These DTCs are stored when a malfunction occurs in the navigation antenna assembly*1 or antenna divider*2.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | GPS Antenna Connection Malfunction(short) | Navigation antenna malfunction | ·
Navigation antenna assembly*1 ·
No. 2 antenna cord sub-assembly*1 ·
Antenna divider*2 ·
Antenna cord sub-assembly*2 ·
Navigation ECU |
| B15C1 | GPS Antenna Connection Malfunction(break) | Navigation antenna power source malfunction | ·
Navigation antenna assembly*1 ·
No. 2 antenna cord sub-assembly*1 ·
Antenna divider*2 ·
Antenna cord sub-assembly*2 ·
Navigation ECU |
*1: w/o Heated Windshield Defroster System
*2: w/ Heated Windshield Defroster System
Check that the No. 2 antenna cord sub-assembly*1 or antenna cord sub-assembly*2 is properly installed and does not have any sharp bends, pinching or loose connections before performing the following procedure.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
*1: w/o Heated Windshield Defroster System
*2: w/ Heated Windshield Defroster System
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Heated Windshield Defroster System) | B |
| NG (w/ Heated Windshield Defroster System) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Remove the No. 2 antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Component without harness connected
(No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 - B-1 | Always | Below 1 Ω |
| A-3a - B-1a | Always | Below 1 Ω |
| A-3 or B-1 - Body ground | Always | 10 kΩ or higher |
| A-3a or B-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
| *a | Component without harness connected
(Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 6 | Always | 10 kΩ or higher |
| 2 - 2a | Always | 243 to 267 Ω |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Component without harness connected
(Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I-2 - B-1 | Always | Below 1 Ω |
| I-2a - B-1a | Always | Below 1 Ω |
| I-2 or B-1 - Body ground | Always | 10 kΩ or higher |
| I-2a or B-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the antenna divider with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG