Refer to DTC P323A19.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P323A19
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory | Note |
|---|---|---|---|---|---|---|
| P30DF62 | Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure | The following conditions is met for 1 second or more (1 trip detection logic):
·
Difference in temperature between thermistor 1 and thermistor 2 of the engine stop and start ECU is 40°C (72°F) or higher. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P30DF |
| P30EF4B | Backup Boost Converter Circuit Board Over Temperature | The following conditions is met for 1 second or more (1 trip detection logic):
·
Engine stop and start ECU thermistor temperature is 135°C (275°F) or higher. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P30EF |
| P323A00 | Backup Boost Converter "A" | The following conditions is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323A |
| P323A16 | Backup Boost Converter "A" Circuit Voltage Below Threshold | One of the following conditions is met for 2 second or more (1 trip detection logic):
·
B41 or IG41 voltage is 6.0 V or less and backup boost converter output overcurrent is not detected. ·
B42 or B43 voltage is 6.0 V or less, backup boost converter is not overheating and backup boost converter output overcurrent is not detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323A |
| P323AA2 | Backup Boost Converter "A" System Voltage Low | The following conditions is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323A |
| P323B29 | Backup Boost Converter "A" Control Circuit Signal Invalid | The following conditions is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323C |
| P323B38 | Backup Boost Converter "A" Control Circuit Signal Cycle Invalid | The following conditions is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323C |
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.
Check that DTCs are not output.
STOP AND START SYSTEM OPERATION CHECK
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK
Refer to DTC P323A19.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P323A19
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR
Using the GTS, read the Freeze Frame Data before troubleshooting. System condition information is recorded as Freeze Frame Data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
Disconnect the engine stop and start ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-1 (BIN2) - Body ground | Always | 9.5 to 14 V |
| A33-3 (BIN1) - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
Disconnect the engine stop and start ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H66-21 (IG1) - Body ground | Ignition switch ON | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-6 (DGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Remove the FOG FR relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the navigation ECU connector. (w/ Navigation System)
Disconnect the meter mirror assembly connector. (w/ Headup Display)
Disconnect the radio and display receiver assembly connector.
Disconnect the television display assembly connector. (w/ Rear Seat Entertainment System)
Disconnect the inner rear view mirror assembly connector. (w/ EC Mirror or Digital Inner Mirror)
Disconnect the front door ambient light LH (front door trim board sub-assembly LH) connector. (w/ Ambient Illumination Light)
Disconnect the front door ambient light RH (front door trim board sub-assembly RH) connector. (w/ Ambient Illumination Light)
Disconnect the rear door ambient light LH (rear door trim board sub-assembly LH) connector. (w/ Ambient Illumination Light)
Disconnect the rear door ambient light RH (rear door trim board sub-assembly RH) connector. (w/ Ambient Illumination Light)
Disconnect the front passenger side tray illumination light (No. 1 instrument panel light sub-assembly) connector. (w/ Ambient Illumination Light)
Disconnect the center tray illumination light (No. 1 instrument panel light sub-assembly) connector. (w/ Ambient Illumination Light)
Disconnect the air conditioning control assembly connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Disconnect the millimeter wave radar sensor assembly connector.
Disconnect the clearance warning ECU assembly connector.
Disconnect the blind spot monitor sensor LH connector.
Disconnect the blind spot monitor sensor RH connector.
Disconnect the No. 2 air conditioning control assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H66-2 (B41) - 2 (FOG FR relay) | Always | Below 1 Ω |
| H66-2 (B41) - 5 (FOG FR relay) | Always | Below 1 Ω |
| H66-2 (B41) - H18-10 (+B)*1 | Always | Below 1 Ω |
| H66-2 (B41) - H31-2 (B)*2 | Always | Below 1 Ω |
| H66-12 (B42) - H1-4 (+B1) | Always | Below 1 Ω |
| H66-11 (B43) - R16-1 (+B)*3 | Always | Below 1 Ω |
| H66-11 (B43) -J26-2 (+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -J10-2 (+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -K10-2 (+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -K5-2 (+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -H69-2 (ILL+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -H68-2 (ILL+)*5 | Always | Below 1 Ω |
| H66-3 (IG41) - R1-1 (IG)*4 | Always | Below 1 Ω |
| H66-3 (IG41) - H31-1 (IG)*2 | Always | Below 1 Ω |
| H66-3 (IG41) - H27-6 (IG+) | Always | Below 1 Ω |
| H66-3 (IG41) - H59-11 (IG1) | Always | Below 1 Ω |
| H66-3 (IG41) - B6-8 (IGB) | Always | Below 1 Ω |
| H66-3 (IG41) - H46-1 (IG) | Always | Below 1 Ω |
| H66-3 (IG41) - M43-5 (BLB) | Always | Below 1 Ω |
| H66-3 (IG41) - M2-5 (BRB) | Always | Below 1 Ω |
| H66-3 (IG41) - T2-9 (IG) | Always | Below 1 Ω |
| H66-2 (B41) or 2 (FOG FR relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-2 (B41) or 5 (FOG FR relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-2 (B41) or H18-10 (+B)*1 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-2 (B41) or H31-2 (B)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-12 (B42) or H1-4 (+B1) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or R16-1 (+B)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or J26-2 (+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or J10-2 (+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or K10-2 (+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or K5-2 (+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or H69-2 (ILL+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or H68-2 (ILL+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or R1-1 (IG)*4 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or H31-1 (IG)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or H27-6 (IG+) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or H59-11 (IG1) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or B6-8 (IGB) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or H46-1 (IG) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or M43-5 (BLB) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or M2-5 (BRB) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or T2-9 (IG) - Body ground and other terminals | Always | 10 kΩ or higher |
*1: w/ Navigation System
*2: w/ Headup Display
*3: w/ Rear Seat Entertainment System
*4: w/ EC Mirror or Digital Inner Mirror
*5: w/ Ambient Illumination Light
| Proceed to |
|---|
| OK |
| NG |
OK
NG