.552 5.385,1.75 0.313,0.198 10 false 27 5.354,0.917 5.969,1.115 0.615,0.198 10 false CANL 5.354,1.74 5.969,1.938 0.615,0.198 10 false CANH 3.469,2.75 3.625,2.948 0.156,0.198 10 false 2 4.542,2.75 4.698,2.948 0.156,0.198 10 false 5 0.135,3.906 0.594,4.104 0.458,0.198 10 false H21 3.542,3.24 4,3.438 0.458,0.198 10 false P6 3.542,3.406 4.74,3.688 1.198,0.281 10 false VSC OFF Switch 3.688,2.99 3.844,3.188 0.156,0.198 10 false E 4.344,2.979 4.5,3.177 0.156,0.198 10 false + 5.156,2.74 5.469,2.938 0.313,0.198 10 false 9 5.365,2.99 5.823,3.188 0.458,0.198 10 false CSW 5.104,3.906 5.563,4.104 0.458,0.198 10 false A57 5.094,4.083 6.99,4.49 1.896,0.406 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 2.906,4.344 6.573,4.542 3.667,0.198 10 false : CAN Communication Line 0.125,4.073 4.104,4.271 3.979,0.198 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Check that the indicator light and mode condition on the GTS change according to VSC OFF switch operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / VSC expert mode (VSC expert mode MID ON) / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
VSC expert mode (VSC expert mode MID ON): VSC expert mode
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Chassis > Brake/EPB > Data List
Tester Display
TRC(TRAC)/VSC OFF Mode
50003 435 45
Standard:
Switch Operation Mode Condition Display Multi-information Display (Traction Control Turned Off) VSC OFF Indicator Light
Not pressed Normal mode (TRC(TRAC) ON/VSC ON) Not displayed Does not come on
Pressing the VSC OFF switch TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) Displayed Does not come on
Pressing and holding the VSC OFF switch VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

2.INSPECT VSC OFF SWITCH

B

C

2.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.


b.

Inspect the VSC OFF switch.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION

OK:

The VSC OFF switch is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-9 (CSW) - P6-5 (+) Always Below 1 Ω
A57-9 (CSW) or P6-5 (+) - Body ground Always 10 kΩ or higher
P6-2 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR