Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 12.3 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0444619 NAVIGATION SYSTEM(for 12.3 Inch Display) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 12.3 Inch Display)  Illumination Circuit  


DESCRIPTION

Power is supplied to the multi-display assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E437685E03
1.167,0.656 3.458,0.854 2.292,0.198 10 false from TAIL Relay 3.479,0.854 4.25,1.052 0.771,0.198 10 false PANEL 0.385,4.031 4.667,4.229 4.281,0.198 10 false Steering Pad Switch Assembly 2.531,3.156 4.552,3.625 2.021,0.469 10 false Spiral Cable Sub-assembly 2.573,5.74 4.885,6.042 2.313,0.302 10 false Combination Meter Assembly 2.583,5.573 3.198,5.771 0.615,0.198 10 false H21 5.688,2.073 6.302,2.271 0.615,0.198 10 false 2 3.521,5.177 4.135,5.375 0.615,0.198 10 false ILL- 5.865,5.188 6.479,5.385 0.615,0.198 10 false ILL- 3.885,5.052 4.5,5.25 0.615,0.198 10 false 1 5.563,6.125 7.115,6.375 1.552,0.25 10 false Multi-display Assembly 5.615,5.063 6.229,5.26 0.615,0.198 10 false 15 5.563,5.958 6.021,6.156 0.458,0.198 10 false H7 2.542,2.99 2.854,3.188 0.313,0.198 10 false H24 3.896,2.646 4.51,2.844 0.615,0.198 10 false 9 3.875,2.083 4.49,2.281 0.615,0.198 10 false 14 3.365,2.083 3.979,2.281 0.615,0.198 10 false IL+2 3.365,2.667 3.979,2.865 0.615,0.198 10 false IL-2 5.854,2.198 6.469,2.396 0.615,0.198 10 false ILL

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the multi-display assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.


Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except multi-display assembly. B
No illumination comes on (multi-display assembly, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the H24 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H24-14 (IL+2) - Body ground Ignition switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY, COMBINATION METER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the H7 multi-display assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H7-2 (ILL) - Body ground Ignition switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H7 multi-display assembly connector.


b.

Disconnect the H21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H7-15 (ILL-) - H21-1 (ILL-) Always Below 1 Ω
H7-15 (ILL-) or H21-1 (ILL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR