Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.11
RM37A0E _51 Engine / Hybrid System _094408 STOP AND START _0444545 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Stop and Start Cancel Switch Circuit  


DESCRIPTION

Stop and start control can be disabled by pressing the stop and start system cancel switch (ecorun cancel switch assembly). The stop and start system cancel switch (ecorun cancel switch assembly) is a momentary-type switch that switches between on and off when the switch is pressed. While stop and start control is disabled, the stop and start cancel indicator is illuminated to inform the driver.

WIRING DIAGRAM

A348169E52
3.531,0.896 4.5,1.135 0.969,0.24 10 false 5 2.063,0.885 2.385,1.083 0.323,0.198 10 false 2 1.385,1.458 1.969,1.74 0.583,0.281 10 false P7 1.385,1.615 4.271,2.198 2.885,0.583 10 false Stop and Start System Cancel Switch (Ecorun Cancel Switch Assembly) 5.188,1.458 5.656,1.656 0.469,0.198 10 false H66 5.5,0.917 5.854,1.219 0.354,0.302 10 false 5 5.698,1.042 6.26,1.313 0.563,0.271 10 false ECAN 5.188,1.604 6.938,1.917 1.75,0.313 10 false Engine Stop and Start ECU 3.156,0.844 3.615,1.042 0.458,0.198 10 false ECU 2.26,0.844 2.719,1.042 0.458,0.198 10 false GND

PROCEDURE

1.READ VALUE USING GTS (STOP&START CANCEL SWITCH)
a.

Read the value when the stop and start system cancel switch (ecorun cancel switch assembly) is pressed.

Powertrain > Stop and Start > Data List
Tester Display
Stop&Start Cancel Switch
50003 392 208
OK:
GTS Display Condition Normal Condition
Stop&Start Cancel Switch Stop and start system cancel switch (ecorun cancel switch assembly) is pressed ON
Stop and start system cancel switch (ecorun cancel switch assembly) is not pressed OFF



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (ECORUN CANCEL SWITCH ASSEMBLY)
2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (ECORUN CANCEL SWITCH ASSEMBLY)

OK

3.CHECK HARNESS AND CONNECTOR (STOP AND START SYSTEM CANCEL SWITCH (ECORUN CANCEL SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE STOP AND START SYSTEM CANCEL SWITCH (ECORUN CANCEL SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (STOP AND START SYSTEM CANCEL SWITCH (ECORUN CANCEL SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the stop and start system cancel switch (ecorun cancel switch assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P7-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - STOP AND START SYSTEM CANCEL SWITCH (ECORUN CANCEL SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - STOP AND START SYSTEM CANCEL SWITCH (ECORUN CANCEL SWITCH ASSEMBLY))
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the stop and start system cancel switch (ecorun cancel switch assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H66-5 (ECAN) - P7-5 (ECU) Always Below 1 Ω
H66-5 (ECAN) or P7-5 (ECU) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR