Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _51 Engine / Hybrid System _086858 CRUISE CONTROL _0418320 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model)  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

A426365E28
1.333,0.969 2.854,1.375 1.521,0.406 10 false Vehicle-to-vehicle Distance Control Switch 0.813,2.594 2.948,2.802 2.135,0.208 10 false Steering Pad Switch Assembly 3.219,2.552 4.396,2.917 1.177,0.365 10 false Spiral Cable Sub-assembly 5.385,2.385 6.677,2.771 1.292,0.385 10 false Forward Recognition Camera 3.021,0.844 3.333,1.042 0.313,0.198 10 false z1 4.219,2 4.531,2.198 0.313,0.198 10 false H24 5.375,2.208 5.781,2.406 0.406,0.198 10 false R5 3.573,0.74 4.188,0.938 0.615,0.198 10 false DIST 2.531,0.74 3.146,0.938 0.615,0.198 10 false DIST 2.531,1.896 3.146,2.094 0.615,0.198 10 false ECC 3.583,1.896 4.198,2.094 0.615,0.198 10 false ECC 5.708,0.854 6.323,1.052 0.615,0.198 10 false LKSW 3.063,0.646 3.219,0.844 0.156,0.198 10 false 8 3.01,1.771 3.292,1.969 0.281,0.198 10 false 12 4.292,0.625 4.563,0.844 0.271,0.219 10 false 6 4.302,1.792 4.458,1.99 0.156,0.198 10 false 2 5.521,0.74 5.677,0.938 0.156,0.198 10 false 3 3.021,1.99 3.333,2.188 0.313,0.198 10 false z1 4.208,0.854 4.521,1.052 0.313,0.198 10 false H24

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the forward recognition camera, replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle-to-vehicle Distance Control Switch Vehicle-to-vehicle distance control switch signal OFF or ON OFF: Vehicle-to-vehicle distance control switch not pushed
ON: Vehicle-to-vehicle distance control switch pushed
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Vehicle-to-vehicle Distance Control Switch
50003 426 4
OK:

The value of the Data List item changes according to the operation of the vehicle-to-vehicle distance control switch.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA AND BODY GROUND)
a.

Disconnect the R5 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H24-6 (DIST) - R5-3 (LKSW) Always Below 1 Ω
H24-2 (ECC) - Body ground Always Below 1 Ω
H24-6 (DIST) or R5-3 (LKSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR