Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  P057112  Brake Switch "A" Circuit Short to Battery  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

DTCs may be stored if either of the following occurs:

·

Stop light switch assembly stuck on malfunction.

·

The accelerator and brake pedals are depressed simultaneously.*


HINT:

*: The No. 2 skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
P057112 Brake Switch "A" Circuit Short to Battery When the stop light switch assembly is stuck on, the vehicle decelerates from 30 km/h (19 mph) or more to 3 km/h (2 mph) or less 10 times or more.
·

Stop light switch assembly

·

Stop light switch assembly installation

·

Wire harness and connector

·

STP circuit

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model LHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation is normal.


Result:
Proceed to
OK
NG



OK

2.CHECK BRAKE ACTUATOR ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

2.CHECK BRAKE ACTUATOR ASSEMBLY
a.
C401043C74
0.417,0.656 0.76,0.885 0.344,0.229 2.417,1.646 2.167,1.063 true 0.469,0.677 0.927,0.875 0.458,0.198 10 false A42 0.188,0.188 0.646,0.385 0.458,0.198 10 false *a 2.313,1.677 2.771,1.875 0.458,0.198 10 false OUT
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (OUT) - Body ground Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK STOP LIGHT SWITCH ASSEMBLY
3.CHECK STOP LIGHT SWITCH ASSEMBLY
a.
C401044C80
0.49,0.646 0.833,0.854 0.344,0.208 1.26,1.25 1.115,1.677 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *a 0.542,0.667 1,0.885 0.458,0.219 10 false A42 0.979,1.708 1.396,1.906 0.417,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (OUT) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

4.CHECK FOR SHORT TO +B IN STP CIRCUIT
4.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses, connectors, ECUs and stop lights).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART