Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Vectoring AWD)
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0421149 REAR DIFFERENTIAL CARRIER ASSEMBLY(for Dynamic Torque Vectoring AWD) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for Dynamic Torque Vectoring AWD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during torque vectoring differential carrier assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leaks from exhaust system Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Electro magnetic control coupling sub-assembly (Electro magnetic control coupling sub-assembly LH, electro magnetic control coupling sub-assembly RH)
·

ECU data initialization

·

ECU data write


Dynamic Torque Vectoring AWD System (Click here)
Torque vectoring differential carrier assembly
·

ECU data initialization

·

Disconnect system function check


Temperature sensor ECU data initialization

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.DRAIN DIFFERENTIAL OIL

Hide 37100 2.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 3.REMOVE REAR DRIVE SHAFT ASSEMBLY

a.

Remove the rear drive shaft assembly LH and RH.

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>REAR DRIVE SHAFT ASSEMBLY (for 2GR-FKS)>REMOVAL


Hide 48812 4.REMOVE REAR STABILIZER BAR

Hide 52391A 5.REMOVE REAR DIFFERENTIAL SUPPORT

a.
C426362

Remove the 4 bolts, 2 nuts and rear differential support from the rear No. 2 differential support and torque vectoring differential carrier assembly.


b.
C426363

Temporarily install the 2 bolts and 2 nuts.


Hide 41110 6.REMOVE TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY

NOTICE:
·

Do not damage the contact surface when removing the torque vectoring differential carrier assembly.

·

The remaining oil may leak out when removing the torque vectoring differential carrier assembly.

·

Securely support the torque vectoring differential carrier assembly while performing this step to avoid excessively tilting or dropping the torque vectoring differential carrier assembly.

·

Remove the bolts and nuts with the torque vectoring differential carrier assembly secured.



a.
C426361

Disconnect the 2 connectors and breather tube.


b.

Disengage the clamp to disconnect the frame wire.


c.

Support the torque vectoring differential carrier assembly with a transmission jack using 2 attachments or equivalent tools as shown in the illustration.

C426364C01
3.823,2.156 4.521,2.156 4.521,2.156 3.479,1.813 true 4.552,2.083 4.771,2.281 0.219,0.198 10 true *a
*a Attachment - -
V100155

Attachment Installation Position - -


CAUTION:

The torque vectoring differential carrier assembly is a heavy component. Make sure that it is supported securely.


NOTICE:

Use attachments or equivalent tools to keep the torque vectoring differential carrier assembly level.



d.

Remove the 4 bolts, 2 nuts and 2 rear lower differential mount stoppers.

HINT:

The nuts have tabs to prevent them from rotating.



e.

Lower the torque vectoring differential carrier assembly slowly to remove the torque vectoring differential carrier assembly.

NOTICE:

Move the transmission jack forward and backward as necessary to prevent the torque vectoring differential carrier assembly from contacting the rear suspension member sub-assembly.



Hide 52380C 7.REMOVE REAR NO. 2 DIFFERENTIAL SUPPORT

a.
C426365

Remove the 2 rear upper differential mount stoppers from the rear No. 2 differential support.


b.
C426366

Remove the 2 bolts, 2 nuts and rear No. 2 differential support from the torque vectoring differential carrier assembly.


Hide 41196 8.REMOVE REAR DIFFERENTIAL DYNAMIC DAMPER

a.
C426367

Remove the bolt and rear differential dynamic damper from the rear No. 2 differential support.


Hide 41196C 9.REMOVE REAR NO. 2 DIFFERENTIAL DYNAMIC DAMPER

a.
C426368

Remove the 2 bolts, 2 rear upper differential mount stoppers and rear No. 2 differential dynamic damper from the differential support.


Hide 52391B 10.REMOVE DIFFERENTIAL SUPPORT

a.
C426369

Remove the 3 bolts and differential support from the torque vectoring differential carrier assembly.