Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C00632A  Yaw Rate Sensor Signal Stuck In Range  C05201C  Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range  C05202A  Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range  C052096  Multi-axis Acceleration Sensor Module "A" Component Internal Failure  


DESCRIPTION

The yaw rate sensor has a built-in acceleration sensor.

These DTCs are stored when the No. 2 skid control ECU (brake actuator assembly) receives an internal malfunction signal from the yaw rate sensor.

The No. 2 skid control ECU (brake actuator assembly) receives signals from the yaw rate sensor via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate sensor and the CAN communication system, DTC U012587 is output. When DTC U012587 is output together with C00632A, C05201C, C05202A and/or C052096, inspect and repair the trouble areas indicated by U012587 first.


DTCs may be stored if either of the following occurs:

·

Yaw rate sensor installation abnormality.

·

Yaw rate sensor signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
C00632A Yaw Rate Sensor Signal Stuck In Range A yaw rate sensor stuck malfunction status continues.
·

Yaw rate sensor installation

·

Yaw rate sensor


Output ECU: No. 2 skid control ECU (brake actuator assembly)
C05201C Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed sensor exceeds 0.35 G for 60 seconds or more.
·

Acceleration sensor (yaw rate sensor) installation

·

Acceleration sensor (yaw rate sensor)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
C05202A Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range Any of the following is detected:
·

The acceleration sensor output value does not change 16 times or more as the vehicle speed drops from 30 km/h (19 mph) to 0 km/h (0 mph).

·

A GL1 stuck malfunction status continues.

·

A GL2 stuck malfunction status continues.


·

Acceleration sensor (yaw rate sensor) installation

·

Acceleration sensor (yaw rate sensor)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
C052096 Multi-axis Acceleration Sensor Module "A" Component Internal Failure Either of the following is detected:
·

A signal indicating an acceleration sensor internal malfunction is received

·

Output values of GL1 and GL2 (front and rear, left and right) are outside permitted output range for 60 seconds or more.


·

Acceleration sensor (yaw rate sensor) installation

·

Acceleration sensor (yaw rate sensor)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the yaw rate sensor, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK YAW RATE SENSOR INSTALLATION
a.

Check that the yaw rate sensor has been installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>INSTALLATION

OK:

The yaw rate sensor is tightened to the specified torque.

The yaw rate sensor is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

NG