Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM
RM37A0E _52 Drivetrain _086861 GF2A TRANSFER / 4WD / AWD _0421155 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF2A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C13F21C  4WD/AWD Rear Differential Oil Temperature Sensor Circuit Voltage Out of Range  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
C13F21C 4WD/AWD Rear Differential Oil Temperature Sensor Circuit Voltage Out of Range
·

Even though the calorific value of the rear differential carrier assembly estimated from driving conditions is high enough, the temperature of the temperature sensor remains at approximately -40°C for 1 second or more

·

Even though the engine coolant temperature received from the ECM is below 35°C, the ignition switch was turned from off to ON 2 times with the temperature of the temperature sensor fixed at approximately 80°C or more (shorted)

·

The temperature sensor power source voltage is 0.2 V or less for 1 second or more

·

The temperature sensor signal circuit voltage is 4.5 V or higher for 1 second or more


·

Wire harness or connector

·

Temperature sensor

·

4WD ECU assembly


Displayed Yes

DTC Detection Conditions: C13F21C
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition The calorific value of the rear differential carrier assembly estimated from driving conditions is high enough ○ - - -
The engine coolant temperature received from the ECM is below 35°C - ○ - -
Malfunction Status The temperature of the temperature sensor remains at approximately -40°C ○ - - -
The temperature of the temperature sensor fixed at approximately 80°C or more (shorted) - ○ - -
The temperature sensor power source voltage is 0.2 V or less - - ○ -
The temperature sensor signal circuit voltage is 4.5 V or higher - - - ○
Detection Time 1 second or more - 1 second or more 1 second or more
Number of Trips 1 trip 2 trips 1 trip 1 trip

HINT:

DTC will be stored when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C408922E02
6.385,0.25 6.698,0.448 0.313,0.198 10 false 5V 5.021,1.229 5.625,1.427 0.604,0.198 10 false THR+ 1.781,2.021 2.385,2.219 0.604,0.198 10 false THR+ 2.99,2.01 3.594,2.208 0.604,0.198 10 false THR- 5.031,2.01 5.635,2.208 0.604,0.198 10 false THR- 1.896,2.677 3.313,2.896 1.417,0.219 10 false Temperature Sensor 1.594,2.688 2.198,2.885 0.604,0.198 10 false s4 4.802,3.219 5.406,3.417 0.604,0.198 10 false M41 5.219,3.219 6.635,3.438 1.417,0.219 10 false 4WD ECU Assembly 4.708,1.229 5.021,1.427 0.313,0.198 10 false 13 4.719,2.01 5.031,2.208 0.313,0.198 10 false 21 3.438,1.99 3.75,2.188 0.313,0.198 10 false 2 1.563,2 1.875,2.198 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When the 4WD ECU assembly is replaced, before removing the 4WD ECU assembly, it is necessary to perform ECU Data Save to save the original 4WD ECU assembly information.

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>CALIBRATION

·

After performing repairs, clear the DTCs and check that the DTCs are not output again.

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - TEMPERATURE SENSOR)
a.

Disconnect the M41 4WD ECU assembly connector.


b.

Disconnect the s4 temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-13 (THR+) - s4-1 (THR+) Always Below 1 Ω
M41-21 (THR-) - s4-2 (THR-) Always Below 1 Ω
M41-13 (THR+) or s4-1 (THR+) - Body ground and other terminals Always 10 kΩ or higher
M41-21 (THR-) or s4-2 (THR-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT TEMPERATURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT TEMPERATURE SENSOR
a.

Disconnect the s4 temperature sensor connector.


b.
C325714C05
1.302,1.865 0.74,2.563 true 2.083,1.865 2.76,2.49 true 0.125,0.156 0.438,0.354 0.313,0.198 10 false *a 0.49,2.594 1.104,2.792 0.615,0.198 10 false THR- 2.74,2.521 3.188,2.833 0.448,0.313 10 false THR+
*a Component without harness connected
(Temperature Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THR+) - 2 (THR-) 20°C (68°F) 0.9 to 30 kΩ



Result:
Proceed to
OK
NG



OK

NG