Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM
RM37A0E _52 Drivetrain _086861 GF2A TRANSFER / 4WD / AWD _0421155 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF2A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C05F51C  4WD/AWD Front/Rear Range Actuator Control Circuit Performance Circuit Voltage Out of Range  


DESCRIPTION

The 4WD ECU assembly receives signals from each sensor to control clutch fluid pressure for limiting the center differential operation, which distributes torque according to the driving conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
C05F51C 4WD/AWD Front/Rear Range Actuator Control Circuit Performance Circuit Voltage Out of Range When all of the following continue for 1 second or more:
·

IG1 voltage is 9.5 V or more.

·

The current requested by the 4WD linear solenoid (electro magnetic control coupling sub-assembly) is either 0 A or greater than 0.8 A.

·

Open or short occurs in the linear solenoid circuit.


·

Wire harness or connector

·

4WD linear solenoid (electro magnetic control coupling sub-assembly)

·

4WD ECU assembly


Displayed Yes

DTC Detection Conditions: C05F51C
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition IG1 voltage is 9.5 V or more, the current requested by the 4WD linear solenoid (electro magnetic control coupling sub-assembly) is 0 A. ○ -
IG1 voltage is 9.5 V or more, the current requested by the 4WD linear solenoid (electro magnetic control coupling sub-assembly) is greater than 0.8 A. - ○
Malfunction Status Short occurs in the linear solenoid circuit. ○ -
Open occurs in the linear solenoid circuit. - ○
Detection Time 1 second or more 1 second or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be stored when conditions for either of the patterns in the table above is met.


WIRING DIAGRAM

C415580E10
0.563,2.229 0.875,2.427 0.313,0.198 10 false s8 0.573,2.406 4.167,2.698 3.594,0.292 10 false Electro Magnetic Control Coupling Sub-assembly 4.688,2.406 6.281,2.698 1.594,0.292 10 false 4WD ECU Assembly 4.688,2.24 5,2.438 0.313,0.198 10 false M42 3.25,0.813 4.438,1.083 1.188,0.271 10 false BSF 3.25,1.313 4.438,1.583 1.188,0.271 10 false SLC 4.76,1.323 5.948,1.594 1.188,0.271 10 false SLC- 4.76,0.802 5.948,1.073 1.188,0.271 10 false SLC+ 3.667,0.802 3.979,1 0.313,0.198 10 false 1 3.677,1.313 3.99,1.51 0.313,0.198 10 false 2 4.542,1.292 4.854,1.49 0.313,0.198 10 false 3 4.542,0.813 4.854,1.01 0.313,0.198 10 false 4 5.594,0.354 6.073,0.625 0.479,0.271 10 false 12 V 1.25,1.719 3.323,2.052 2.073,0.333 10 false 4WD Linear Solenoid

CAUTION / NOTICE / HINT

NOTICE:
·

When the 4WD ECU assembly is replaced, before removing the 4WD ECU assembly, it is necessary to perform ECU Data Save to save the original 4WD ECU assembly information.

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>CALIBRATION

·

After performing repairs, clear the DTCs and check that the DTCs are not output again.

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY)
a.
C428398C01
1.51,0.063 1.927,0.313 0.417,0.25 0.531,0.635 0.698,0.635 0.698,0.635 1.5,0.948 true 1.917,0.958 2.75,0.646 2.75,0.646 2.917,0.646 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 1.573,0.104 2.031,0.302 0.458,0.198 10 false M42 2.969,0.573 3.375,0.75 0.406,0.177 10 false SLC+ 0.167,0.573 0.573,0.75 0.406,0.177 10 false SLC-
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the M42 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-4 (SLC+) - M42-3 (SLC-) 20°C (68°F) 2.2 to 2.6 Ω
M42-4 (SLC+) - Body ground Always 10 kΩ or higher
M42-3 (SLC-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY
2.INSPECT ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY
a.
C131916C01
1.575,1.186 1.117,1.614 false 1.813,1.187 2.229,1.591 false 0.844,1.626 1.149,1.778 0.306,0.152 10 SLC 2.161,1.634 2.466,1.786 0.306,0.152 10 BSF 0,0 0.313,0.156 0.313,0.156 10 *a
*a Component without harness connected
(4WD Linear Solenoid [Electro Magnetic Control Coupling Sub-assembly])


Disconnect the s8 4WD linear solenoid (electro magnetic control coupling sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BSF) - 2 (SLC) 20°C (68°F) 2.2 to 2.6 Ω
1 (BSF) - Body ground Always 10 kΩ or higher
2 (SLC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG