Refer to DTC C051212.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C051223 | Right Rear Wheel Speed Sensor Signal Stuck Low | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.*2 ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.*1 ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more.*2 ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more.*1 |
·
Rear skid control sensor RH*1 ·
Rear speed sensor RH (rear axle hub and bearing assembly RH)*2 ·
Speed sensor installation ·
Skid control sensor wire RH (No. 1 parking brake wire assembly) ·
Wire harness and connector ·
Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
*1: for 4WD/AWD
*2: for 2WD
Refer to DTC C051212.
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| for 4WD/AWD. | A |
| for 2WD. | B |
A
B
| *1 | Rear Skid Control Sensor RH |
| *a | Correct |
| *b | Incorrect |
| *c | 8.5 N*m (87 kgf*cm, 75 in.*lbf) |
| *d | No clearance |
Check the rear skid control sensor RH installation.
There is no clearance between the rear skid control sensor RH and the rear axle carrier RH.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear skid control sensor RH.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for 4WD/AWD)>REMOVAL
Check the rear skid control sensor tip RH.
The rear skid control sensor tip RH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the rear skid control sensor RH, clean the rear skid control sensor RH.
If the rear skid control sensor RH is damaged, replace the rear skid control sensor RH with a new one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a road test.
Check the rear skid control sensor RH output value.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of skid control sensor wire RH (No. 1 parking brake wire assembly) |
| *b | to Sensor Side Connector |
| *c | to Vehicle Side Connector |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the u3 and uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u3-1 (+) - uM1-3 (RR+) | Always | Below 1 Ω |
| u3-1 (+) or uM1-3 (RR+) - Body ground and other terminals | Always | 10 kΩ or higher |
| u3-2 (-) - uM1-4 (RR-) | Always | Below 1 Ω |
| u3-2 (-) or uM1-4 (RR-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM1-3 (RR+) - A57-20 (RR+) | Always | Below 1 Ω |
| uM1-3 (RR+) or A57-20 (RR+) - Body ground | Always | 10 kΩ or higher |
| uM1-4 (RR-) - A57-19 (RR-) | Always | Below 1 Ω |
| uM1-4 (RR-) or A57-19 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the component with the rear speed sensor rotor RH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 4WD/AWD)>REMOVAL
Check the rear speed sensor rotor RH.
The rear speed sensor rotor RH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the rear speed sensor rotor RH, clean the rear speed sensor rotor RH.
Do not use parts cleaner when cleaning the rear speed sensor rotor RH.
If the rear speed sensor rotor RH is damaged, replace the rear speed sensor rotor RH with a new one.
The rear speed sensor rotor RH is incorporated into the rear axle hub and bearing assembly RH.
If the rear speed sensor rotor RH needs to be replaced, replace it together with the rear axle hub and bearing assembly RH.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The rear speed sensor rotor RH is damaged.) | B |
| NG (There is foreign matter on the rear speed sensor rotor RH.) | C |
A
B
C
| *1 | Rear Speed Sensor RH |
| *a | Correct |
| *b | Incorrect |
| *c | No clearance |
Check the rear speed sensor RH installation.
There is no clearance between the rear speed sensor RH and the rear axle hub and bearing assembly RH.
Because the rear axle hub and bearing assembly RH cannot be disassembled, if the rear speed sensor RH needs replacement, replace the rear axle hub and bearing assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a road test.
Check the rear speed sensor RH output value.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of skid control sensor wire RH (No. 1 parking brake wire assembly) |
| *b | to Sensor Side Connector |
| *c | to Vehicle Side Connector |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the u3 and uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u3-2 (+) - uM1-3 (RR+) | Always | Below 1 Ω |
| u3-2 (+) or uM1-3 (RR+) - Body ground and other terminals | Always | 10 kΩ or higher |
| u3-1 (-) - uM1-4 (RR-) | Always | Below 1 Ω |
| u3-1 (-) or uM1-4 (RR-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM1-3 (RR+) - A57-20 (RR+) | Always | Below 1 Ω |
| uM1-3 (RR+) or A57-20 (RR+) - Body ground | Always | 10 kΩ or higher |
| uM1-4 (RR-) - A57-19 (RR-) | Always | Below 1 Ω |
| uM1-4 (RR-) or A57-19 (RR-) - Body ground | Always | 10 kΩ or higher |
The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.
If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG