Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE VECTORING AWD SYSTEM
RM37A0E _52 Drivetrain _086861 GF2A TRANSFER / 4WD / AWD _0421156 DYNAMIC TORQUE VECTORING AWD SYSTEM C

GF2A TRANSFER / 4WD / AWD  DYNAMIC TORQUE VECTORING AWD SYSTEM  C05E71C  4WD/AWD Clutch "B" Actuator Control Circuit Performance Circuit Voltage Out of Range  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
C05E71C 4WD/AWD Clutch "B" Actuator Control Circuit Performance Circuit Voltage Out of Range
·

The command current of the rear 4WD linear solenoid is 0 A and the short circuit continues for 1 second or more

·

The command current of the rear 4WD linear solenoid is 3.0 A or higher and the open circuit continues for 0.5 seconds or more


·

Wire harness or connector

·

Rear 4WD linear solenoid (rear differential carrier assembly)

·

4WD ECU assembly


Displayed Yes

DTC Detection Conditions: C05E71C
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition The command current of the rear 4WD linear solenoid is 0 A ○ -
The command current of the rear 4WD linear solenoid is 3.0 A - ○
Malfunction Status Short circuit ○ -
Open circuit - ○
Detection Time 1 second or more 0.5 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be stored when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C409017E09
0.646,2.875 0.958,3.073 0.313,0.198 10 false s2 0.979,2.875 3.573,3.354 2.594,0.479 10 false Rear Differential Carrier Assembly 2.677,1.281 3.208,1.51 0.531,0.229 10 false SLR+ 2.688,1.958 3.219,2.188 0.531,0.229 10 false SLR- 4.229,2.531 4.76,2.76 0.531,0.229 10 false SLRS 4.24,1.969 4.771,2.198 0.531,0.229 10 false SLR- 4.208,1.271 4.74,1.5 0.531,0.229 10 false SLR+ 3.198,1.271 3.729,1.5 0.531,0.229 10 false 1 3.229,1.969 3.76,2.198 0.531,0.229 10 false 2 3.958,1.271 4.49,1.5 0.531,0.229 10 false 5 3.979,1.958 4.51,2.188 0.531,0.229 10 false 6 3.938,2.396 4.469,2.625 0.531,0.229 10 false 16 4.625,3.177 6.813,3.5 2.188,0.323 10 false 4WD ECU Assembly 4.208,3.167 4.521,3.365 0.313,0.198 10 false M42 5.26,0.208 5.792,0.438 0.531,0.229 10 false 12V 1.25,2.313 3.323,2.594 2.073,0.281 10 false Rear 4WD Linear Solenoid

CAUTION / NOTICE / HINT

NOTICE:
·

When the 4WD ECU assembly is replaced, before removing the 4WD ECU assembly, it is necessary to perform ECU Data Save to save the original 4WD ECU assembly information.

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE VECTORING AWD SYSTEM>CALIBRATION

·

After performing repairs, clear the DTCs and check that the DTCs are not output again.

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE VECTORING AWD SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - REAR 4WD LINEAR SOLENOID (REAR DIFFERENTIAL CARRIER ASSEMBLY))
a.

Disconnect the M42 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-5 (SLR+) - M42-6 (SLR-) 20°C (68°F) 0.73 to 0.83 Ω
M42-5 (SLR+) - Body ground Always 10 kΩ or higher



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M42-6 (SLR-) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - REAR 4WD LINEAR SOLENOID (REAR DIFFERENTIAL CARRIER ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - REAR 4WD LINEAR SOLENOID (REAR DIFFERENTIAL CARRIER ASSEMBLY))
a.

Disconnect the M42 4WD ECU assembly connector.


b.

Disconnect the s2 rear 4WD linear solenoid (rear differential carrier assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-5 (SLR+) - s2-1 (SLR+) Always Below 1 Ω
M42-6 (SLR-) - s2-2 (SLR-) Always Below 1 Ω
M42-5 (SLR+) or s2-1 (SLR+) - Body ground Always 10 kΩ or higher
M42-6 (SLR-) or s2-2 (SLR-) - Body ground Always 10 kΩ or higher
M42-5 (SLR+) or s2-1 (SLR+) - M42-6 (SLR-) or s2-2 (SLR-) Always 10 kΩ or higher
M42-5 (SLR+) - M42-16 (SLRS) Always 10 kΩ or higher
M42-6 (SLR-) - M42-16 (SLRS) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M42-5 (SLR+) or s2-1 (SLR+) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR